Surge protectors are designed to protect your equipment by dissipating momentary Voltage spikes and transient power surges. Suitable for use on a circuit capable of delivering not more than 10000 rms symmetrical amp, 240 VAC max, when protected by a circuit breaker rated 30 amp maximum and 240 VAC minimum.

Easy installation
• Low cost, high performance
• Rugged, reliable
• 3/4" conduit connection
• Green light indicates surge suppression present
• Installation point - electrical panel, inside electrical disconnect
  
  

  ICM516

SPECIFICATIONS

Inputs: L1 & L2

Nominal voltage: 120 VAC, 240 VAC

Over voltage limits: 120 VAC nominal = 140 VAC 240 VAC nominal = 250 VAC

Under voltage limits: 120 VAC nominal = 95 VAC 240 VAC nominal =195 VAC

Outputs: Compressor

Current: Maximum nominal = 9 A, 16A Absolute maximum = 22 FLA, 84 LRA

Over current limits: ICM870-9A = 11.25A, ICM870-16A = 20A

Operating temperature: -40°F to 131°F (-40°C to 55°C)

Storage temperature: -40°F to 149°F (-40°C to 65°C)

Humidity: 0-95% non-condensing

Enclosure: IP65/Type 4X

Dimensions: 7.63 x 3.19 x 2.13

ICM Controls ICM870-16A

The ICM492 constantly monitors line Voltage and protects single-phase equipment against low and high Voltage conditions, and rapid short cycling due to Voltage fault or power interruption. Its easy-view, backlit Digital display makes it user friendly to read and monitor Voltage conditions, and adjust parameters to meet specific needs.

Protects against over and under Voltage and rapid short cycling caused by transient faults and power interruptions
• Easy view, backlit Digital display
• RMS Voltage set point
• Adjustable Voltage set point
• Adjustable over Voltage setting
• Adjustable under Voltage setting
• Adjustable anti-short cycle time delay
• Adjustable response time
• Control mode
• Universal line Voltage input
• Heavy duty SPDT relay output
• Universal control Voltage input (for integrating a thermostat)
  
  

  ICM Controls ICM492C

ICM Controls ICM333 Dual Input Head Pressure Control 35-465 PSI

ICM333

ICM Controls ICM450A Line Voltage Monitor, Manual or Automatic Reset

ICM Controls ICM450A

Features

Protects against over and under voltage, rapid short cycling caused by transients, and high-power surges

Ideal for mini-splits or other condensing units

Easy to view, backlit digital display

Bank of five L-L surge arresters

Built-in 60A contactor

NEMA Type 3R rated metal enclosure

Easy installation and setup

ICM Controls ICM493-60A

ICM Controls ICM302 Defrost Control Board, 18 - 30 VAC , 1 amp Normally Open, 50 - 60 Hz

Low cost, time and temperature defrost
• Time and temperature terminate
• 30/60/90 min pin-selectable intervals time
• Test pins reduce test time by 256x
• High power output (1 HP at 240 VAC )
• Integral short cycle protection
• 5 min anti-short cycle time
• 30/60/90 min interval times
• SPST relay
• Direct replacement for Nordyne 621301A/621579B/621579C/917178, ICM DFORB-AB1004
• 10 min fixed defrost time
  
  

  ICM302

ICM Controls ICM493 Line Voltage Monitor with Built-In Surge Suppression, An advanced, single phase line Voltage monitor with a bank of surge arresters for added protection against lightning strikes. Includes a built-in 40A contactor. Ideal for Mini-Splits or other valuable, single phase equipment. Protects against over and under Voltage, rapid short cycling caused by transients, and high-power surges. Easy to view, backlit Digital display. NEMA-rated 3R enclosure for outdoor use, Easy installation and setup

ICM493

ICM Controls ICM441C 3-PH Line Voltage Motor Protector, 90 - 140 VAC (RMS) and 185 - 270 VAC (RMS) Replaces Part #:'s : 071-0376-01 | 071-0376-02 | 071-0397-00 | 071-0397-01 | 071-0424-00 | 071-0424-01 | 071-9800-01 | 071-9800-02 |

ICM Controls ICM441C

ICM Controls ICM408C-8 Phase Monitor

190-480 VAC 3,8 Pin



ICM408C-8

Sealed Unit Parts Linebacker Lbs.K10 2-Pole Surge Protector, 120 - 240 VAC , 10 kilo-amp Nominal Discharge The Lbs.K10 uses state-of-the-art TPMOV technology coupled with the ability to remove your equipment from damaging surges, the Lbs.K10 provides the ultimate solution for you surge protection needs.

• NO/NC relay to disconnect equipment and/or activate indicator
• Easy installation at condensing unit
• Green LED indicates surge protection status
• 4x style weatherproof housing
• TPMOV technology
• Surface mount
• NEMA 3R plastic enclosure
• (2) 18 AWG wires + ground The Lbs.K10 uses state-of-the-art TPMOV technology coupled with the ability to remove your equipment from damaging surges, the Lbs.K10 provides the ultimate solution for you surge protection needs
  
  

  LBK10

Sealed Unit Parts OV42 Universal Replacement Overload, 1/6 - 1/4 HP at 120 VAC , 1/4

OV42