Current Selected Location - Sid Harvey Garden City (0999) Garden City NY

White Rodgers Cooling Controls 50N02A-820 DSI Integrated Furnace Control 24 VAC,white rodgers 50n02a-820

White Rodgers Cooling Controls 50T35-743 Circuit Board
White Rodgers 50T35-743

White Rodgers Cooling Controls 50A56-956 Replacement Integrated Furnace Control, 25 VAC , The 50A56-956 is an automatic gas interrupted ignition control that employs a microprocessor to continually monitor, analyze, and control the proper operation of the gas burner, inducer, and fan. signals interpreted during continual surveillance of the thermostat and flame sensing element initiate automatic ignition of the burner, sensing of the flame, and system shutoff during normal operation. these controls incorporate system fault analysis for quick gas flow shutoff , coupled with automatic ignition retry upon sensing a fault correction.

The 50A55-843 universal silicon carbide integrated ignition module employs a microprocessor which continually monitors, analyzes and controls the proper operation of the gas burner, inducer and fan. This one module will replace most of the 50A5x-xxx integrated ignition carbide modules that have been manufactured by White-Rodgers for most OEM applications. The universal module includes an extensive cross-reference, additional jumper wires, additional wiring harness and a jumper for Trane applications. The module also has terminals for powering a humidifier and electronic air cleaner.

Diagnostic LED
• Additional jumpers to extend the length of the connections Replaces Part #:'s : D330927P01 | D330930P01 | D330934P01 | D340035P01 | D340354P01 | D340774P01 |
  

White Rodgers Cooling Controls 50M56U-801Integrated HIS Furnace Control Board

System diagnostic LED with fault recall
• Fused to protect low voltage system transformers
• 3 fan speeds
• Adapter harness for application flexibility
• 15 sec pre-purge time
• 30/45 heat delay for to fan on, 60/90/120/180 heat delay for to fan off, 2 cool delay for to fan on, 2/60 cool delay for to fan off, default setting
• 5 sec post-purge
• 0.8 sec max flame failure response time
• 2 sec flame failure response time
• 1.5 amp at 25 VAC 50/60 Hz for valve relay, 1.2 amp at 120 VAC 50/60 Hz for ignitor relay
• Surface mount standoffs
• 5 - 93% RH, non-condensing humidity
  

Peerless Boiler Parts 50692 Conversion Kit Nat-LP

Peerless Boiler Parts 50767 Peerless 64-65 Ignition Module,

White Rodgers Cooling Controls 50M56U-843 1-Stage HSI Integrated Furnace Control Kit, 25 VAC, 0.45 amp, 5-1/4" W x 7" H x 1-1/4" D

White Rodgers Cooling Controls 50A55-743 Replacement Integrated Furnace Control, 25 VAC, 0.45 amp, Import The 50A55-743 is an automatic gas interrupted ignition control that employs a microprocessor to continually monitor, analyze, and control the proper operation of the gas burner, inducer, and fan. signals interpreted during continual surveillance of the thermostat and flame sensing element initiate automatic ignition of the burner, sensing of the flame, and system shutoff during normal operation. these controls incorporate system fault analysis for quick gas flow shutoff , coupled with automatic ignition retry upon sensing a fault correction. it is designed as a replacement for the following controls.

• Twinning connection
• Fused to protect low voltage system transformers
• 120 VAC igniter output
• 120 VAC humidifier output
• 120 VAC electronic air cleaner output
• 120 VAC 2-speed PSC circulator output
• 5 amp fuse protection
• Furnace status LED
• Heat fan off delay (dipswitch selectable)
• 1.5 amp valve relay
• 6 amp igniter relay
• 2.2 amp full load - 3.5 amp locked rotor inducer relay
• 14.5 amp full load - 25 amp locked rotor circulator relay
• 1 micro-amp DC minimum current
• 0.10 micro-amp DC max current
• 100 mega-ohm leakage resistance
• Maximum timing specification
• 0.8 sec flame establishing
• Flash code diagnostics The 50A55-743 is an automatic gas interrupted ignition control that employs a microprocessor to continually monitor, analyze, and control the proper operation of the gas burner, inducer, and fan. signals interpreted during continual surveillance of the thermostat and flame sensing element initiate automatic ignition of the burner, sensing of the flame, and system shutoff during normal operation. these controls incorporate system fault analysis for quick gas flow shutoff , coupled with automatic ignition retry upon sensing a fault correction. it is designed as a replacement for the following controls
  

Peerless Boiler Parts 50787 Transformer Primary Voltage

The 50A55-3797 is an automatic gas interrupted ignition control that employs a microprocessor to continually monitor, analyze, and control the proper operation of the gas burner, inducer, and fan. signals interpreted during continual surveillance of the thermostat and flame sensing element initiate automatic ignition of the burner, sensing of the flame, and system shutoff during normal operation. these controls incorporate system fault analysis for quick gas flow shutoff , coupled with automatic ignition retry upon sensing a fault correction. it is designed as a replacement for the following controls.

Fused to protect low Voltage system transformers
• 120 VAC igniter output
• 120 VAC humidifier output
• 120 VAC electronic air cleaner output
• 120 VAC 2-speed PSC circulator output
• 5 amp fuse protection
• Furnace status LED
• Heat fan off delay (dipswitch selectable)
• 1.5 amp valve relay
• 6 amp igniter relay
• 2.2 amp full load - 3.5 amp locked rotor inducer relay
• 14.5 amp full load - 25 amp locked rotor circulator relay
• 1 micro-amp DC minimum current
• 0.1 micro-amp DC max current
• 100 mega-ohm leakage resistance
• Maximum timing specification
• 0.8 sec flame establishing
• 2 sec flame failure response time
• Flash code diagnostics
  

The 50A65-5165 is an automatic gas interrupted ignition control that employs a microprocessor to continually monitor, analyze, and control the proper operation of the gas burner, inducer, and fan. signals interpreted during continual surveillance of the thermostat and flame sensing element initiate automatic ignition of the burner, sensing of the flame, and system shutoff during normal operation. these controls incorporates system fault analysis for quick gas flow shutoff , coupled with automatic ignition retry upon sensing a fault correction. it is designed as a replacement for the following controls.

Twinning connection
• Fused to protect low Voltage system transformers
• 1.5 amp valve relay
• 6 amp igniter relay
• 2.2 amp full load - 3.5 amp locked rotor inducer relay
• 14.5 amp full load - 25 amp locked rotor circulator relay
• 1 micro-amp DC minimum current
• 0.10 micro-amp DC max current
• 100 mega-ohm leakage resistance
• Maximum timing specification
• 0.8 sec flame establishing
• 2 sec flame failure response time
• 77 deg F electrical rating
• Flash code diagnostics, controls gas valve, igniter, blower, inducer, 120 VAC humidifier and air cleaner

Sid Harvey Item #:50A65-5165: Replaces Part #:'s : CNT05165 | CNT5165 |