|◀ ◀ 697 - 708 of 816 ▶ ▶|
View:

Air Conditioning Condensing Unit Split Thru-The-Wall 2-1/2 Ton 30K 230/1

Features:
  • Factory charged with R-410A refrigerant (charge will need to be field-adjusted)
  • Unique cabinet design - unit side panels fit inside rather than outside the base pan to improve water containment on the sides of the cabinet
  • Extra-high efficiency scroll R-410A compressor
  • high pressure switch
  • Propeller type fan - Moves more air over the condenser coil at lower operating watts than standard squirrel cage type blower
  • Sloped base pan - Positive water drainage from the unit to the building exterior
  • Plastic coated coil guard
  • Filter / drier

    First Company 30WCXA12-AB

    • Item#:
    30WCXA12-AB
    Manufacturer Item:
    75GA3012AM
    Manufacturer:
    FIRST CO.
     
    30WCXA12-AB

    Air Handler Vert/Horiz 20 Ton 208/230/3 72" L x 59-1/2" W x 34-1/2" H

  • CABINETUnit cabinet should be constructed of galvanized, pre-painted steel.
  • MOTORInherently protected motors are mounted inside of insulated cabinet to reduce motor noise. A choice of motor horsepowers and drive combinations are available to allow you to meet specified CFM at various static pressures up to 2" [.498 kPa] External static pressure.
  • LOW PROFILEAllows for horizontal installation in most standard drop ceiling applications, and the movement of units through most standard doorways for addition or replacement work.
  • THERMAL EXPANSION VALVESStandard all models.
  • FILTERSOne inch [25 mm] throwaway filters are standard, but filter racks are designed to accept either one inch [25 mm] or two inch [51 mm] filters.
  • EVAPORATOR COILTwo circuit, interlaced row split coils are constructed with copper tubes and aluminum fins mechanically bonded to the tubes for maximum heat transfer capabilities. All coil assemblies are leak tested up to 450 PSIG [3100 kPa] internal pressure prior to installation into units.
  • REFRIGERANT CONNECTIONSField piping connections are made through a fixed post between two side access panels on either side of the unit. Allows flexibility to meet most field conditions as well as full accessibility after the installation is complete. Units may be used with two straight cool condens ing units or single circuit manifolded in the field using the copper fittings shipped with each unit. The RHGN Air Handler has not been tested, rated or certified to operate with dual residential remote heat pumps.
  • DRAIN PANThe galvanized steel drain pan is designed to trap condensate in either vertical or horizontal installations. Condensate drain connections are located on both sides of the unit allowing complete flexibility to meet most field conditions.
  • SERVICE ACCESSTwo removable panels on top and each side of the unit are easily removed for access to motors, blowers, sheaves, and filters.
  • HORIZONTAL OR VERTICALAll models are designed for either application and can be installed in either position as supplied from the factory.
  • TESTINGAll units are run tested at the factory prior to shipment. Units are shipped with a holding charge of nitrogen.

    Fujitsu RHGL-240ZK

    • Item#:
    RHGL-240ZK
    Manufacturer Item:
    RHGL-240ZK
    Manufacturer:
    FUJITSU(UNITARY)
     
    RHGL-240ZK_Spec

    Air Condition Condenser 20 Ton 240K BTU 230/3 VAC

  • Single stage cooling capacity control on all 072-241 models
  • Two stage cooling capacity control on all 120-240 models
  • Round copper tube aluminum plate fin (RTPF) condenser coils on all models
  • Brass suction and liquid line service valves
  • Full perimeter base rail with built-in rigging adapters and fork truck slots
  • Galvanized steel cabinet with pre-painted exterior panels and primer-coated
  • interior panels tested to 500 hours salt spray protection
  • Fully hermetic scroll compressor with crankcase heater
  • Compressor mounted on independent vibration isolators
  • Comfort AlertTM Diagnostic Board
  • LED Go-No-Go and fault code
  • Built in time guard anti-short cycle
  • Phase protection
  • Fault code retention logic
  • Low volt compressor contactor Protector
  • All units have high and low pressure switches
  • Direct drive permanently lubricated condenser fan motors
  • Newly designed terminal board facilitates simple safety circuit
    troubleshooting and simplified control box arrangement
  • Outdoor temperature cooling operation range up to 125°F (52°C) and down to 40°F (4°C ) using winter start kit
  • Models with optional low ambient control provide cooling operation down to -20°F (-29°C )
  • All units factory run tested

