Fujitsu FH6024TTSJSN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections

Fujitsu FH6024TTSJSN

Fujitsu A/C Parts K9375720384 Evaporator AUU**

Fujitsu A/C Parts K9375720384

REFRIGERATION CIRCUIT

Copeland Scroll compressors on all models

Suction line accumulator factory installed

Biflow filterdrier included for field installation

Integrated solid state control with TimeTemperature Defrost

High and Low pressure switches

Copper tube / aluminum fin coil EASY TO INSTALL AND SERVICE

Easy Access service valves on all models

External high and low refrigerant service ports

Only two screws to access control panel

Factory charged with R410A refrigerant BUILT TO LAST

Bakedon powder coat finish over galvanized steel

Postpainted (black) coil fins

Coated, weatherresistant cabinet screws

Coated inlet grille with 3/8 (10mm) grille spacing for extra protection

International Comfort Products NXH618GKP

RectorSeal NS-UNI 10PK Novent Universal Refrigerant Cap Silver 1/4" 10 Pack

NS-UNI 10PK

The ND Damper is constructed using Heavy Duty 0.80 extruded aluminum.

Nylon Bearings for quiet operation.

Overlapping parallel blade design insures low leakage.

Designed to operate at static pressures up to 1.5 w.c.

The UL Listed Motor Actuator is a 24 vac 3 wire power open/ power close type.

The motor actuator is rated at 18lbs. of torque. Superior to low torque Spring type motors.

The Motor Actuator housing has a NEMA1 Rating.

Integrated End-Stop Adjustment allows for a percentage of Relief Air (Leakage) to be set when the damper is powered to closed and/or you may set a maximum open position as well.

Bright green and red LEDs Indicate damper open and closed position.

EWC Controls ND-24X10

Make sure you ask for and use genuine Copleand parts. Copeland parts fit right, first time. Insisting on genuine Copeland parts will keep your refrigeration & A/C Compressor running reliably for the long haul

Copeland Parts N03036438

The ND Damper is constructed using Heavy Duty 0.80 extruded aluminum.

Nylon Bearings for quiet operation.

Overlapping parallel blade design insures low leakage.

Designed to operate at static pressures up to 1.5 w.c.

The UL Listed Motor Actuator is a 24 vac 3 wire power open/ power close type.

The motor actuator is rated at 18lbs. of torque. Superior to low torque Spring type motors.

The Motor Actuator housing has a NEMA1 Rating.

Integrated End-Stop Adjustment allows for a percentage of Relief Air (Leakage) to be set when the damper is powered to closed and/or you may set a maximum open position as well.

Bright green and red LEDs Indicate damper open and closed position.

EWC Controls ND-16X10

Make sure you ask for and use genuine Copleand parts. Copeland parts fit right, first time. Insisting on genuine Copeland parts will keep your refrigeration & A/C Compressor running reliably for the long haul

Copeland Parts N03761265

Henry Technologies S-5585 Oil Separator 5/8" OD

Henry Technologies S-5585

JB Industries SHLD-G4 Locking Refrigerant Cap 1/4" R22 4 PK

SHLD-G4

The TB6980/TB7980 digital thermostats provide proportional plus integral individual space temperature control in zoned commercial HVAC systems such as hydronic and pressure dependent VAV with or without reheat. There are four different models:

Depending on the models, the thermostat can have up to three outputs for the following applications:

Floating or Modulating damper/valve actuator control

Damper/valve actuator control with duct reheat and auxiliary heat (B models only)

Hydronic systems (room control, perimeter heating and cooling) Accessories

R841 family of electromechanical relays

T7770A3002 remote room sensor

50014156-002 remote room sensor

32004800-001 bare thermistor

50014157-001 duct temperature sensor

TB6980A1007

All products are designed and manufactured for use within forced air systems, providing effective distribution of conditioned air from the air handler to every room of a residence.Metal duct and fittings are constructed from hot-dipped Galvanized steel. All metal products are made true to gauge. Sheet metal duct, pipe, and fittings are designed with industry and regional standards in mind, as well as ACCA and SMACNA recommendations and requirements. Products are hand-crafted to reduce noise and friction and constructed to maximize efficiency by increasing airflow without leaks. The quality of our Galvanized steel allows us to create fittings that are rust-resistant and durable

Southwark 1135