Williamsom-Thermoflo GL-53-W Glass Lined Indirect Water Heater, 53.1 Gallon DHW, 2.1 Gallon Boiler, 12 gpm, 140 BTU

• Inspection opening provides easy access to clean and inspect tank
• 2" of dense foam insulation, CFC free and environmentally safe
• Adjustable leveling legs
• Low off cycle losses
• Pressure relief valve provided
• Tank and coil are 100% air pressure/water tested
• Factory installed sacrificial magnesium anode rod

,

Eastern Foundry & Fitting EF98104

Williamsom-Thermoflo GL-42-W Glass Lined Indirect Fired Water Heater, 39.9 Gallon Domestic, 1.7 Gallon Boiler, 8 gpm at 1.6 feet WC, 125 BTU

• Inspection opening provides easy access to clean and inspect tank
• 2" of dense foam insulation, CFC free and environmentally safe
• Adjustable leveling legs
• low off cycle losses
• Pressure relief valve provided
• Tank and coil are 100% air pressure/water tested
• Factory installed sacrificial magnesium anode rod
• 10-years residential and 7-years commercial warranty

,

Eastern Foundry & Fitting EF98103

Williamsom-Thermoflo GL-32-W Glass Lined Indirect Water Heater, 29.6 Gallon DHW, 1.6 Gallon Boiler, 10 gpm, 115 BTU

• Inspection opening provides easy access to clean and inspect tank
• 2" of dense foam insulation, CFC free and environmentally safe
• Adjustable leveling legs
• Low off cycle losses
• Pressure relief valve provided
• Tank and coil are 100% air pressure/water tested
• Factory installed sacrificial magnesium anode rod

,

GL-32-W

The SuperStor ultra indirect water heat is a culmination of over 30 years of indirect system manufacturing experience. The 316L stainless steel tank resists corrosion and eliminates the need for anode rods, allowing for the system to be virtually maintenance free. The heater draws energy from a boiler and thus does not need its own heat source. Hot boiler water flows through an internal heat exchanger in the tank, heating the domestic water. The SuperStor boasts three to five times more recovery than conventional gas-fired or electric water heaters.

• Stainless steel internal bent hot water outlet tube
• Attractive silver finish cover that resists dents and corrosion
• High output finned cupronickel heat exchanger provides maximum efficiency 11 fins per"
• 316L stainless steel tank for high temperatures and corrosion resistance
• Environmentally safe, CFC free water blown, 2" thick foam insulation allows less than 1/2 deg F heat loss per hour
• Immersion type stainless steel control well

,

htp ssu60

,

SSU60

The SuperStor ultra indirect water heat is a culmination of over 30 years of indirect system manufacturing experience. The 316L stainless steel tank resists corrosion and eliminates the need for anode rods, allowing for the system to be virtually maintenance free. The heater draws energy from a boiler and thus does not need its own heat source. Hot boiler water flows through an internal heat exchanger in the tank, heating the domestic water. The SuperStor boasts three to five times more recovery than conventional gas-fired or electric water heaters.

• Stainless steel internal bent hot water outlet tube
• Attractive silver finish cover that resists dents and corrosion
• High output finned cupronickel heat exchanger provides maximum efficiency 11 fins per"
• 316L stainless steel tank for high temperatures and corrosion resistance
• Environmentally safe, CFC free water blown, 2" thick foam insulation allows less than 1/2 deg F heat loss per hour
• Immersion type stainless steel control well

,

htp ssu45

,

SSU45

Heat-Flo offers quality indirect water heating systems that provide abundant hot water, low operating cost, and long life. Hot water from any heating boiler is circulated through the coil inside to heat all the water in the tank. Simply add another zone to your existing heating boiler.

• Large, smooth-wall coils deliver full output for years
• No finned tubing to collect lime and sediment
• Includes over 2" of insulation and a flexible thermoplastic jacket that will not dent or corrode, and less than 10/hr heat loss
• All connections are on top on the standard units for a neat, clean installation
• Brass drain and relief valves are factory installed
• Standard Honeywell control and well for reliability and easy service
• Low operating cost

,

HF-60

,

Heat-Flo Water Heaters HF-60

Heat-Flo offers quality indirect water heating systems that provide abundant hot water, low operating cost, and long life. Hot water from any heating boiler is circulated through the coil inside to heat all the water in the tank. Simply add another zone to your existing heating boiler.

• Large, smooth-wall coils deliver full output for years
• No finned tubing to collect lime and sediment
• Includes over 2" of insulation and a flexible thermoplastic jacket that will not dent or corrode, and less than 10/hr heat loss
• All connections are on top on the standard units for a neat, clean installation
• Brass drain and relief valves are factory installed
• Standard Honeywell control and well for reliability and easy service
• Low operating cost

,

HF-50

,

Heat-Flo Water Heaters HF-50

Heat-flo offers quality indirect water heating systems that provide abundant hot water, low operating cost and long life. Hot water from any heating boiler is circulated through the coil inside to heat all the water in the tank. Simply add another zone to your existing heating boiler.

• Large, smooth-wall coils deliver full output for years
• No finned tubing to collect lime and sediment
• Includes over 2" of insulation and a flexible thermoplastic jacket that will not dent or corrode, and less than 10 per hr heat loss
• All connections are on top on the standard units for a neat, clean installation
• Brass drain and relief valves are factory installed
• Standard Honeywell control and well for reliability and easy service
• Low operating cost

,

Heat-Flo Water Heaters HF-40

,

HF-40

Diversified Heat Transfer TX-80 Indirect Water Heater 80 Gallon Stainless Steel

PROTECTION AGAINST CORROSION The DHT TX Series of stainless steel water heaters are manufactured from 1.4521 Niobium-Titanium stabilized steel, which offers protection against corrosion.

