STANDARD FEATURES

Refrigerant leak detection dissipation system for added safety

Multi-tap ECM (electronic commutating motor) motors  all sizes.

Integrated motor controls, with 90-sec off TDR function, have replaced integrated circuit board.

Five available speed tags to meet a wide range of applications.

Large, grooved tube, louvered fin coils.

Efficient, quiet, time-tested blower housings and diffusers.

Sturdy, drainable condensate pans.

Construction innovations designed to prevent cabinet sweating.

Tested for condensate disposal in much tougher conditions than Air Conditioning and Refrigeration Institute requirements.

Super-thick R-4.2 insulation with vapor barrier.

Pre-painted galvanized steel cabinet (dark grey).

Design meets stringent regulations for cabinet air leakage of less than 2% when tested at 0.5 inches W.C., and less than 1.4% at 0.5 inches W.C. when tested in accordance with ASHRAE 193 standard.

Installation-flexible, multipoise units. 2-piece modular design available for 42 thru 60 sizes. Facilitates attic and crawlspace installations..

Horizontal hanging provisions on cabinet.

Newly improved filter rack area filter door insulation added for improved air seal. No tools required to access filter.

3 through 30 kW accessory heaters - field installed.

Easy plug-in provisions for heater installation.

Entry options for high and low voltage wiring hook-up.

Leak-preventing sweat connections.

Factory installed thermostatic expansion valve, TXV, on all coils.

Designed for manufactured housing applications

MULTIFAMILY CEILING MOUNT FAN COIL

FMU5Z and FMC5Z 1-1/2, 2, 2-1/2, and 3 Tons

Horizontal application only

Accessory field-installed electric heat kits available in 3, 5, 6, 7.5, or 10 kW

40VA, 208/230V-1-60 transformer

All models use Puron Advance, R-454B refrigerant and have a hard-shutoff TXV metering device

Adjustable condensate drain pan FM(C,U)5X, FM(C,U)5Z

Horizontal return applications require field fabricated bottom cover

Cabinets meet the requirement of 1.4% cabinet leakage rate when tested to ASHRAE Standard 193

Cabinets insulated to prevent cabinet sweating

Refrigerant lines and electrical connections can be run out the back or side of casing Performance

PSC motor on all FMU5X & FMC5X models

ECM motor on all FMU5Z & FMC5Z models Easy To Install Service

A-coil design for maximum surface area

Multiple electrical, refrigerant lineset and drain line entry for application flexibility

Primary and secondary drain connections exit from the back or side of the cabinet

Supports furred-down ceiling open return and ducted return applications

Sweat connections for long term reliability

Grooved aluminum tube / aluminum fin coils on FMU5X, FMC5X, FMC5Z, and FMU5Z models with AL in the 10th & 11th position

MULTIFAMILY CEILING MOUNT FAN COIL

FMU5Z and FMC5Z 1-1/2, 2, 2-1/2, and 3 Tons

Horizontal application only

Accessory field-installed electric heat kits available in 3, 5, 6, 7.5, or 10 kW

40VA, 208/230V-1-60 transformer

All models use Puron Advance, R-454B refrigerant and have a hard-shutoff TXV metering device

Adjustable condensate drain pan FM(C,U)5X, FM(C,U)5Z

Horizontal return applications require field fabricated bottom cover

Cabinets meet the requirement of 1.4% cabinet leakage rate when tested to ASHRAE Standard 193

Cabinets insulated to prevent cabinet sweating

Refrigerant lines and electrical connections can be run out the back or side of casing Performance

PSC motor on all FMU5X & FMC5X models

ECM motor on all FMU5Z & FMC5Z models Easy To Install Service

A-coil design for maximum surface area

Multiple electrical, refrigerant lineset and drain line entry for application flexibility

Primary and secondary drain connections exit from the back or side of the cabinet

Supports furred-down ceiling open return and ducted return applications

Sweat connections for long term reliability

Grooved aluminum tube / aluminum fin coils on FMU5X, FMC5X, FMC5Z, and FMU5Z models with AL in the 10th & 11th position

Fujitsu FH3621TPSJSN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections

Fujitsu FH3621TPSJSN

Fujitsu FH6021TTSJSN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections

FH6021TTSJSN