Metal-Fab 4M90 B-Vent 90 Degree 4"

Metal-Fab 4M90

Centrotherm Eco Systems Innoflue IANS02 Steel Locking Connector Ring for Innoflue Single Wall (SW) Connections (Pipe to Pipe, Pipe to Fitting, Pipe to Adapter, etc), 2"

• Provides reinforcement at joints to support loads of up to 99 lb
• 32 - 230 deg F maximum temperature

Duro Dyne IANS02

Hart & Cooley 0.012" Aluminum Inner and 0.018" G90 Galvanized Steel

• Deep locking groove assures solid joint and secure lock
• Corrosion resistant aluminum inner wall for rapid warm-up
• Unique locking band provides 360 deg turning radius of the pipe and fittings
• Locking band slides over tabs easily, locks firmly without twisting
• Locking tabs hold pipe securely together, can be easily unlocked
• Positive stop provides proper alignment and positive fit for mating end of pipe or fitting
• Reinforced ends curled bead on end of outer pipe for rigidity and strength
• The allowable minimum clearance to combustibles is 1"
• A full set of installation instructions are supplied with caps and supports
  
  
  Hart & Cooley 4REA90 B-Vent 90 Degree Elbow 4" Natural Gas Aluminum Inner & Galvanized Steel Outer

  Hart & Cooley 4REA90

Centrotherm Eco Systems Innoflue ISELL0287 Gray Polypropylene Single Wall 87 Degree Vent Elbow, 2"

• Industry leading 2 mm wall thickness provides impact protection
• Polypropylene is highly corrosion resistant, making it suitable for both gas and oil fired appliances
• Zero clearance to combustibles
• PPs-UV black termination components provide enhanced UV protection
• High quality joint connections for a consistently tight fit up
• No adhesives required
• Allows for post installation adjustments
• Immediate use of appliance upon installation
• Light weight allows for ease of handling and installation
• Reduced labor costs up to 75%
• No special tools are required
• No solvent based PVC or CPVC adhesives per IE credit 4.1

Edwards & West ISELL0287

All FasNSeal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on FasNSeal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All FasNSeal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

• FasNSeal is for use with natural gas or propane categories II, III and IV appliances or type BH gas vent systems, having a maximum rated operating temperature of 480 deg F and a maximum positive pressure of 15" water column
• FasNSeal can be used on a wide range of applications, including high efficiency gas boilers, furnaces, booster heaters, pool heaters, water heaters, unit heaters or tankless water heaters
  
  
  M & G Duravent FSELB9003 Fas-n-Seal 90 Degree Elbow 3"

  M & G Duravent FSELB9003

Centrotherm Eco Systems Innoflue ISELL0245 Gray Polypropylene Single Wall 45 Degree Vent Elbow, 2"

• Industry leading 2 mm wall thickness provides impact protection
• Polypropylene is highly corrosion resistant, making it suitable for both gas and oil fired appliances
• Zero clearance to combustibles
• PPs-UV black termination components provide enhanced UV protection
• High quality joint connections for a consistently tight fit up
• No adhesives required
• Allows for post installation adjustments
• Immediate use of appliance upon installation
• Light weight allows for ease of handling and installation
• Reduced labor costs up to 75%
• No special tools are required
• No solvent based PVC or CPVC adhesives per IE credit 4.1

Edwards & West ISELL0245

Centrotherm Eco Systems Innoflue IANS03 Steel Locking Connector Ring for Innoflue Single Wall (SW) Connections (Pipe to Pipe, Pipe to Fitting, Pipe to Adapter, etc), 3"

• Provides reinforcement at joints to support loads of up to 99 lb
• 32 - 230 deg F maximum temperature

Duro Dyne IANS03

All FasNSeal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on FasNSeal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All FasNSeal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

• FasNSeal is for use with natural gas or propane categories II, III and IV appliances or type BH gas vent systems, having a maximum rated operating temperature of 480 deg F and a maximum positive pressure of 15" water column
• FasNSeal can be used on a wide range of applications, including high efficiency gas boilers, furnaces, booster heaters, pool heaters, water heaters, unit heaters or tankless water heaters
  
  
  M & G Duravent FSVL3603 Fas-n-Seal Gas Vent Pipe 3" x 36" Natural Gas Stainless Steel

  M & G Duravent FSVL3603

All FasNSeal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on FasNSeal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All FasNSeal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

• FasNSeal is for use with natural gas or propane categories II, III and IV appliances or type BH gas vent systems, having a maximum rated operating temperature of 480 deg F and a maximum positive pressure of 15" water column
• FasNSeal can be used on a wide range of applications, including high efficiency gas boilers, furnaces, booster heaters, pool heaters, water heaters, unit heaters or tankless water heaters
  
  
  M & G Duravent FSVL2403 Fas-n-Seal Gas Vent Pipe 3" x 24" Natural Gas Stainless Steel

  M & G Duravent FSVL2403

An economical venting system used for relining masonry chimney for natural gas or liquid propane category, draft hood equipped appliances and appliances tested and listed to use Type B gas vent for a wide range of applications, including natural gas fireplaces, gas-fired furnaces, boilers, water heaters, and wall or space heating applications. Protects the masonry chimney from damaging effects of flue product condensation.

• DuraFlex aluminum is designed for flexible relining masonry chimneys when using natural gas or liquid propane
• 1-wall construction
• 0" clearance to masonry
• DuraFlex aluminum length, duraflex aluminum cap, duraflex top plate, and duraflex mortar sleeve included
• Limited lifetime warranty
• Includes DuraFlex AL length, DuraFlex AL cap, DuraFlex top plate and, DuraFlex mortar sleeve

Sid Harvey Item #:TLK0535: Replaces Part #:'s : 24682

M & G Duravent TLK0535

Hart & Cooley 0.012" Aluminum Inner and 0.018" G90 Galvanized Steel

• Deep locking groove assures solid joint and secure lock
• Corrosion resistant aluminum inner wall for rapid warm-up
• Unique locking band provides 360 deg turning radius of the pipe and fittings
• Locking band slides over tabs easily, locks firmly without twisting
• Locking tabs hold pipe securely together, can be easily unlocked
• Positive stop provides proper alignment and positive fit for mating end of pipe or fitting
• Reinforced ends curled bead on end of outer pipe for rigidity and strength
• The allowable minimum clearance to combustibles is 1"
• A full set of installation instructions are supplied with caps and supports
  
  
  Hart & Cooley 4RPx5 B-Vent Pipe 4" x 60" Natural Gas Aluminum Inner & Galvanized Steel Outer

  Hart & Cooley 4RPX5

Hart & Cooley 0.012" Aluminum Inner and 0.018" G90 Galvanized Steel

• Deep locking groove assures solid joint and secure lock
• Corrosion resistant aluminum inner wall for rapid warm-up
• Unique locking band provides 360 deg turning radius of the pipe and fittings
• Locking band slides over tabs easily, locks firmly without twisting
• Locking tabs hold pipe securely together, can be easily unlocked
• Positive stop provides proper alignment and positive fit for mating end of pipe or fitting
• Reinforced ends curled bead on end of outer pipe for rigidity and strength
• The allowable minimum clearance to combustibles is 1"
• A full set of installation instructions are supplied with caps and supports
  
  
  Hart & Cooley 4RPx12 B-Vent Pipe 4" x 12" Natural Gas Aluminum Inner & Galvanized Steel Outer

  Hart & Cooley 4RPX12