Nu-Calgon 4300-08 RX Systems. Its patented HFC based solvent formulation is powerful enough to flush away sludge, carbon residue, oils, acids, water and other particulate. This makes it ideal for system flushing after burnouts, retrofits and for flushing line sets for R-410A conversions. It is non-toxic, non-flammable and is non-oz.one depleting. From time to time, refrigeration and air conditioning systems suffer failures which result in contamination. The most common such failure is a compressor burnout. During such an event, the refrigeration system becomes contaminated with large quantities of unwanted particulate, sludge, acids, carbon residues and possibly moisture. All of these contaminants must be removed before the system can be returned to duty.

Nu-Calgon 4300-08

Nu-Calgon 4186-08 Green Clean Concentrated All-Purpose Coil Cleaner, 1 Gallon

Nu-Calgon 4186-08

Nu-Calgon 4301-05 Rx-Acid Scavenger, 3.8 oz. Pressurized Can, Gas, Mild Rx-Acid Scavenger provides a better, more convenient way to neutralized or "scavenge" acid in refrigeration, air conditioning systems after burnouts or during normal on-going systems maintenance. Normal dosage rate is 2 fl. oz. of Rx-Acid Scavenger for up to one Gallon of system oil. That is 50% less than other acid neutralizing products. This "low treat" feature means far less material has to be added to the systems. Rx-Acid Scavenger is formulated for use with all lubricants - mineral, alkylbenzene and polyol ester. Use after system burnout to scavenge acid products in the system, or change a system with Rx-Acid Scavenger to neutralize acid conditions should they develop.

Nu-Calgon 4301-05

Nu-Calgon 4301-06 Rx-Acid Scavenger Connect Inject,
Nu-Calgon 4301-06

Nu-Calgon 4301-06

Nu-Calgon 4300-30 RX11-flush liquid is a new and improved chemistry that is the next generation in flushing technology. It remains a constant boiling solvent and is now stronger, faster acting and dissolves more oil, moisture and contaminants than any other flush. It is ideal for line sets, burnouts and other flushing requirements. It is non-toxic, non-flammable and is non-oz.one depleting.

Non-toxic and non-flammable
• Optimal boiling point enhances complete evaporation
• Can be used for new system cleaning, retrofits, and flushing line sets or after burnouts
• Cleaning is fast and efficient leaving no residue
• Formulated for R-410A retrofits
  
  

  Nu-Calgon 4300-30

Nu-Calgon 4299-T8 Pump Protector, 10 oz. Spray Can, Colorless Foam-in shut down corrosion protection for all types of pumps any pump that is shut down and drained part of the time should be safeguarded with aerosol pump protector. Pumps used in cooling towers, swimming pools and vacation homes, auxiliary pumps, marine and industrial pumps can develop corrosion deposits on the impeller and other close-tolerance areas during shut down, causing the pump to bind. Aerosol pump protector prevents this corrosion and lubricates the pump so that it starts right up every time! pump protector is water soluble and will not cause any foaming problem when the pump is started. If the pump is used for drinking water, flush it thoroughly by running water off a few minutes before placing the pump back in service. Protects seasonally operated pumps against corrosion during shutdowns by "winterizing" them. When corrosion occurs in close-tolerance areas, it can cause the impeller to stick or bind. Protect your clients investment and your reputation! Safe for all types of water pumps and it requires no special rinsing at start-up.

• Protects against corrosion and ends-pump impeller binding
• Convenient aerosol package
• Safe for all types of water pumps
• One can is enough for most pumps
• Requires no special rinsing at startup
• Protects pool pumps throughout the winter
• This product has been authorized by the USDA for use in federally inspected meat and poultry plants
• 95% volatile
• Level 1 heat of combustion
• 13 cm flame height, 4 - 5 sec flammability duration Foam-in shut down corrosion protection for all types of pumps any pump that is shut down and drained part of the time should be safeguarded with aerosol pump protector. Pumps used in cooling towers, swimming pools and vacation homes, auxiliary pumps, marine and industrial pumps can develop corrosion deposits on the impeller and other close-tolerance areas during shut down, causing the pump to bind. Aerosol pump protector prevents this corrosion and lubricates the pump so that it starts right up every time! pump protector is water soluble and will not cause any foaming problem when the pump is started. If the pump is used for drinking water, flush it thoroughly by running water off a few minutes before placing the pump back in service. Protects seasonally operated pumps against corrosion during shutdowns by "winterizing" them. When corrosion occurs in close-tolerance areas, it can cause the impeller to stick or bind. Protect your clients investment and your reputation! Safe for all types of water pumps and it requires no special rinsing at start-up.
  
