Noisy pipes, valves, and other air-related noises are often accepted as the signs of a functioning system. Excessive pump noise, cavitation, and cascading in terminal units are considered normal. But air in system water can cause corrosion, reduced efficiency, poorly heated or inadequately cooled rooms, accelerated component wear and on-going complaints. There is a device that will keep your system free of air permanently. Less maintenance, quiet operation, fewer costs!. Unlike conventional air eliminators or air scoops, the Spirovent completely eliminates 100% of the free air, 100% of the entrained air, and up to 99.6% of the dissolved air in the system. Consisting of woven copper wire soldered to a copper tube, the patented Spirotube creates a low velocity area in the Spirovent that scrubs the bubbles from the water. The air bubbles rise and collect in the air chamber before they are vented from the system via an integral automatic valve. Air problems become a thing of the past.

• Maintenance free
• No venting required
• Vent head is designed to stay dry, dirt and leak resistant
• 1/2" male thread port for pressure testing or remote venting of unwanted gases
• Quiet operation
• Increased component life
• Reduced oxygen based corrosion and pump cavitation
• The automatic air vent is guaranteed not to leak and can only be closed by the installer for a pressure test
• The air chamber has been designed so that dirt cannot reach the valve
• Large capacity collection chamber reduces the need for frequent draining
• Drain valve for flushing out the dirt
• Brass vent head
• Non-ferrous float
• ViTon seal and o-ring
• Copper coalescing medium

Sid Harvey Item #:B156-23: Replaces Part #:'s : L38-345,
,

Spirotherm B156-23

Hydrolevel Safgard 550 Low Water Cut-Off, 120 VAC, 250 psi, Manual Reset

• Provides step-by-step, diagrammed instructions for fast, easy installation and wiring
• Burner circuit locks-out if water remains below probe for 30 sec
• Burner circuit test butTon allows for testing the control without lowering the water level and indicator lights for easy troubleshooting
• SPDT switch contact

,
,

Hydrolevel B112-3

Noisy pipes, valves, and other air-related noises are often accepted as the signs of a functioning system. Excessive pump noise, cavitation, and cascading in terminal units are considered normal. But air in system water can cause corrosion, reduced efficiency, poorly heated or inadequately cooled rooms, accelerated component wear and on-going complaints. There is a device that will keep your system free of air permanently. Less maintenance, quiet operation, fewer costs!. Unlike conventional air eliminators or air scoops, the Spirovent completely eliminates 100% of the free air, 100% of the entrained air, and up to 99.6% of the dissolved air in the system. Consisting of woven copper wire soldered to a copper tube, the patented Spirotube creates a low velocity area in the Spirovent that scrubs the bubbles from the water. The air bubbles rise and collect in the air chamber before they are vented from the system via an integral automatic valve. Air problems become a thing of the past.

• Maintenance free
• No venting required
• Vent head is designed to stay dry, dirt and leak resistant
• 1/2" male thread port for pressure testing or remote venting of unwanted gases
• Quiet operation
• Increased component life
• Reduced oxygen based corrosion and pump cavitation
• The automatic air vent is guaranteed not to leak and can only be closed by the installer for a pressure test
• The air chamber has been designed so that dirt cannot reach the valve
• Large capacity collection chamber reduces the need for frequent draining
• Drain valve for flushing out the dirt
• Brass vent head
• Non-ferrous float
• ViTon seal and o-ring
• Copper coalescing medium

Sid Harvey Item #:B156-21: Replaces Part #:'s : L38-434,
,

Spirotherm B156-21

67 Mechanical Low Water Cut-Off 120/240 VAC 20 psi Automatic Reset

• Quick hook-up fittings provided
• Lever operated, full port ball valve for easy blow down
• Adjustable Bx outlet for easy installation
• Dual precision switches for dependable operation of cut-off, alarm or electric water feeder

Sid Harvey Item #:B103: Replaces Part #:'s : 13609,
,

McDonnell & Miller B103

xylem Float Low Water Cut-Off 120 - 240 VAC 20 psi Automatic

• 125 VA pilot duty rating
• 4-1/8" length insertion
• Packless bellows
• Dual precision switches for dependable operation of the low water cut-off and an alarm or electric water feeder
• For mounting in 2-1/2" NPT boiler side tappings
• Adjustable Bx outlet for easy installation

,
,

McDonnell & Miller B106

Mcdonnell & Miller 369 Low Water Cut-Off, 120/240 VAC, 20 psi, Automatic Reset

• Adjustable Bx outlet for easy installation
• Dual precision switches for dependable operation of cut-off, alarm or electric water feeder
• Packless bellows
• Millivolt circuits

Sid Harvey Item #:B106-4: Replaces Part #:'s : L38-768,
,

McDonnell & Miller B106-4

Taco flo-cheks have dependably stopped gravity circulation in forced hot water heating systems for over 40 years. Flo-cheks open automatically when the circulator starts running. They feature a thumb screw to manually open the valve and are available in a cast iron universal body and a bronze sweat in-line configuration.

• Flo-cheks allow heat to flow only into the zones that are calling for heat
• Thumb screw can be manually opened for gravity feed applications if the main circulator stops operating
• Taco flo-cheks open automatically when the circulator starts running

Sid Harvey Item #:B146-19: Replaces Part #:'s : 21426,

,

Taco B146-19

Taco flo-cheks have dependably stopped gravity circulation in forced hot water heating systems for over 40 years. Flo-cheks open automatically when the circulator starts running. They feature a thumb screw to manually open the valve and are available in a cast iron universal body and a bronze sweat in-line configuration.

• Flo-cheks allow heat to flow only into the zones that are calling for heat
• Thumb screw can be manually opened for gravity feed applications if the main circulator stops operating
• Taco flo-cheks open automatically when the circulator starts running

Sid Harvey Item #:B146-20: Replaces Part #:'s : HYD160-B146-20 | 4030 |,
,

Taco B146-20

Taco Flo-Checks prevent gravity circulation in forced hot water heating systems during periods when the boiler is hot, but the space heating zone is not wanted. This makes it possible to use the heating boiler to maintain domestic hot water year-round. You can also use Flo-Checks in systems with multiple circulator zones to allow heat to flow only into the zones that are calling for heat. In addition, the thumb screw can be opened manually for gravity feed applications, if the main circulator stops operating.

• In systems with multiple circulator zones to allow heat to flow only into the zones that are calling for heat
• Feature a thumb screw to manually open the valve and are available in a cast iron universal body and a bronze sweat in-line configuration
• The thumb screw can be opened manually for gravity feed applications, if the main circulator stops operating
• Open automatically when the circulator starts running, when the room thermostat is satisfied and the circulator is stopped, the flo-checks close immediately, preventing gravity circulation
• Water or glycol media

Sid Harvey Item #:B146-21: Replaces Part #:'s : 4031,
,

Taco B146-21

Taco Flo-Checks prevent gravity circulation in forced hot water heating systems during periods when the boiler is hot, but the space heating zone is not wanted. This makes it possible to use the heating boiler to maintain domestic hot water year-round. You can also use Flo-Checks in systems with multiple circulator zones to allow heat to flow only into the zones that are calling for heat. In addition, the thumb screw can be opened manually for gravity feed applications, if the main circulator stops operating.

• In systems with multiple circulator zones to allow heat to flow only into the zones that are calling for heat
• Feature a thumb screw to manually open the valve and are available in a cast iron universal body and a bronze sweat in-line configuration
• The thumb screw can be opened manually for gravity feed applications, if the main circulator stops operating
• Open automatically when the circulator starts running, when the room thermostat is satisfied and the circulator is stopped, the flo-checks close immediately, preventing gravity circulation
• Water or glycol media

Sid Harvey Item #:B146-22: Replaces Part #:'s : 21428,
,

Taco B146-22

Hydrolevel Safgard 450 Low Water Cut-Off, 120 VAC, 15 psi, Automatic Reset

• Burner circuit contacts open after 15 sec delay in a low water condition
• Delay prevents short cycling caused by momentary fluctuations in the boiler water level
• Automatically reactivates burner circuit 30 sec after water reaches the probe, allowing optional water feeder to raise water level above the probe
• SPDT switch contact

,
,

Hydrolevel B103-38

Hydrolevel Safgard 170SV Low Water Cut-Off, 120 VAC, 160 psi, Automatic Reset

• Combustion pressure switch check feature and communication interface capability
• Heavy duty electro-mechanical design for long life
• Automatically re-energizes circuit upon return to safe water level
• Equipped with shorter probe for mounting in standard reducing tees
• SPDT switch contact
• Includes shorter EL1214-SV probe suitable for mounting in standard black tee

Sid Harvey Item #:B103-30: Replaces Part #:'s : 3W400,
,

Hydrolevel B103-30