Bosch BVA-60WN1-M18 Air Handler

• 5 Ton 15 SEER Multi-Position Factory Installed TXV
• Multi-speed ECM blower motor.
• Factory-installed TXV metering.
• Multi-position Installation - upflow or horizontal right standard;
• field convertible to horizontal left or downflow.
• Multiple electrical entry locations.
• Field-installed electric heater kits 5, 7.5, 10, 15, 20KW available as an accessory.
• Dual front panel design for ease of maintenance.
• Blower and coil easy slide out for ease of maintenance.
• Fully-insulated cabinet design.
• Horizontal and vertical condensate drain pans standard.
• Condensate drain pan is polymer with UVC inhibitor.
• Primary and secondary condensate drain fittings.
• Factory-sealed cabinet certified to achieve 2% or less air leakage rate at 1.0" water column.
• Integrated filter rack with tool-less door access.
• AHRI and ETL Listed.,
  
  

Nortek B5BM-x48K-C Polyester Urethane Galvanized Steel Residential System Air Handler with TXV Metering, 48000 BTU, 4 Ton, 30 kw, 208 - 230 VAC

10 years all parts warranty
• Durable, attractive cabinet - designed using Galvanized steel, the door is also Galvanized steel, with a polyester urethane finish, the 950 hr salt spray finish resists corrosion 50% better than comparable units, the plastic drain pan is corrosion-resistant
• Multi-speed gives flexibility of installation
• Ease-of-service - plug-in wire connections and built-in filter rack makes the air handler easy to service
• Circuit board - incorporating blower time delay relay, low Voltage terminal strip and heat-strip sequencing
• Air handler control board - controls time-sequencing of heat stages with field-selectable sequence timing
• Breaker accessibility - breaker accessible from front of unit when heater is applied
• No fasteners on sides or back - smooth surfaces for ease of installation
• 1" insulation with an R-value of 4.2 contributes to quiet operation and prevents cabinet sweating in difficult applications
• Design series
• PSC, 3-speed motor
• 10 x 10" blower
• 12-7/8 x 21" supply air outlet
  
  

  B5BM-X48K-C

Space Pak ESP2430JH4 Grey Direct Expansion Hydronic Evaporator Fan Coil with TXV, 24000 - 30000 BTU, 2 - 2.5 Ton, 230 VAC

High efficiency ECM blower motor
• Easy field adjustable motor staging
• Heat pump compatible
• Anti-frost control
• Integrated control board
• 6-rows copper or aluminum evaporator coil
• Sweat type refrigerant connections
• Float switch
• Condensate trap
• Mold resistant primary drain pan
• Anti-vibration foam strips
• 6" width x 10" diameter wheel
• 7/8" bottom water in and top water out
• 3/4" NPT condensate drain, 15" diameter return inlet
• J series
  
  

  Space Pak ESP2430JH4

Space Pak ESP3642JH4 Grey Direct Expansion Hydronic Evaporator Fan Coil with TXV, 36000 - 42000 BTU, 3 - 3.5 Ton, 230 VAC

High efficiency ECM blower motor
• Easy field adjustable motor staging
• Heat pump compatible
• Anti-frost control
• Integrated control board
• 6-rows copper or aluminum evaporator coil
• Sweat type refrigerant connections
• Float switch
• Condensate trap
• Mold resistant primary drain pan
• Anti-vibration foam strips
• 6" width x 10" diameter wheel
• 7/8" bottom water in and top water out
• 3/4" NPT condensate drain, 15" diameter return inlet
• J series
  
  

  ESP3642JH4

1-1/2 thru 4 tons

Available for environmentally balanced R-410A systems

Factory installed piston metering device with Teflon ring

Sweat connections

Aluminum Tube, Aluminum Fin Evaporator

Primary and secondary drain fittings with brass inserts

Multiple electrical entry locations

Time delay relay (TDR)

Field installed heater packages from 5 kW - 30 kW available separately

HUD approved for manufactured housing

208/230-1-60 supply voltage

Assembled at the factory compliant with low leak requirements of less than 2% cabinet leakage rate at 0.5 inches W.C. and 1.4% cabinet leakage rate at 0.5 inches W.C. when tested in accordance with ASHRAE 193 standard.

1 inch thick insulation with R value of 4.2

Multiposition installation - upflow or horizontal left standard, horizontal right with minor modification (field convertible to downflow with available accessory kit)

No Heat (Plug) Kit factory installed

Filter (washable) available as accessory

ECM 5-speed motor

Low voltage circuit protective fuse (3amp) inline on wire harness

Fujitsu FH4821TPSASN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections

48K BTU 4 Ton
• 115/1 VAC
• 21" Wide
• PSC Motor
• Multi-Position,
  FUJITSU FH4821TPSJSN
  
  

  FUJITSU FH4821TPSJSN

Features

Horizontal application only

Accessory field-installed electric heat kits available in 3, 5, 6, 7.5, or 10 kW

40 VA 208/230-1-60 supply voltage

All Models use R-410A TXV metering device

All Aluminum coils

Adjustable condensate drainpan

FMC4X & FMC4Z

Horizontal return applications require field fabricated bottom cover or solid access panel accessory kit

Cabinets meet the requirement of 1.4% cabinet leakage rate when texted to ASHRAE Standard 193

Cabinets constructed to prevent cabinet sweating

Refrigerant lines and electrical connections can be run out the back or side of casing

PSC motor on all FMU4X & FMC4X models

ECM motor on all FMU4Z & FMC4Z models

Easy to Install and Service

A-coil design for maximum surface area

Multiple electrical, refrigerant lineset and drain line entry for application flexibilty Primary and secondary drain connections exit from the back or side of the cabinet.

Supports furred-down ceiling open return and ducted return applications

Sweat connections for long term reliability

Grooved aluminum tube / aluminum fin coils on FMU4X &

FMC4X models with "AL" in the 10th and 11th position of model number

International Comfort Products FMC4Z3600AL

Fujitsu FH2417TTSJSN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections

• 24K BTU 2 Ton
• 208/230/1 VAC
• 17" Wide
• Multi-Position,
  ,
  
  
  

  FH2417TTSJSN

Fujitsu FH4821TPSASN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections

48K BTU 4 Ton
• 115/1 VAC
• 21" Wide
• PSC Motor
• Multi-Position,
  

Fujitsu FH3617TTSJSN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections

FH3617TTSJSN

Fujitsu FH4821TPSASN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections

48K BTU 4 Ton
• 208/230/1 VAC
• 21" Wide
• Multi-Position,
  
  

  FUJITSU FH4821TTSJSN