    International Comfort Products CAS241HAA0A00A

    • Item#:
    CAS241HAA0A00A
    Manufacturer Item:
    CAS241HAA0A00A
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    CAS0-ICP-Warranty_Misc
    CAS0-ICP_Install
    CAS0-ICP_Spec

    Air Condition Condenser 20 Ton 240K BTU 230/3 VAC 3-Stage

  • Single stage cooling capacity control on 072 to 121 models, two stage cooling capacity control on 180 to 240 models
  • All models utilize round copper tube, aluminum plate fin condenser coils (RTPF)
  • Brass suction and liquid line service valves
  • Fully hermetic scroll compressors with crankcase heater and suction line accumulators
  • Compressors include overload protection and vibration isolation for further enhancement of
  • quiet operation
  • Comfort AlertTM diagnostic and troubleshooting control system

    LED GoNoGo and fault code

    Built in time guard antishort cycle

    Phase protection

    Fault code retention logic
  • Low volt compressor contactor Protector
  • Full perimeter base rail with built-in rigging adapters and fork truck slots
  • Prepainted exterior panels and primercoated interior panels tested to 500 hours salt spray protection
  • Filter drier standard with each unit (shipped for field installation)
  • Direct drive permanently lubricated condenser fan motors
  • Newly designed terminal board facilitates simple safety circuit
    troubleshooting and simplified control box arrangement
  • All units have high pressure and loss of charge protection
  • Outdoor temperature cooling operation range up to 125°F (52°C) and down to 35°F (2°C )
  • Models with optional low ambient control provide cooling operation down to 20°F (29°C )
  • All units factory run tested

    International Comfort Products CHS243HTA0A00A

    • Item#:
    CHS243HTA0A00A
    Manufacturer Item:
    CHS243HTA0A00A
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    CHS-ICP_Spec
    CHS181-243_Install

    Air Condition Condenser 7-1/2 Ton 90K BTU 230/3 VAC

  • Single stage cooling capacity control on 072 to 121 models, two stage cooling capacity control on 180 to 240 models
  • All models utilize round copper tube, aluminum plate fin condenser coils (RTPF)
  • Brass suction and liquid line service valves
  • Fully hermetic scroll compressors with crankcase heater and suction line accumulators
  • Compressors include overload protection and vibration isolation for further enhancement of
  • quiet operation
  • Comfort AlertTM diagnostic and troubleshooting control system

    LED GoNoGo and fault code

    Built in time guard antishort cycle

    Phase protection

    Fault code retention logic
  • Low volt compressor contactor Protector
  • Full perimeter base rail with built-in rigging adapters and fork truck slots
  • Prepainted exterior panels and primercoated interior panels tested to 500 hours salt spray protection
  • Filter drier standard with each unit (shipped for field installation)
  • Direct drive permanently lubricated condenser fan motors
  • Newly designed terminal board facilitates simple safety circuit
    troubleshooting and simplified control box arrangement
  • All units have high pressure and loss of charge protection
  • Outdoor temperature cooling operation range up to 125°F (52°C) and down to 35°F (2°C )
  • Models with optional low ambient control provide cooling operation down to 20°F (29°C )
  • All units factory run tested

    International Comfort Products CHS091HMA0A00A

    • Item#:
    CHS091HMA0A00A
    Manufacturer Item:
    CHS091HMA0A00A
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    CHS-ICP_Install
    CHS-ICP_Spec

