All field vent hoods are made of heavy gauge aluminum and can be used with natural gas, LP gas or oil-fired equipment. There are five diameters ranging from 3 to 8 Inch. The concentric pipe, angled outlet deflectors, and spaced plate design allow for better heat dissipation. This type of construction minimizes the effects of heat on the outside wall. The angled hood design reduces the effects of wind on the venting system. The inner and outer pipe are a continuous structure. This allows for easy installation to power venter or vent pipe and also eliminates possible positive pressure leaks in the wall section.

• Can be used in conjunction with PVG and PVO power venters or with forced draft systems
• 7-5/8 x 7-5/8 shield for 0 clearance to combustible
• Designed for standard vent pipe and Class B type double-wall (B-Vent) connection
• Provides proper clearance between flue gas stream and wall combustible

Outstanding Performance:
This damper was specifically designed with R8 insulation specification in mind to contribute to energy savings and help the system pass efficiency audits. Best of all, it helps eliminate hot and cold spots, the biggest cause of callbacks. The improved internal design creates a slower return that ensures a quiet operation.
Installation Made Easy
For fast, accurate installation with no callbacks, the TrueZONE Damper has you covered with a range of features that simplify installation in most applications:

Adjustable Range Stops  Easy to understand and set by utilizing a pushin lever. Theyre used to bleed air into the zones which helps lower pressure and reduce noise.

Push-In Terminals  The same easy wiring design used on TrueZONE Panels. No tools needed, has space for two wires.

Taping Flange  Lets you position insulation under it before sealing with foil tape.

Mechanical Position Indicator  Easy viewing through a clear window.

LED Indicator Lights  Red indicates the damper is closed and green indicates open (used in 3-wire applications)

Honeywell ZD10X12TZ

The ND Damper is constructed using Heavy Duty 0.80 extruded aluminum.

Nylon Bearings for quiet operation.

Overlapping parallel blade design insures low leakage.

Designed to operate at static pressures up to 1.5 w.c.

The UL Listed Motor Actuator is a 24 vac 3 wire power open/ power close type.

The motor actuator is rated at 18lbs. of torque. Superior to low torque Spring type motors.

The Motor Actuator housing has a NEMA1 Rating.

Integrated End-Stop Adjustment allows for a percentage of Relief Air (Leakage) to be set when the damper is powered to closed and/or you may set a maximum open position as well.

Bright green and red LEDs Indicate damper open and closed position.

EWC Controls ND-16X10

The ND Damper is constructed using Heavy Duty 0.80 extruded aluminum.

Nylon Bearings for quiet operation.

Overlapping parallel blade design insures low leakage.

Designed to operate at static pressures up to 1.5 w.c.

The UL Listed Motor Actuator is a 24 vac 3 wire power open/ power close type.

The motor actuator is rated at 18lbs. of torque. Superior to low torque Spring type motors.

The Motor Actuator housing has a NEMA1 Rating.

Integrated End-Stop Adjustment allows for a percentage of Relief Air (Leakage) to be set when the damper is powered to closed and/or you may set a maximum open position as well.

Bright green and red LEDs Indicate damper open and closed position.

EWC Controls ND-24X10

Internatinoal Comfort Procusts

Zone Damper

Slip-In

Bottom Mount

10 x 16

3 Wire

International Comfort Products DAMPSLB10X16-B

Internatinoal Comfort Procusts

Zone Damper

Slip-In

Bottom Mount

10 x 14

3 Wire

International Comfort Products DAMPSLB10X14-B

International Comfort Products Fast Parts DAMPSLB10X24-B Zone Damper Slip-In Bottom Mount 10" x 24"

International Comfort Products Fast A/C Parts DAMPSLB10X24-B