Air Handler Multi-Position 4 Ton 208/230 VAC TXV R410A 21"

FEATURES:
Smart Diagnostics

Self configuring (ease of installation)

Easier troubleshooting, providing faster service and repair

Energy Tracking capability with the Ion Wall Control. (Energy Tracking has the ability to monitor and estimate the energy consumption of your Ion system.)

Compatibility with wall control depends on software version. Check the installation instructions for minimum requirements. Environmentally Responsible Refrigerant
Technology

R-410A refrigerant chlorine-free, non-ozone depleting

Thermostatic Expansion Valve (TXV) designed to maximize performance with R-410A refrigerant. Bi-flow hard-shutoff with mechanical fittings

International Comfort Products FCMB4B48L0CA

Item#:

FCMB4B48L0CA

Manufacturer Item:

FCMB4B48L0CA

Manufacturer:

INTERNATIONAL COMFORT PRODUCTS

FCMB4B48L0CA_Spec

Air Handler Multi-Position Piston 1-1/2 Ton 208/230 VAC Installed TXV 42-11/16" H x 14-5/16" W x 22-1/6" D

TXV metering device

Aluminum tube and fin evaporator coil

Primary and secondary drain fittings with brass inserts

5 amp automotive type fuse on control board

Multiple electrical entry locations time delay relay (TDR)

HUD approved for manufactured housing

Units tested and certified by manufacturer to achieve a 2% or less leakage rate at 1" WC

1" thick insulation with R value of 4.2

Multi-position installation - upflow or horizontal left standard, horizontal right with minor modification (field convertible to down-flow with accessory kits)

No heat (plug) kit factory installed

5-speed ECM motor

Low VAC age circuit protective fuse (3 amp) inline on wire harness

International Comfort Products FEM4P1800AL

Item#:

FEM4P1800AL

Manufacturer Item:

FEM4P1800AL

Manufacturer:

INTERNATIONAL COMFORT PRODUCTS

FEM4P1800AL_Spec

Air Handler Ceiling Mount 2.5 Ton 208/230 R454B TXV ECM Motor Uncased

MULTIFAMILY CEILING MOUNT FAN COIL

FMU5Z and FMC5Z 1-1/2, 2, 2-1/2, and 3 Tons

Horizontal application only

Accessory field-installed electric heat kits available in 3, 5, 6, 7.5, or 10 kW

40VA, 208/230V-1-60 transformer

All models use Puron Advance, R-454B refrigerant and have a hard-shutoff TXV metering device

Adjustable condensate drain pan FM(C,U)5X, FM(C,U)5Z

Horizontal return applications require field fabricated bottom cover

Cabinets meet the requirement of 1.4% cabinet leakage rate when tested to ASHRAE Standard 193

Cabinets insulated to prevent cabinet sweating

Refrigerant lines and electrical connections can be run out the back or side of casing Performance

PSC motor on all FMU5X & FMC5X models

ECM motor on all FMU5Z & FMC5Z models Easy To Install Service

A-coil design for maximum surface area

Multiple electrical, refrigerant lineset and drain line entry for application flexibility

Primary and secondary drain connections exit from the back or side of the cabinet

Supports furred-down ceiling open return and ducted return applications

Sweat connections for long term reliability

Grooved aluminum tube / aluminum fin coils on FMU5X, FMC5X, FMC5Z, and FMU5Z models with AL in the 10th & 11th position

Item#:

FMU5Z3000AL

Manufacturer Item:

FMU5Z3000AL

Manufacturer:

INTERNATIONAL COMFORT PRODUCTS

FMU5_SPEC

Air Handler Apartment Fan Coil Upflow Only 1.5 Ton 208/230 R545B TXV,PSC,Wallhung

1-1/2, 2, 2-1/2, and 3 Tons

Upflow application only

Accessory field-installed electric heat kits available in 5, 7.5, or 10 kW

208/230-1-60 supply voltage

Cabinet exterior is galvanized sheet metal

Cabinet air leakage rate below 1.4% when tested to ASHRAE Standard 193

Insulated for conditioned space (not to be installed in unconditioned spaces)

All Aluminum coils

Puron Advance refrigerant, TXV standard

International Comfort Products FMA5L1800AL

Item#:

FMA5L1800AL

Manufacturer Item:

FMA5L1800AL

Manufacturer:

INTERNATIONAL COMFORT PRODUCTS

FMA_SPEC

Air Handler Apartment Fan Coil Upflow Only 3 Ton 230/1 R454B PSC Motor TXV

MULTIFAMILY CEILING MOUNT FAN COIL

FMU5Z and FMC5Z 1-1/2, 2, 2-1/2, and 3 Tons

FMU5X and FMC5X 1-1/2, 2, 2-1/2, and 3 Tons All Models

Horizontal application only

Accessory field-installed electric heat kits available in 3, 5, 6, 7.5, or 10 kW

40VA, 208/230V-1-60 transformer

All models use R-454B refrigerant and have a hard-shutoff TXV metering device

Adjustable condensate drain pan FM(C,U)5X, FM(C,U)5Z

Horizontal return applications require field fabricated bottom cover

Cabinets meet the requirement of 1.4% cabinet leakage rate when tested to ASHRAE Standard 193

