Weil-Mclain WMCGA6PIDNS3

Weil-Mclain WMCGA4PIDNS3

Weil-Mclain CGA4PIDLS3

weil-mclain cga3pidns3

• Durable design with low maintenance and factory tested
• Unique 7 pass heat exchanger design maximizes heat transfer
• Insulated extended steel jacket
• Cast iron sections with built-in air separator
• Condensing stainless steel secondary heat exchanger with air separator
• Steel base, control module with indicator lights, blower assembly with observation port
• Gas/air manifold assembly, gas/air orifice plate for natural gas and separate plate furnished for conversion to propane
• Stainless steel burner cone and ring assembly, negative regulation gas valve, hot surface ignition system, air pressure switch
• Taco 007 system circulator
• Built-in bypass circulator system with sensor for temperature control, condensate drain trap, sidewall vent termination kit, 40 VA transformer, electrical junction box
• 30 psi ASME relief valve boiler sections and secondary heat exchanger tested for 50 psi working pressure
• Water temperature limit switch, section block temperature limit switch, combination pressure and temperature gauge, drain valve, flue thermal fuse
• 1/2" gas connection
• 3-section
• 1" minimum pipe size

Weil-Mclain CGI7PINS4

Peerless Boiler ECT-E-04-SPL

• Factory tested and assembled cast iron section assembly
• Insulated steel jacket
• Aluminized steel flue collector hood with flue cap on top outlet (convertible to rear outlet)
• Swing away burner mounting door
• Heater opening cover plate
• High limit control with circulator relay and LWCO function
• Electrical junction box with wiring harnesses
• Junction box cover plate with service switch
• (2) vent pipe brackets
• Steam pressure, temperature gauge
• 15 psi ASME relief valve-side outlet
• Drain valve
• Barometric damper
• Siphon
• Gauge glass, cocks and guard

  Weil-Mclain SGO-5-S4

• Allows the installer to size the boiler more closely to the home heating needs for greater efficiency, the lowest firing rate, 0.85 - 87000 BTU, is necessary for many well insulated homes where the heat loss is minimal
• 1" thick pyrolite ceramic fiber combustion chamber, fast warm-up - glows to incandescence in 11 - 17 sec, large diameter allows brushing flue passages without punching through chamber
• S-series operates at 140 psi pump pressure for better fuel atomization, thereby having the ability to tolerate fuel oil with heavy ends
• S-series is standard with a state-of-the-art, solid state ignition system, making it more tolerant to low VAC age or VAC age fluctuations
• Integrated ignition
• Electronic delay with solenoid valve clean-cut fuel pump
• S-series has exceptional water content, the first size has 16 Gallon of water, high water volume and placement of the coil in the hottest part of the boiler allows for maximum coil performance
• The unique tube design of the S-series boiler heat exchanger slows the flue gases, allowing for more effective heat transfer without the need for extreme baffling often seen in other vertical tube boilers
• Each boiler is constructed and hydrostatically tested in accordance with ASME boiler code, the capacity and efficiency are rated in accordance with the standards of the institute of boiler and radiator manufacturers (IBR)
• Built-in air scoop purges air from the system providing a quiet, trouble free hot water heating system without the use of External devices
• Extended flange coil is away from the boiler for easy accessibility, use of ribbed neck carriage bolts eliminates the problems encountered when a weld stud is broken during servicing, large coil plate allows for a greater gasket sealing area
• Extended weld fittings of SA106 Schedule 80 seamless pipe extend beyond the jacket and allow the service technician or homeowner to see small leaks that, if undetected, could later damage the boiler shell and void the warranty
• Easy cleaning and maintenance accessibility to combustion areas and the open tubes make it easy for the service technician to thoroughly clean the boiler
• Flush jacket, altitude, temperature and pressure gauge, ASME relief valve, thankless heater - 3 gpm, factory assembled, wired and packaged, 3450 RPM high-speed flame retention oil burner, interrupted primary ignition, hydronic triple aquastat relay, 007 circulator pump, brass boiler drain valve
• Lifetime limited warranty

Williamson-Thermoflo BB-PMP-210-S2

Weil-Mclain CGA3PIDLS3