Hart & Cooley HC65920X12 White Return Air Filter Grille 20" x 12" All-Steel construction 1/3"

White Rodgers Cooling Controls D14-36 Filter Drier Block High Acid Removal

D14-36

Industry Standard R-410A Refrigerant

Models featuring Electric Heat without Indoor Cooling Coil

Quiet and efficient X-13 (ECM) motor technology

Only 35" tall and 4-way convertible for all those tight spaces

Available from factory in upflow and horizontal configurations

Nominal airflow up to 0.5" external static pressure with reduced airflow up to 1.0" external static pressure

Factory installed MultiFlex coils

Sturdy steel construction with 1 inch [25.4 mm] of foil faced insulation for excellent sound and insulating characteristics

Permanent, easily accessible and washable filter furnished standard

Circuit breaker (standard on units with more than 11 kW) meets U.L. and cUL requirements for service disconnect

Factory installed auxiliary electric heat provides exact heat for indoor comfort over a variety of applications

Fan settings for selectable, customized cooling airflow over a wide variety of applications

Cabinet air leakage less than 2% at 1 inch H2O when tested in accordance with ASHRAE standard 193

Fujitsu FH6024TTSJSN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connectionsFujitsu FH6024TTSJSN

Fujitsu A/C Parts K9375720384 Evaporator AUU**

Copeland Parts N03036438 Potential Relay

Copeland Parts N03761265 Potential Relay 120/130 V Pick-Up, 15/40 VAC Drop Out, 130 VAC

RectorSeal NS-UNI 10PK Novent Universal Refrigerant Cap Silver 1/4" 10 Pack

Henry Technologies S-5585 Oil Separator 5/8" OD

JB Industries SHLD-G4 Locking Refrigerant Cap 1/4" R22 4 PK

The TB6980/TB7980 digital thermostats provide proportional plus integral individual space temperature control in zoned commercial HVAC systems such as hydronic and pressure dependent VAV with or without reheat. There are four different models:

Depending on the models, the thermostat can have up to three outputs for the following applications:

Floating or Modulating damper/valve actuator control

Damper/valve actuator control with duct reheat and auxiliary heat (B models only)

Hydronic systems (room control, perimeter heating and cooling) Accessories

R841 family of electromechanical relays

T7770A3002 remote room sensor

50014156-002 remote room sensor

32004800-001 bare thermistor

50014157-001 duct temperature sensor

TB6980A1007

All products are designed and manufactured for use within forced air systems, providing effective distribution of conditioned air from the air handler to every room of a residence.Metal duct and fittings are constructed from hot-dipped Galvanized steel. All metal products are made true to gauge. Sheet metal duct, pipe, and fittings are designed with industry and regional standards in mind, as well as ACCA and SMACNA recommendations and requirements. Products are hand-crafted to reduce noise and friction and constructed to maximize efficiency by increasing airflow without leaks. The quality of our Galvanized steel allows us to create fittings that are rust-resistant and durable.