Brand Name
Connection Size
Refrigerant
Capacity
Length
Width
Height
View:
Item#:
3738
Manufacturer Item:
3738
Manufacturer:
REFRIGERATION RESEARCH INC
Refrigeration Research 1911 Vertical Mount Refrigeration Receiver, 10 lb
  • Refrigeration research receivers have been made continuously for over 50 years
  • They are used widely by original equipment manufacturers throughout the industry
  • They are backed by a reputation for quality and service
  • These receivers with valves and fittings attached are hydrogen brazed for cleanliness and pressure tested for reliability
  • 430 deg F fusible plug is installed on all receivers except #2030, #2039, and #9028
  • All valves are supplied with steel stem caps with copper gaskets and brass flare nuts and caps, all receivers are powder coated for excellent corrosion resistance
  • Pressure tested for 500 psi maximum working pressure
Item#:
1911
Manufacturer Item:
1911
Manufacturer:
REFRIGERATION RESEARCH INC
Air conditioning, heat pump, truck refrigeration and many other applications require intermittent operation of the refrigeration compressor. Especially in remote applications, the suction line may trap or hold quantities of liquid which are suddenly dumped into the compressor as it starts up. This is frequently the cause of broken valves, pistons, broken or bent connecting rods, blown gaskets and bearing washout. Proper installation of the Refrigeration Research suction accumulator in the suction line, just before the compressor, eliminates damage. If correctly sized, relatively large quantities of liquid refrigerant may return through the suction line and the suction accumulator prevents damage to the compressor. Liquid is temporarily held in the suction accumulator and metered back to the compressor along with any oil, at a controlled rate, through the metering orifice. Therefore, damage to the compressor is prevented and the compressor immediately and quietly goes to work.
Item#:
3700-01
Manufacturer Item:
3700-01
Manufacturer:
REFRIGERATION RESEARCH INC
Item#:
3706
Manufacturer Item:
3706
Manufacturer:
REFRIGERATION RESEARCH INC
Henry Technologies S-9130 Steel Universal Adjustable Mechanical Oil Level Regulator, 450 psig Maximum Working, 5 - 90 psig Differential, 3/8 Inch Flanged
  • 3 bolt on 1-7/8 Inch or universal flange compressor connections
  • SAE flare oil and equalization connections
  • Pressure equalization ports for multi compressor applications
  • Adapters available for most popular compress models
  • The shell and caps are made of steel, the float valve is made of brass with a stainless steel needle, the float ball is made of stainless steel and all connections are made of plated steel
Item#:
S-9130
Manufacturer Item:
S-9130
Manufacturer:
HENRY TECHNOLOGIES, INC
Item#:
A-AS 5 97
Manufacturer Item:
060818
Manufacturer:
WHITE-RODGERS COOLING CONTROLS
Item#:
1918
Manufacturer Item:
1918
Manufacturer:
REFRIGERATION RESEARCH INC
Item#:
1921
Manufacturer Item:
1921
Manufacturer:
REFRIGERATION RESEARCH INC
Item#:
3212
Manufacturer Item:
3212
Manufacturer:
REFRIGERATION RESEARCH INC
Item#:
S-5188
Manufacturer Item:
S-5188
Manufacturer:
HENRY TECHNOLOGIES, INC
Item#:
S-5290
Manufacturer Item:
S-5290
Manufacturer:
HENRY TECHNOLOGIES, INC
Henry Technologies S-5587 Non Serviceable Conventional Oil Separator, 7/8" ODS, 3/8" SAE Return, 1/8" NPT Drain
  • The function of a helical oil separator is to remove oil from the discharge gas and return it to the compressor either directly or through an oil management system
  • Conventional oil separators can be used in a wide variety of applications, common applications include multi-compressor racks and remote condensing units
  • These separators are designed for use with scroll and reciprocating type compressors, they are not recommended for screw or rotary vane compressors
  • Conventional oil separators are intended for low pressure oil management systems
  • ODS refrigerant connection
  • SAE flare oil connections
  • Low pressure drop
  • No moving parts within oil separation zone
  • Magnet on oil float to collect debris
  • The main components- shell, end caps and connections are made from carbon steel
  • The separation screens are made from brass
  • The float assemblies are made from stainless steel, brass and copper
Item#:
S-5587
Manufacturer Item:
S-5587
Manufacturer:
HENRY TECHNOLOGIES, INC
View: