Malco C-RHEx MSHMLC Cleanable Reversible Dual Side Magnetic Hex Driver, Quickly change between 1/4 and 5/16" hex sizes with Malcos unique, exclusive, dual-sided magnetic hex drivers. The reversible hex socket fits over a 1/4" magnet-tipped, ball locking hex shaft, and can be quickly reversed to change sizes. Eliminate troublesome buildup of metal shavings in the hex tip with the easy clean magnet. Just swipe with a glove or shop towel to clear any metal shavings. Tested torque of the reversible hex chuck driver design is equal to one-piece drivers.,

Malco MSHMLC

,

MSHMLC

Malco C-RHEx MSHLC Cleanable Reversible Dual Side Magnetic Hex Driver, Quickly change between 1/4 and 5/16" hex sizes with Malcos unique, exclusive, dual-sided magnetic hex drivers. The reversible hex socket fits over a 1/4" magnet-tipped, ball locking hex shaft, and can be quickly reversed to change sizes. Eliminate troublesome buildup of metal shavings in the hex tip with the easy clean magnet. Just swipe with a glove or shop towel to clear any metal shavings. Tested torque of the reversible hex chuck driver design is equal to one-piece drivers.,

Malco MSHLC

Specially angled ground tip easily punctures and rips duct to the desired length starting hole. Hardened tip is ground on both sides to create 2 cutting edges for long, useful life. Cutting edges are aligned with shaft flats for large striking surfaces. Corrosion resistant blade, cushioned grip and a hang hole for storage complete this handy tool.

• Works with the TurboShear

Sid Harvey Item #:CDR: Replaces Part #:'s : 40949,

CDR

,

CDR

Malco DS1 Anodized Aluminum Duct Stretcher, 16" OAL

• Use the duct stretcher to hold duct in place with 1 hand while slipping drive cleat in place with other hand
• The low profile, straight body is designed to go anywhere, even in the tightest quarters
• Additional spacing holes allow wheels to be adjusted to span greater distances
• Rugged anodized aluminum body features large vinyl cushion grip and handy hang-up hole,
  
  

  T646-5

  ,
  

  T646-5

Hex corners of keys are sharp and clean. Finish is black oxide. Smooth zinc plated case can be used as handle for extra leverage. Flat spring holds keys in any work position.

• 3/32, 7/64, 1/8, 9/64, 5/32, 3/16, 7/32, 1/4" Hex Key

,

W48-MALCO

,

W48-MALCO

Built-in wire cutter lets you finish the job you started with just one tool! double edged blade cleanly pierces through outer skin and insulation. Cuts from either direction around entire circumference of duct. Fine honed blade is long lasting stainless steel. Wire cutter cuts hardened wire rib coil. Compound leverage, for easy wire cutting. comfortable, non-slip vinyl gripped handles.

• Built-in wire cutter
• Double edged blade
• Cuts from either direction
• Fine honed blade
• 10.4 to 1 - 11.9 to 1 wire cutter variable leverage ratio (high/low) throughout stroke

,

Malco T671-2

,

T671-2

Malco W29 Black Oxide Folding Hex Key Set, 9 Pieces

• Folds up like a knife, stores easily, eliminates lost keys
• Sturdy case can be used as a handle for extra leverage to apply torque

Sid Harvey Item #:T650-1: Replaces Part #:'s : T650,

T650-1

,

T650-1

Malco 12F Folding Tool 12",

12F

,

12F

Malco 18F Folding Tool, 22 ga Sheet Metal, 18" L

• Folding tool seams are formed from two steel halves, permanently joined together
• Handy sight holes assure proper depth alignment

,

Malco 18F

,

18F

Malco 12F Folding Tool, 22 ga Sheet Metal, 12" L

• Folding tool seams are formed from two steel halves, permanently joined together
• Handy sight holes assure proper depth alignment

Sid Harvey Item #:T646-3: Replaces Part #:'s : 13019,

Malco T646-3

,

T646-3

Malco 24F Folding Tool, 24" L

• Folding tool seams are formed from two steel halves, permanently joined together
• Handy sight holes assure proper depth alignmentSid Harvey Item #:T646-3B: Replaces Part #:'s : 13044,
  
  

  Malco T646-3B

  ,
  

  T646-3B

All products are designed and manufactured for use within forced air systems, providing effective distribution of conditioned air from the air handler to every room of a residence.Metal duct and fittings are constructed from hot-dipped Galvanized steel. All metal products are made true to gauge. Sheet metal duct, pipe, and fittings are designed with industry and regional standards in mind, as well as ACCA and SMACNA recommendations and requirements. Products are hand-crafted to reduce noise and friction and constructed to maximize efficiency by increasing airflow without leaks. The quality of our Galvanized steel allows us to create fittings that are rust-resistant and durable.

Malco D6AS