• The P7 series single packaged air conditioners are high efficiency self contained cooling units that can be installed on a slab
• Quality compressor - state of the art compressor is standard equipment
• High pressure switches ensure long compressor life
• Micro-channel coils both indoor and outdoor all aluminum coils are designed to optimize heat transfer, minimize size and cost and increase durability and reliability, eliminates corrosion
• ECM blower motor fixed torque energy efficient brushless DC ECM motor
• Permanently lubricated condenser motor - a heavy-duty PSC motor for long lasting reliability and quiet operation
• Low voltage transformer - includes 3 amp fuse to protect low voltage circuit
• Liquid line filter drier factory installed at a convenient location for service
• Designed using Galvanized steel with a polyester urethane coat finish, 950 hr salt spray finish is 1.5 mil thick and resists corrosion 50% better than comparable units
• Compact footprint and profile make the P7 series easy to install and transport
• 0" clearance to combustibles on duct side of the unit allows for installations in tight areas
• Wire guard coated with earth friendly epoxy and plastic mesh hail guard that will never rust and protects the units coil from being damaged
• Raised base pan allows water to drain away from the unit
• Easy compressor and control access designed to make servicing easier for the contractor, access panels are provided to all controls and the compressor from side of the unit
• Easy access to the evaporator coil for cleaning, blower assembly removal and general maintenance
• Drain trap design optimizes drainage capabilities
• Removable top grille assembly - allows ease of service to the fan motor

Frigidaire P7RE-036K

• R410A
• Copper tube/aluminum fin condenser and evaporator coils
• Dehumidification mode (airflow reduction) on all models
• Installs easily on a rooftop or at ground level
• Easy three-panel accessibility for maintenance and installation
• Easily converts to down discharge applications
• Combination gas heating and electric cooling
• Induced-draft combustion and venting
• Direct spark ignition
• High efficiency ECM indoor blower motor on all models
• Vertical condenser fan discharge
• Full perimeter steel base rails
• High pressure switch provides added reliability for the compressor
• Aluminized steel tubular heat exchanger and 2 spacing wire grilles on PGD4 models (00), Stainless Steel tubular heat exchanger and hail guard (3/8 spacing) wire grilles on PGS4 models Single phase models with factory installed tin-plated copper evaporator main tubes PGD4 (TP), PGS4 (GP)
• 3 year No Hassle Replacement limited warranty
• 10 year parts limited warranty (including compressor and coils) with timely registration
• 5 year parts limited warranty and 20 year heat exchanger limited warranty if not registered within 90 days of original installation.
• 15 year heat exchanger limited warranty
• 5 year compressor limited warranty

  INTERNATIONAL COMFORT PRODUCTS PGD424060K000G

• Copper tube/aluminum fin condenser and evaporator coils
• Dehumidification mode (airflow reduction) on all models
• Installs easily on a rooftop or at ground level
• Easy 3-panel accessibility for maintenance and installation
• Easily converts to down discharge applications
• Combination gas heating and electric cooling
• Induced draft combustion and venting
• High efficiency ECM indoor blower motor on all models
• Vertical condenser fan discharge
• Full perimeter steel base rails
• High and low pressure switches provide added reliability for the compressor
• Stainless steel heat exchanger
• 10 years heat exchanger limited warranty
• 5 years compressor limited warranty
• 1 year parts limited warranty