    Air Condition Condenser 15 Ton 180K BTU 230/3 VAC 3-Stage

  • Single stage cooling capacity control on 072 to 121 models, two stage cooling capacity control on 180 to 240 models
  • All models utilize round copper tube, aluminum plate fin condenser coils (RTPF)
  • Brass suction and liquid line service valves
  • Fully hermetic scroll compressors with crankcase heater and suction line accumulators
  • Compressors include overload protection and vibration isolation for further enhancement of
  • quiet operation
  • Comfort AlertTM diagnostic and troubleshooting control system

    LED GoNoGo and fault code

    Built in time guard antishort cycle

    Phase protection

    Fault code retention logic
  • Low volt compressor contactor Protector
  • Full perimeter base rail with built-in rigging adapters and fork truck slots
  • Prepainted exterior panels and primercoated interior panels tested to 500 hours salt spray protection
  • Filter drier standard with each unit (shipped for field installation)
  • Direct drive permanently lubricated condenser fan motors
  • Newly designed terminal board facilitates simple safety circuit
    troubleshooting and simplified control box arrangement
  • All units have high pressure and loss of charge protection
  • Outdoor temperature cooling operation range up to 125°F (52°C) and down to 35°F (2°C )
  • Models with optional low ambient control provide cooling operation down to 20°F (29°C )
  • All units factory run tested

    International Comfort Products CHS183HTA0A00A

    • Item#:
    CHS183HTA0A00A
    Manufacturer Item:
    CHS183HTA0A00A
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    CHS-ICP_Spec
    CHS181-243_Install

    Air Condition Condenser 15 Ton 180K BTU 460/3 VAC 3-Stage

  • Single stage cooling capacity control on 072 to 121 models, two stage cooling capacity control on 180 to 240 models
  • All models utilize round copper tube, aluminum plate fin condenser coils (RTPF)
  • Brass suction and liquid line service valves
  • Fully hermetic scroll compressors with crankcase heater and suction line accumulators
  • Compressors include overload protection and vibration isolation for further enhancement of
  • quiet operation
  • Comfort AlertTM diagnostic and troubleshooting control system

    LED GoNoGo and fault code

    Built in time guard antishort cycle

    Phase protection

    Fault code retention logic
  • Low volt compressor contactor Protector
  • Full perimeter base rail with built-in rigging adapters and fork truck slots
  • Prepainted exterior panels and primercoated interior panels tested to 500 hours salt spray protection
  • Filter drier standard with each unit (shipped for field installation)
  • Direct drive permanently lubricated condenser fan motors
  • Newly designed terminal board facilitates simple safety circuit
    troubleshooting and simplified control box arrangement
  • All units have high pressure and loss of charge protection
  • Outdoor temperature cooling operation range up to 125°F (52°C) and down to 35°F (2°C )
  • Models with optional low ambient control provide cooling operation down to 20°F (29°C )
  • All units factory run tested

    International Comfort Products CHS183LTA0A00A

    • Item#:
    CHS183LTA0A00A
    Manufacturer Item:
    CHS183LTA0A00A
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    CHS-ICP_Spec
    CHS181-243_Install

    Package Gas/Electric 5 Ton 60K BTU Cooling 90K BTU Heating 208/230/1 R410A 52-3/4 x 48-3/16 x 44-1/8

  • Efficient single-stage scroll compressor
  • Efficient multi-speed ECM blower motor
  • Single-stage gas valve
  • Corrosion-resistant stainless steel heat exchanger
  • Reliable, direct spark gas ignition
  • System protecting highand low-pressure switches
  • Wire hail guard grille and raised coil design for protection against weather and debris
  • Corrosion-resistant tin-plated copper evaporator coil tubing
  • Sound reducing features: vibration-reducing top panel, soft mounted compressor and blower motor
  • Compatible thermostat: heat/cool with humidity sensing
  • Rooftop or ground level installation
  • Cooling capacity: 25 tons