Cabinets insulated to prevent cabinet sweating

Refrigerant lines and electrical connections can be run out the back or side of casing Performance

PSC motor on all FMU5X & FMC5X models

ECM motor on all FMU5Z & FMC5Z models Easy To Install Service

A-coil design for maximum surface area

Multiple electrical, refrigerant lineset and drain line entry for application flexibility

Primary and secondary drain connections exit from the back or side of the cabinet

Supports furred-down ceiling open return and ducted return applications

Sweat connections for long term reliability

Grooved aluminum tube / aluminum fin coils on FMU5X, FMC5X, FMC5Z, and FMU5Z models with AL in the 10th & 11th position

International Comfort Products FMC5X3000AL

Item#:

FMC5X3000AL

Manufacturer Item:

FMC5X3000AL

Manufacturer:

INTERNATIONAL COMFORT PRODUCTS

FMA_SPEC

Air Handler Heat Pump 20 Ton 230/3 R410A Horizontal Multi-Position and Vertical 56-1/16 H x 89 W x 283/16 L

Multiposition design for horizontal or vertical installation without modification

Two sloped condensate pans on each unit for horizontal or vertical applications

Standard sloped drain pans and cleanable insulation treated with Environmental Protection Agency (EPA) registered antimicrobial agent improves indoor air quality

High-static design meets a wide range of applications than competitive package air handler lines

Economizer accessory provides ventilations air and free cooling

Single refrigerant circuit on 072 and 091 sizes. Dual refrigerant circuit on 120 to 240 sizes. Dual circuit can be field modified for use on single circuit condensers

Single blower on 072 to 120 sizes, dual blower on FHS180 & 240 sizes

Optional 2speed indoor fan with VFD controller 072 to 240 ton sizes

High efficiency copper tube / aluminum coils

Standard factoryinstalled thermostatic expansion valve (TXV) with removable power element

Easy maintenance removal of single panel allows access to virtually all components

Die-formed galvanized steel casings provide durability and structural integrity. Optional paint is available

24volt terminal block for control wiring connection.

Hot water coil, steam coil, and electric heat accessories are available.

International Comfort Products FHS240HAAA2AUA

Item#:

FHS240HAAA2AUA

Manufacturer Item:

FHS240HAAA2AUA

Manufacturer:

INTERNATIONAL COMFORT PRODUCTS

FHS240HAAA2AUA_Spec

Air Handler Apartment Fan Coil Upflow Only 1.5 Ton 208/230 R545B ECM Motor TXV

1-1/2, 2, 2-1/2, and 3 Tons

Upflow application only

Accessory fieldinstalled electric heat kits available in 5, 7.5, or 10 kW

208/230/1/60 supply voltage

Cabinet exterior is galvanized sheet metal

Cabinet air leakage rate below 1.4% when tested to ASHRAE Standard 193

Insulated for conditioned space (not to be installed in unconditioned spaces)

All Aluminum coils

FMA4P

For use with R410A refrigerant utilizing standard piston

FMA4X

R410A refrigerant, TXV standard

PSC motor on all FMA4P

ECM motor on all FMA4X

Motor suspended on rubber grommets for quieter operation

Fresh air intake knockouts in cabinet

Units fits between standard stud spacings

All service access is located in the front

Primary and secondary drain connections exit from the bottom, access panel in bottom of cabinet

No returnair ductwork required in specific applications

Wall hanging brackets included with the unit

International Comfort Products FMA5X1800AL

Item#:

FMA5X1800AL

Manufacturer Item:

FMA5X1800AL

Manufacturer:

INTERNATIONAL COMFORT PRODUCTS

FMA5-Series_Spec

Air Handler Multi-Position 2 Ton ECM R454B TXV 21" Singlar

Refrigerant leak detection dissipation system for added safety

Multi-tap ECM (electronic commutating motor) motors all sizes

Integrated motor controls, with 90-sec off TDR function, have replaced integrated circuit board

Five available speed tags to meet a wide range of applications

Large, grooved tube, louvered fin coils

Efficient, quiet, time-tested blower housings and diffusers

Sturdy, drainable condensate pans

Construction innovations designed to prevent cabinet sweating

Tested for condensate disposal in much tougher conditions than Air Conditioning and Refrigeration Institute requirements

Super-thick R-4.2 insulation with vapor barrier

Pre-painted galvanized steel cabinet

Design meets stringent regulations for cabinet air leakage of less than 2% when tested at 0.5 inches W.C., and less than 1.4% at 0.5 inches W.C. when tested in accordance with ASHRAE 193 standard.

