Tjernlund 106-3 In-Line Draft Inducer 14" 14-3/4" W x 17" H x 10" D,
,

Tjernlund 106-3

Tjernlund D-3 Aluminized Steel Housing Inline Draft Inducer, 115 VAC, 0.96 amp, 1550 RPM, 1/20 HP

• Venturi action starts air moving up the stack instantly and keeps it moving smoothly
• In-line inducers are built for long-lasting, trouble-free service
• Vari-draft control permits adjustment to individual job requirements
• Vents/chimneys utilizing in-line draft inducers must be vertically terminated above the roof line
• Solves venting problems: Undersized chimneys, negative pressures, long horizontal vent connectors, down drafts, cold equipment starts, restrictive heat exchangers/combustion chambers
• 1 year warranty Tjernlund D-3 Aluminized Steel Housing Inline Draft Inducer, 115 VAC, 0.96 amp, 1550 RPM, 1/20 HPSid Harvey Item #:106-1: Replaces Part #:'s : x89-444,
  
  ,
  

  Tjernlund 106-1

Tjernlund I Inline Draft Inducer, 115 VAC , 1/4 HP, 1725 RPM

,
,

Tjernlund 106-2

Tjernlund Specially designed to terminate Tjernlund Side Wall Vent Systems. They are also an approved method of terminating many horizontally vented appliances. Vent hoods feature heavy duty, corrosion resistant aluminum construction. Models VH1-3, 4 and 6 also have an additional heat shield for built in clearances from combustibles. Building exteriors are kept clean while the aesthetics of the structure remain undisturbed. All mounting hardware is included.

• 8" square rough-in
• Mounting hardware

Sid Harvey Item #:106-20: Replaces Part #:'s : x89-442,
,

Tjernlund 106-20

Tjernlund Specially designed to terminate Tjernlund Side Wall Vent Systems. They are also an approved method of terminating many horizontally vented appliances. Vent hoods feature heavy duty, corrosion resistant aluminum construction. Models VH1-3, 4 and 6 also have an additional heat shield for built in clearances from combustibles. Building exteriors are kept clean while the aesthetics of the structure remain undisturbed. All mounting hardware is included.

• 9" rough-in diameter
• Mounting hardware

Sid Harvey Item #:106-21: Replaces Part #:'s : x81-965,
,

Tjernlund 106-21

Tjernlund The SideShot models SS1 and SS2 SideWall Vent Systems include the UC1 Universal Control for increased safety, performance and reliability. Designed for oil fired heating equipment or a deluxe gas vent system. Patented vent termination propels flue gases at high velocities away from the building exterior, a necessity when venting oil fired equipment. Both models can be installed with zero clearance to combustible materials and have stainless steel construction in critical areas. Factory wired safety and operating controls allow simple interlock with any burner. The new model SS2 features a self-cleaning stainless steel, backward inclined impeller and sealed ball bearing motor for virtually maintenance free installations. Ultra-fine draft adjustment and slide-out access to all internal components. Easy multiple appliance interlocks with our MAC Series multiple appliance controls.

• Use to side wall vent non-condensing oil fired boilers, water heaters and furnaces that otherwise would require a conventional roof top terminated chimney
• Built-in interlock control with redundant high limit safety switch interfaces easily with thermostat, aquastat or primary controls
• Adjustable pre and post purge timing and easy fault code retrieval
• Stainless steel construction in all critical components including outdoor terminus
• Patented design jets flue gases away from the outside wall to eliminate potential staining of siding

Sid Harvey Item #:106-10: Replaces Part #:'s : 6H167,
,

Tjernlund 106-10

Tjernlund 950-0800 Head Cooling Fan Motor 460 VAC

Tjernlund Motor 950-0800

Tjernlund 950-0640 High Limit Switch SS-1,
,

Tjernlund 950-0640

Tjernlund 950-0635 Steel Replacement Blower Wheel, 5/8" Bore

,
,

Tjernlund 950-0635

Tjernlund 950-0017 Stainless Steel Impeller Wheel Kit

,
,

Tjernlund 950-0017