REDUCED ENERGY COST

The TX Series Water Heaters offer rapid recovery rates and an industry leading heat loss performance of less than 239 btu/h. This can reduce energy costs by up to 15 %. This is achieved by injecting high density CFC free and fire retardant polyurethane foam insulation.

REDUCED MAINTENANCE COST

Unlike glass lined water heaters, an anode is not needed thus reducing maintenance costs for the consumer.

PATENTED AND ENVIRONMENTALLY FRIENDLY

All good quality stainless steel water heaters need pickling to prolong their life. Pickling is essential for products installed in areas where the water has a high chloride or lime value. To avoid the environmental impact of pickling, a patented in-house pickling process was created to reuse up to 95% of the water consumed. All discharged water is also cleaned of chemicals before being released back in to the environment, and the extracted chemicals are treated and recycled.

LEADING WELDING TECHNOLOGY

The DHT TX Series of stainless steel water heaters are TIG welded using a fully automated welding technique,which is clean and smooth to prevent crevice corrosion. The welding technique reduces stress and damage to the integrity of the steel and eliminates product rejections during production. The TX stainless steel water heaters offerthe user excellent performance and service for many years.,

Diversified Heat Transfer TX-80

,

TX-80

Diversified Heat Transfer TX-50 Indirect Water Heater 50Gallon Stainless Steel

PROTECTION AGAINST CORROSION The DHT TX Series of stainless steel water heaters are manufactured from 1.4521 Niobium-Titanium stabilized steel, which offers protection against corrosion.

REDUCED ENERGY COST

The TX Series Water Heaters offer rapid recovery rates and an industry leading heat loss performance of less than 239 btu/h. This can reduce energy costs by up to 15 %. This is achieved by injecting high density CFC free and fire retardant polyurethane foam insulation.

REDUCED MAINTENANCE COST

Unlike glass lined water heaters, an anode is not needed thus reducing maintenance costs for the consumer.

PATENTED AND ENVIRONMENTALLY FRIENDLY

All good quality stainless steel water heaters need pickling to prolong their life. Pickling is essential for products installed in areas where the water has a high chloride or lime value. To avoid the environmental impact of pickling, a patented in-house pickling process was created to reuse up to 95% of the water consumed. All discharged water is also cleaned of chemicals before being released back in to the environment, and the extracted chemicals are treated and recycled.

LEADING WELDING TECHNOLOGY

The DHT TX Series of stainless steel water heaters are TIG welded using a fully automated welding technique,which is clean and smooth to prevent crevice corrosion. The welding technique reduces stress and damage to the integrity of the steel and eliminates product rejections during production. The TX stainless steel water heaters offerthe user excellent performance and service for many years.,

diversified heat transfer tx-50

,

TX-50

Diversified Heat Transfer TX-40 Indirect Water Heater 42Gallon Stainless Steel

PROTECTION AGAINST CORROSION The DHT TX Series of stainless steel water heaters are manufactured from 1.4521 Niobium-Titanium stabilized steel, which offers protection against corrosion.

REDUCED ENERGY COST

The TX Series Water Heaters offer rapid recovery rates and an industry leading heat loss performance of less than 239 btu/h. This can reduce energy costs by up to 15 %. This is achieved by injecting high density CFC free and fire retardant polyurethane foam insulation.

REDUCED MAINTENANCE COST

Unlike glass lined water heaters, an anode is not needed thus reducing maintenance costs for the consumer.

PATENTED AND ENVIRONMENTALLY FRIENDLY

All good quality stainless steel water heaters need pickling to prolong their life. Pickling is essential for products installed in areas where the water has a high chloride or lime value. To avoid the environmental impact of pickling, a patented in-house pickling process was created to reuse up to 95% of the water consumed. All discharged water is also cleaned of chemicals before being released back in to the environment, and the extracted chemicals are treated and recycled.

LEADING WELDING TECHNOLOGY

The DHT TX Series of stainless steel water heaters are TIG welded using a fully automated welding technique,which is clean and smooth to prevent crevice corrosion. The welding technique reduces stress and damage to the integrity of the steel and eliminates product rejections during production. The TX stainless steel water heaters offerthe user excellent performance and service for many years.,

diversified heat transfer tx-40

,

TX-40

Diversified Heat Transfer Techtanium TT-40 Powder Coat Painted Steel Jacket Indirect Water Heater, 40 Gallon, 10 gpm, 120000 BTU

• Extra large heat exchanger surface area - high recovery and continuous flow for abundant hot water
• Titanium glass lined - high elasticity that adapts to expansion and contraction for added strength and durability, provides a resistant layer of protection against corrosion
• Exterior steel jacket with powder coat paint - durable and solid for life lasting exterior appearance, polyurethane foam (PUF) insulation reduces standby heat loss
• Side connections for TT series
• Works with any hydronic heat source for domestic hot water
• Environmentally friendly polyurethane insulation limits heat loss and is both CFC and HFC- free
• Polyurethane foam for outstanding insulation and reduced power consumption- CFC free
• All models supplied magnesium anti-corrosion anodes
• TT models - (2) magnesium anti-corrosion anodes
• Environmentally and Installer friendly
• Includes - Honeywell L4006A aquastat, immersion well
• 7 years residential, 3 years commercial warranty

,

diversified heat transfer tt-40

,

TT-40