Installation-flexible, multipoise units. 2-piece modular design available for 42 thru 60 sizes. Facilitates attic and crawlspace installations

Horizontal hanging provisions on cabinet

Newly improved filter rack area filter door insulation added for improved air seal. No tools required to access filter

Easy plug-in provisions for heater installation

Factory installed thermostatic expansion valve, TXV, on all coils

Designed for manufactured housing applications

FHMA5X24L0BA

Item#:

FHMA5X24L0BA

Manufacturer Item:

FHMA5X24L0BA

Manufacturer:

INTERNATIONAL COMFORT PRODUCTS

FHMA5X24L0BA_Broc

Air Handler Multi-Position 4 Ton ECM R454B TXV 21" Singlar

Refrigerant leak detection dissipation system for added safety

Multi-tap ECM (electronic commutating motor) motors all sizes

Integrated motor controls, with 90-sec off TDR function, have replaced integrated circuit board

Five available speed tags to meet a wide range of applications

Large, grooved tube, louvered fin coils

Efficient, quiet, time-tested blower housings and diffusers

Sturdy, drainable condensate pans

Construction innovations designed to prevent cabinet sweating

Tested for condensate disposal in much tougher conditions than Air Conditioning and Refrigeration Institute requirements

Super-thick R-4.2 insulation with vapor barrier

Pre-painted galvanized steel cabinet

Design meets stringent regulations for cabinet air leakage of less than 2% when tested at 0.5 inches W.C., and less than 1.4% at 0.5 inches W.C. when tested in accordance with ASHRAE 193 standard.

Installation-flexible, multipoise units. 2-piece modular design available for 42 thru 60 sizes. Facilitates attic and crawlspace installations

Horizontal hanging provisions on cabinet

Newly improved filter rack area filter door insulation added for improved air seal. No tools required to access filter

Easy plug-in provisions for heater installation

Factory installed thermostatic expansion valve, TXV, on all coils

Designed for manufactured housing applications

FHMA5X48L0CA

Item#:

FHMA5X48L0CA

Manufacturer Item:

FHMA5X48L0CA

Manufacturer:

INTERNATIONAL COMFORT PRODUCTS

FHMA5X48L0CA_Broc

Air Handler Commercial Heat Pump 10 Ton 208/230/3 2-Speed Unpainted 56-1/16 H x 49 W x 28-3/16 L

Multi-position design for horizontal or vertical installation without modification.

Standard sloped drain pans and cleanable insulation treated with an immobilized anti-microbial agent to inhibit the growth of bacteria and fungi on the insulation.

High-static design meets a wider range of applications than competitive packaged air handler lines.

Ultra Low Leak Economizer accessory provides ventilation air and free cooling with built in Fault Detection and Diagnostic (FDD) capabilities.

Cooling coils with mechanically bonded fins provide peak heat transfer.

Hot water coil, steam coil, and electric heat accessories are available.

Standard factory-installed thermo-static expansion valves (TXV) with removable power element on FAX/FAS units.

Die-formed galvanized steel casings provide durability and structural integrity. Optional paint is available.

Upgraded unit control board with intuitive indoor fan adjustment.

Standard 2-Speed Indoor Fan Motor system.

International Comfort Products FHX120H2AA0AUA

Item#:

FHX120H2AA0AUA

Manufacturer Item:

FHX120H2AA0AUA

Manufacturer:

INTERNATIONAL COMFORT PRODUCTS

FHX120H2AA0AUA_Spec

Air Handler Multi-Position 3.5 Ton ECM R454B TXV 22" Singlar

Refrigerant leak detection dissipation system for added safety

Multi-tap ECM (electronic commutating motor) motors all sizes

Integrated motor controls, with 90-sec off TDR function, have replaced integrated circuit board

Five available speed tags to meet a wide range of applications

Large, grooved tube, louvered fin coils

Efficient, quiet, time-tested blower housings and diffusers

Sturdy, drainable condensate pans

Construction innovations designed to prevent cabinet sweating

Tested for condensate disposal in much tougher conditions than Air Conditioning and Refrigeration Institute requirements

Super-thick R-4.2 insulation with vapor barrier

Pre-painted galvanized steel cabinet

Design meets stringent regulations for cabinet air leakage of less than 2% when tested at 0.5 inches W.C., and less than 1.4% at 0.5 inches W.C. when tested in accordance with ASHRAE 193 standard.

Installation-flexible, multipoise units. 2-piece modular design available for 42 thru 60 sizes. Facilitates attic and crawlspace installations

Horizontal hanging provisions on cabinet

Newly improved filter rack area filter door insulation added for improved air seal. No tools required to access filter

Easy plug-in provisions for heater installation

Factory installed thermostatic expansion valve, TXV, on all coils

Designed for manufactured housing applications

FHMA5X42L0CA

Item#:

FHMA5X42L0CA

Manufacturer Item:

FHMA5X42L0CA

Manufacturer:

INTERNATIONAL COMFORT PRODUCTS

FHMA5X42L0CA_Broc

Air Handler Commercial Heat Pump 6 Ton 208/230/3 2-Speed Unpainted 56-1/16 H x 49 W x 28-3/16 L