• The P7 series single packaged air conditioners are high efficiency self contained cooling units that can be installed on a slab
• Quality compressor - state of the art compressor is standard equipment
• High pressure switches ensure long compressor life
• Micro-channel coils both indoor and outdoor all aluminum coils are designed to optimize heat transfer, minimize size and cost and increase durability and reliability, eliminates corrosion
• ECM blower motor fixed torque energy efficient brushless DC ECM motor
• Permanently lubricated condenser motor - a heavy-duty PSC motor for long lasting reliability and quiet operation
• Low voltage transformer - includes 3 amp fuse to protect low voltage circuit
• Liquid line filter drier factory installed at a convenient location for service
• Designed using Galvanized steel with a polyester urethane coat finish, 950 hr salt spray finish is 1.5 mil thick and resists corrosion 50% better than comparable units
• Compact footprint and profile make the P7 series easy to install and transport
• 0" clearance to combustibles on duct side of the unit allows for installations in tight areas
• Wire guard coated with earth friendly epoxy and plastic mesh hail guard that will never rust and protects the units coil from being damaged
• Raised base pan allows water to drain away from the unit
• Easy compressor and control access designed to make servicing easier for the contractor, access panels are provided to all controls and the compressor from side of the unit
• Easy access to the evaporator coil for cleaning, blower assembly removal and general maintenance
• Drain trap design optimizes drainage capabilities
• Removable top grille assembly - allows ease of service to the fan motor

Frigidaire P7RE-030K

• Name Rheem RSPM-A036JK000 - Classic 3 Ton, 14 SEER, Packaged Air Conditioner - Dedicated Horizontal, 208-230 V, 1 Ph, 60 Hz
• Weight 333lbs
• Length 59.9"
• Width 34.0"
• Height 33.5"
• SEER 14
• EER 12.2
• Refrigerant R-410A
• CFM 3,400
• Cooling Capacity 36,000 BTU
• Air Flow Horizontal
• Voltage 208/230 VAC
• Phase Single
• Minimum Circuit Amps 22.6
• Maximum Fuse Size 40
• Blower Motor HP 1/2 HP
• Condenser Motor HP 1/3 HP
• Drive Type Direct Drive
• Energy Star Rated Yes

  Rheem A/C RSPMA036JK000

• R410A
• Copper tube/aluminum fin condenser and evaporator coils
• Dehumidification mode (airflow reduction) on all models
• Installs easily on a rooftop or at ground level
• Easy three-panel accessibility for maintenance and installation
• Easily converts to down discharge applications
• Combination gas heating and electric cooling
• Induced-draft combustion and venting
• Direct spark ignition
• High efficiency ECM indoor blower motor on all models
• Vertical condenser fan discharge
• Full perimeter steel base rails
• High pressure switch provides added reliability for the compressor
• Aluminized steel tubular heat exchanger and 2 spacing wire grilles on PGD4 models (00), Stainless Steel tubular heat exchanger and hail guard (3/8 spacing) wire grilles on PGS4 models Single phase models with factory installed tin-plated copper evaporator main tubes PGD4 (TP), PGS4 (GP)
• 3 year No Hassle Replacement limited warranty
• 10 year parts limited warranty (including compressor and coils) with timely registration
• 5 year parts limited warranty and 20 year heat exchanger limited warranty if not registered within 90 days of original installation.
• 15 year heat exchanger limited warranty
• 5 year compressor limited warranty

  International Comfort Products PGD430060K000H

International Comfort Products PAJ460000KTP0A

• R410A
• Copper tube/aluminum fin condenser and evaporator coils
• Dehumidification mode (airflow reduction) on all models
• Installs easily on a rooftop or at ground level
• Easy three-panel accessibility for maintenance and installation
• Easily converts to down discharge applications
• Combination gas heating and electric cooling
• Induced-draft combustion and venting
• Direct spark ignition
• High efficiency ECM indoor blower motor on all models
• Vertical condenser fan discharge
• Full perimeter steel base rails
• High pressure switch provides added reliability for the compressor
• Aluminized steel tubular heat exchanger and 2 spacing wire grilles on PGD4 models (00), Stainless Steel tubular heat exchanger and hail guard (3/8 spacing) wire grilles on PGS4 models Single phase models with factory installed tin-plated copper evaporator main tubes PGD4 (TP), PGS4 (GP)
• 3 year No Hassle Replacement limited warranty
• 10 year parts limited warranty (including compressor and coils) with timely registration
• 5 year parts limited warranty and 20 year heat exchanger limited warranty if not registered within 90 days of original installation.
• 15 year heat exchanger limited warranty
• 5 year compressor limited warranty