Hart & Cooley 10REA45 B-Vent 45 Degree Elbow 10" Natural Gas Aluminum

Hart & Cooley 10REA45

Hart & Cooley 0.012" Aluminum Inner and 0.018" G90 Galvanized Steel

• Deep locking groove assures solid joint and secure lock
• Corrosion resistant aluminum inner wall for rapid warm-up
• Unique locking band provides 360 deg turning radius of the pipe and fittings
• Locking band slides over tabs easily, locks firmly without twisting
• Locking tabs hold pipe securely together, can be easily unlocked
• Positive stop provides proper alignment and positive fit for mating end of pipe or fitting
• Reinforced ends curled bead on end of outer pipe for rigidity and strength
• The allowable minimum clearance to combustibles is 1"
• A full set of installation instructions are supplied with caps and supports Hart & Cooley 10RP3 B-Vent Pipe 10" x 36" Natural Gas Aluminum Inner & Galvanized Steel Outer,

  Hart & Cooley 8RT8

The Direct Vent System provides through-the-wall venting for Thermo Price and Spirit Furnaces models. Its the perfect solution when chimney venting is not an option, such as having an old un lined chimney in your home, or no chimney at all. The direct vent provides an outlet for exhaust gasses as well as an intake for combustion air through a single exterioir wall terminal. It is also a quiet non-powered device; it does not need a noisy fan to vent the air from your furnace. This system is applicable with either a Beckett or Riello burner.,

Thermo Products Parts AOPS8393

Thermo Pride AOPS8394 Sidewall Vent Accessory Kit for VHF-ABP Oil Furnace,

Thermo Products Parts AOPS8394

Thermo Pride AOPS7544 Concentric Vent Kit for Down Flow and Direct Vent Furnace

Thermo Products Parts AOPS7544

Venti Air CONVENT-3 Concentric Vent Kit 3"

Venti Air CONVENT-3

Venti Air CONVENT-2 Concentric Vent Kit 2"

Venti Air CONVENT-2

The DiversiTech CVENT-2 is a 2 in. concentric termination kit that simplifies installation for high efficiency furnances by only requiring one hole through the wall or roof where the pipes terminate. Without using the kit the installation would require cutting two holes through the home (one for each pipe). The kit includes combustion air inlet cap, air inlet pipe, vent pipe and intake/vent concentric Y.

Diversitech CVENT-2

The DiversiTech CVENT-2 is a 3 in. concentric termination kit that simplifies installation for high efficiency furnances by only requiring one hole through the wall or roof where the pipes terminate. Without using the kit the installation would require cutting two holes through the home (one for each pipe). The kit includes combustion air inlet cap, air inlet pipe, vent pipe and intake/vent concentric Y.

Diversitech CVENT-3

All Fas-n-Seal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on Fas-n-Seal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All Fas-n-Seal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

M & G Duravent FSAAU3

All Fas-n-Seal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on Fas-n-Seal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All Fas-n-Seal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

M & G Duravent FSAAU4

All Fas-n-Seal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on Fas-n-Seal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All Fas-n-Seal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

M & G Duravent FSWT3