    International Comfort Products PGD460090H001K

    • Item#:
    PGD460090H001K
    Manufacturer Item:
    PGD460090H001K
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    PGD4-ICP-Warranty_Misc
    PGD4-ICP_Install
    PGD4-ICP_Spec

    Package Roof Top Heat Pump 2 Ton 14 SEER 208/230/1 R410A Horizontal Medium Heat

  • Environmentally sound R-410A refrigerant
  • Liquid refrigerant filter driers
  • Copper tube/aluminum fin condenser and evaporator coils
  • EASY TO INSTALL AND SERVICE
  • Light weight, compact construction ideal for manufactured housing and residential applications
  • Hand holds built into the unit base pan
  • Compact, fully self-contained, electric cooling unit with horizontal supply and return ducts
  • Easy panel accessibility for maintenance and installation
  • Accessory electric heaters with single point connections
  • Designed to be serviced from both the side and front

    International Comfort Products PHJ424000K000K

    • Item#:
    PHJ424000K000K
    Manufacturer Item:
    PHJ424000K000K
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    PHJ4-ICP-Service_Misc
    PHJ4-ICP_Install
    PHJ4-ICP_Spec

    Package Roof Top Heat Pump 3 Ton 14 SEER 230/1 R410A

  • Environmentally sound R-410A refrigerant
  • Liquid refrigerant filter driers
  • Copper tube/aluminum fin condenser and evaporator coils
  • EASY TO INSTALL AND SERVICE
  • Light weight, compact construction ideal for manufactured housing and residential applications
  • Hand holds built into the unit base pan
  • Compact, fully self-contained, electric cooling unit with horizontal supply and return ducts
  • Easy panel accessibility for maintenance and installation
  • Accessory electric heaters with single point connections
  • Designed to be serviced from both the side and front

    International Comfort Products PHJ436000KTP0A

    • Item#:
    PHJ436000KTP0A
    Manufacturer Item:
    PHJ436000KTP0A
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    PHJ4-ICP-Service_Misc
    PHJ4-ICP_Install
    PHJ4-ICP_Spec

    Package Heat Pump Unit 2-1/2 Ton 30K BTU 14 SEER

  • REFRIGERATION CIRCUIT
  • Environmentally balanced R- 410A refrigerant
  • Copper tube/aluminum fin condenser and evaporator coils
  • Scroll compressor standard on all models
  • Short- cycling protection for the compressor is built into the defrost control board
  • Dehumidification mode (airflow reduction) on all models
  • EASY TO INSTALL AND SERVICE
  • Installs easily on a rooftop or at ground level
  • Easy three- panel accessibility for maintenance and installation
  • Easily converts to down discharge applications
  • Combination electric heating and cooling

    International Comfort Products PHD430000K000K

    • Item#:
    PHD430000K000K
    Manufacturer Item:
    PHD430000K000K
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    PHD4-ICP-Service_Misc
    PHD4-ICP_Install
    PHD4-ICP_Spec

    Package Heat Pump Unit 3 Ton 14 SEER 230/1

  • REFRIGERATION CIRCUIT
  • Environmentally balanced R- 410A refrigerant
  • Copper tube/aluminum fin condenser and evaporator coils
  • Scroll compressor standard on all models
  • Short- cycling protection for the compressor is built into the defrost control board
  • Dehumidification mode (airflow reduction) on all models
  • EASY TO INSTALL AND SERVICE
  • Installs easily on a rooftop or at ground level
  • Easy three- panel accessibility for maintenance and installation
  • Easily converts to down discharge applications
  • Combination electric heating and cooling

    International Comfort Products PHD436000K000F

    • Item#:
    PHD436000K000F
    Manufacturer Item:
    PHD436000K000F
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    PHD4-ICP-Service_Misc
    PHD4-ICP_Install
    PHD4-ICP_Spec
    |◀ ◀ 697 - 708 of 816 ▶ ▶|
    View: