Fujitsu FH3017TPSJSN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections

• 42K BTU 3-1/2 Ton
• 208/230/1 VA
• 21" Wide
• PSC Motor
• Multi-Position,
  
  
  
  

  Fujitsu FH4221TPSASN

Features

Horizontal application only

Accessory field-installed electric heat kits available in 3, 5, 6, 7.5, or 10 kW

40 VA 208/230-1-60 supply voltage

All Models use R-410A TXV metering device

All Aluminum coils

Adjustable condensate drainpan

FMC4X & FMC4Z

Horizontal return applications require field fabricated bottom cover or solid access panel accessory kit

Cabinets meet the requirement of 1.4% cabinet leakage rate when texted to ASHRAE Standard 193

Cabinets constructed to prevent cabinet sweating

Refrigerant lines and electrical connections can be run out the back or side of casing

PSC motor on all FMU4X & FMC4X models

ECM motor on all FMU4Z & FMC4Z models

Easy to Install and Service

A-coil design for maximum surface area

Multiple electrical, refrigerant lineset and drain line entry for application flexibilty Primary and secondary drain connections exit from the back or side of the cabinet.

Supports furred-down ceiling open return and ducted return applications

Sweat connections for long term reliability

Grooved aluminum tube / aluminum fin coils on FMU4X &

FMC4X models with "AL" in the 10th and 11th position of model number

International Comfort Products FMC4Z3000AL

REFRIGERATION CIRCUIT

Copeland Scroll® Ultratech compressors on all models

Crankcase Heater factory installed

Suction line accumulator factory installed

Biflow filterdrier included for field installation

Integrated solid state control with TimeTemperature Defrost

High and low pressure switches

Discharge gas thermostat

Copper tube / aluminum fin coil PERFORMANCE

Self configuring installation capabilities with Ion® System Control

Outdoor temperature sensor factory installed

Ball Bearing PSC Fan Motors on all models

High performance compressor sound shield standard

Isolation compressor grommets EASY TO INSTALL AND SERVICE

Text based diagnostics with the Ion® System Control

Only 2 control wires required from communicating indoor unit to condenser

Easy access service valves on all models

Innovative control box design

External high and low refrigerant service ports

Only two screws to access control panel

Factory charged with R410A refrigerant BUILT TO LAST

High gloss, bakedon powder coat finish over galvanized steel

Postpainted (black) coil fins

Coated, weatherresistant cabinet screws

Coated inlet grille with 3/8 (10mm) spacing for extra protection (hail guard)

Corner posts for extra strength and style

International Comfort Products CHS072HAA0A00A

REFRIGERATION CIRCUIT

Copeland Scroll compressors on all models

Suction line accumulator factory installed

Biflow filterdrier included for field installation

Integrated solid state control with TimeTemperature Defrost

High and Low pressure switches

Copper tube / aluminum fin coil EASY TO INSTALL AND SERVICE

Easy Access service valves on all models

External high and low refrigerant service ports

Only two screws to access control panel

Factory charged with R410A refrigerant BUILT TO LAST

Bakedon powder coat finish over galvanized steel

Postpainted (black) coil fins

Coated, weatherresistant cabinet screws

Coated inlet grille with 3/8 (10mm) grille spacing for extra protection

International Comfort Products NXH648GKP

REFRIGERATION CIRCUIT

Copeland Scroll compressors on all models

Suction line accumulator factory installed

Biflow filterdrier included for field installation

Integrated solid state control with TimeTemperature Defrost

High and Low pressure switches

Copper tube / aluminum fin coil EASY TO INSTALL AND SERVICE

Easy Access service valves on all models

External high and low refrigerant service ports

Only two screws to access control panel

Factory charged with R410A refrigerant BUILT TO LAST

Bakedon powder coat finish over galvanized steel

Postpainted (black) coil fins

Coated, weatherresistant cabinet screws

Coated inlet grille with 3/8 (10mm) grille spacing for extra protection

International Comfort Products NXH618GKP

REFRIGERATION CIRCUIT

Copeland Scroll Ultratecht compressors on all models

Crankcase Heater factory installed

Suction line accumulator factory installed

Bi- flow filter- drier included for field installation

Integrated solid state control with Time- Temperature Defrost

High and low pressure switches

Discharge gas thermostat

Copper tube / aluminum fin coil PERFORMANCE

Self configuring installation capabilities with Observer Communicating Wall Control

Outdoor temperature sensor factory installed

Ball Bearing PSC Fan Motors on all models

High performance compressor sound shield standard

Isolation compressor grommets EASY TO INSTALL AND SERVICE

Text based diagnostics with Observer Communicating Wall Control

Only 2 control wires required from communicating indoor unit to condenser

Easy access service valves on all models

Innovative control box design

External high and low refrigerant service ports

Only two screws to access control panel

Factory charged with R- 410A refrigerant BUILT TO LAST

High gloss, baked- on powder coat finish over galvanized steel

Post- painted (black) coil fins

Coated, weather- resistant cabinet screws

Coated inlet grille with 3/8 (10mm) spacing for extra protection (hail guard)

Corner posts for extra strength and style

International Comfort Products T5H8T60AKAAA

REFRIGERATION CIRCUIT

Copeland Scroll Ultratecht compressors on all models

Crankcase Heater factory installed

Suction line accumulator factory installed

Bi- flow filter- drier included for field installation

Integrated solid state control with Time- Temperature Defrost

High and low pressure switches

Discharge gas thermostat

Copper tube / aluminum fin coil PERFORMANCE

Self configuring installation capabilities with Observer Communicating Wall Control

Outdoor temperature sensor factory installed

Ball Bearing PSC Fan Motors on all models

High performance compressor sound shield standard

Isolation compressor grommets EASY TO INSTALL AND SERVICE

Text based diagnostics with Observer Communicating Wall Control

Only 2 control wires required from communicating indoor unit to condenser

Easy access service valves on all models

Innovative control box design

External high and low refrigerant service ports

Only two screws to access control panel

Factory charged with R- 410A refrigerant BUILT TO LAST

High gloss, baked- on powder coat finish over galvanized steel

Post- painted (black) coil fins

Coated, weather- resistant cabinet screws

Coated inlet grille with 3/8 (10mm) spacing for extra protection (hail guard)

Corner posts for extra strength and style

Tempstar TCH624GK

REFRIGERATION CIRCUIT

Scroll compressors on all models

Suction line accumulator factory installed

Bi- flow filter- drier included for field installation

Integrated solid state control with Time- Temperature Defrost

External high and low refrigerant service ports

Copper tube / aluminum fin coil PERFORMANCE

Communicating, self- configuring operation when used with Observer Wall Control (TSTAT0201CW)

Outdoor temperature sensor factory installed

Compressor sound blanket standard

Isolation compressor grommets EASY TO INSTALL AND SERVICE

Text based diagnostics with Observer Communicating Wall Control

Easy access service valves on all models

Innovative control box design

High and low pressure switches

Only two screws to access control panel

Factory charged with R- 410A refrigerant

Sid Harvey T397-215