• Transformer powers low voltage control systems and provides overload protection
• Low voltage terminal board provides convenient connections for thermostat and heating and cooling equipment wiring
• Mounts on standard 4 x 4" junction box
• Relay is easily replaced without disturbing wiring

HONEYWELL R8285D5001

HONEYWELL R8285D5001

• With 45 sec safety timing and alarm outputs
• Provides automatic, nonrecycling control of an intermittent ignition oil burner system
• Controls oil burner, oil valve (if desired) and the ignition transformer in response to a call for heat
• Solid state flame sensing circuit
• Enclosed safety switch with external reset button
• Manual trip lever opens safety switch for system maintenance
• Mounts on standard 4 x 4" junction box, select models may be mounted directly on burner housing
• C554A cadmium sulfide flame detector and 24 VAC thermostat required
• 75 VA at 120/240 VAC, 50-60 Hz, 25 VA at 24V, 50-60 Hz alarm load ratings(pilot duty)

R75-44

R75-44

• Controls oil burner, oil valve (if desired) and the ignition transformer in response to a call for heat
• Solid state flame sensing circuit
• LED on terminal strip indicates system lockout
• Remote lockout indication
• Enclosed safety switch with external reset button
• Manual trip lever opens safety switch for system maintenance
• Mounts on standard 4 x 4" junction box
• C554A cadmium sulfide flame detector and 24 VAC thermostat required
• With 15 sec safety timing, alarm outputs and manual safety switch

honeywell r75-40

honeywell r75-40

• Operates the oil burner and oil valve (if desired) in response to a call for heat from a low voltage control circuit
• Intermittent ignition is on while the burner is on
• Solid state flame sensing circuit
• External button to manually reset safety switch after lockout
• Enclosed safety switch must be manually reset after safety shutdown
• R8184M includes 40 VA transformer and Y and G terminals for connection of cooling equipment
• Mounts on standard 4 x 4" junction box
• C554A cadmium sulfide flame detector and 24 VAC thermostat required

honeywell r75-58

honeywell r75-58

• Provides low voltage control of line voltage fan motors and auxiliary circuits in heating, cooling or air conditioning systems
• Transformer powers low voltage control systems and provides overload protection
• Low voltage terminal board provides convenient connections for thermostat and heating and cooling equipment wiring
• Mounts on standard 4 x 4" junction box
• Relay is easily replaced without disturbing wiring
• Includes R8222D general purpose switching relay
• Contact rating - 12 amp full load, 60 amp locked rotor

Honeywell R8285B1053

Honeywell R8285B1053

• 120 VAC 40 VA SPDT,
  ,
  
  
  
  

  HONEYWELL R8285A1048

  
  

  HONEYWELL R8285A1048

• Solid state plug-in amplifiers that respond to flame detector inputs to indicate the presence of flame when used with 7800 series relay modules
• Flame failure response time of 2 or 3 sec
• Flame signal strength ranges from 0 - 5 VDC
• Plug into 7800 relay module through printed circuit board edge connector keyed for proper orientation
• Flame signal test jacks to measure amplifier flame signal voltage
• Color coded labels identify flame detection type
• Dynamic self-check amplifier test the detectors and all electronic components in the flame detection system 7800 series relay module locks out on safety shutdown with flame detection system failure
• Compatible with existing Honeywell flame detectors
• Use with flame sensor gas rectifying flame rods C7004, C7005, C7007, C7008, C7009, Q179; gas, oil, coal ultraviolet flame sensor C7012A, C

R7847A1033

R7847A1033

• Includes NEMA standard type D transformer powers 24 VAC control systems and relay enclosure
• Provides overload protection for transformer
• Convenient connections for thermostat and heating and cooling equipment wiring
• Can be mounted in any indoor location without additional enclosure
• Relay is easily replaced without disturbing wiring

HONEYWELL R8239B1076

HONEYWELL R8239B1076