  

  Nu-Calgon 4299-T8

Nu-Calgon 4151-08 Over time, the inside of mini-split units become plugged with dirt and grime, as well as coated with mold and mildew. The coil, blower wheel, condensate pan and plastic housing need to be cleaned and disinfected regularly. In addition, drain pan treatment is recommended to guard against overflows due to plugged drain lines. The Complete Care mini-split kit is the solution to all of these problems and is designed to do the job quickly and effectively.

Cleans, disinfects, and deodorizes
• Controls mold and mildew formation
• Disinfectant against staphylococcus aureus, salmonella enterica and pseudomonas aeruginosa
• Protects condensate pans and lines from plugging
• Treats 2-3 mini-splits
• Contains one 18 oz. can of Evap-fresh no rinse evaporator coil cleaner and disinfectant and one purcool green mini strip
  
  

  4151-08

Nu-Calgon 4175-10 Ecopure R290 Charging Assembly Meets AHRI 700 Standard

Nu-Calgon 4175-10

Nu-Calgon 4128-03 This advanced technology product is made with Cerflon for high performance in a non-drying oily film penetrating lubricant. The"4 in 1" action makes it highly versatile with the ability to penetrate, lubricate, displace moisture, and provide superior resistance to corrosion. Its ultra low surface tension penetrates deep to free frozen parts and assemblies. It contains NO chlorinated solvents or ozone depleters, and a 360 deg spray valve allows for easy use in any position. The non-aggressive formula is safe for use on most plastics and painted surfaces, making it an excellent choice for virtually any general-purpose lubrication need. The addition of Cerflon not only improves lubricity but elevates temperature range to in excess of 500 deg F.

Nu-Calgon 4128-03

Nu-Calgon 4186-24 Green Clean Concentrated All-Purpose Coil Cleaner, 1 qt Green Clean is a pleasantly scented, concentrated environmentally friendly, all-purpose cleaner designed for the rapid removal of grime and other heavy soils. It instantly penetrates greasy and oily surfaces, providing powerful emulsifying ingredients that chemically soften and dissolve the deposits, making them easy to remove. A safer, effective, alternative to toxic cleaners, bleaches and solvents! Green Clean is non-corrosive, economical and is qualified by the U.S. EPA Safer Choice Program. The Green Clean quart comes with a versatile foam tip applicator, which provides the choice of either a spray or foam application.

Nu-Calgon 4186-24

Nu-Calgon 4300-38 RX11-flush Liquid Starter Kit, Liquid, Clear, Slight Rx11-flush Liquid is a new and improved chemistry that is the next generation in flushing technology. It remains a constant boiling solvent and is now stronger, faster acting and dissolves more oil, moisture and contaminants than any other flush. It is ideal for line sets, burnouts and other flushing requirements. It is sold in a 19.5 fl oz. unpressurized can as well as in a Starter Kit, which consists of Rx11-flush Liquid, Rx11-flush Liquid Tank, Rx11-flush 24" Hose, and Rx11-flush Gun.,

Nu-Calgon 4300-38

Nu-Calgon 4301-02 RX-Acid scavenger provides a better, more convenient way to neutralized or scavenge acid in refrigeration, air conditioning systems after burnouts or during normal on-going systems maintenance. Normal dosage rate is 2 fl oz. of Rx-acid scavenger for up to 1 Gallon of system oil. That is 50% less than other acid neutralizing products. This low treat feature means far less material has to be added to the systems. Rx-acid scavenger is formulated for use with all lubricants - mineral, alkylbenzene and polyolester. Use after system burnout to scavenge acid products in the system or change a system with Rx-acid scavenger to neutralize acid conditions should they develop.

Nu-Calgon 4301-02