Parker commercial pressure regulator (S)PORT/(S)PORTII valves are designed with stainless steel bonnet bolts, adjusting stems, and pisTon and plug assemblies. The result is a regulator designed to withstand the rigorous application environment a low side regulator must endure. Models are available in combinations of connection sizes, port sizes and features as designated by the model code. Unlike some competitive models of low side regulators that utilize high pressure discharge gas as a pilot source, they are piloted with upstream pressure. This eliminates the requirement for hot gas headers, isolation devices, piping, and the labor associated with the installation of other valves. Flare connections from high pressure pilot lines are also eliminated, minimizing sources for prospective leaks. The valves are an integrated assembly of (4) modules: 1) a body, which contains no moving parts, 2) a capacity cartridge, which contains both pisTon and modulating plug, and defines the port size and onto which the pilot solenoids providing the"S" (shut-off) or"B" (bypass) features are added as required, 4) the bonnet, containing the range spring and adjustment screw, which is set for the value of pressure which the valve is to maintain. The unique modular design allows the regulator to be soldered into the line without disassembly, yet provides full access for disassembly, cleaning and servicing from the top only. Interchangeable capacity cartridges facilitate flow revisions should an undersized or oversized condition be encountered, while pilot adapters can be changed out to add features or even change functions.

• Retrofitting for additional evaporator capacity is simple and requires no pipe line revisions
• The pisTon and plug assembly can handle reduced flow conditions and controlling down to about 15% of the valve's maximum capacity
• 1-1/8" OD
• Designed entirely with corrosion resistant materials
• New cooler running coil and open frame coil housing
• New dual VAC age 208/240/60 Hz coil
• Conveniently located access fitting
• Pilot operated for close control at desired set-point
• Excellent regulation at light loads
• Interchangeable capacity cartridges
• Low pressure drop
• Few moving parts
• Long-life stainless steel diaphragms (no bellows to fail)
• Pilot electric shut-off
• All service from the top
• Sweat-in-place without disassembly

,
,

Parker SPORT-07-07

Heatcraft Parts 23308101 Coil Face Heater Clip 1/2" OD

23308101

Berry Global 367-17-2 Nashua Foil Mastic Butyl Rubber Sealant Tape 2" x 100' (Silver)

Mueller Copper W13-23

Berry Global 367-17-3 Nashua Foil Mastic Butyl Rubber Sealant Tape 3" x 100' (Silver)

Berry Global 367-17-3

Argo Industries Parts A10-ARGO Clamp On Aquastat

argo industries a10-argo

Mars Universal Remote will operate with virtually any mini-split produced in any region of the world. Programming is accomplished by imputing your mini-split brand code or use the easy and intuitive self learn mode to set-up the remote to operate your mini-split. Operates with 2 AAA batteries..

Motors & Armatures 0448A

Scale, lime and rust build-up decreases the efficiency of any water based equipment, increases energy usage, and decreases equipment life. Flow-Aide Biodegradable Descaler quickly and safely dissolves water scale, lime, rust, and other water formed deposits, restoring efficiency to most all water based equipment. Flow-Aide Biodegradable Descaler is a non-toxic concentrate which is certified to NSF/ANSI 60 for use as a cleaner in potable water systems.

• Non-corrosive
• Non-toxic
• Fully biodegradable
• Safe to handle
• Zero VOC

Honeywell 107408

Therma-Flow Parts STW-PLATE+GASKET

Therma Flow Parts PLATE-ECT

Outstanding Performance:
This damper was specifically designed with R8 insulation specification in mind to contribute to energy savings and help the system pass efficiency audits. Best of all, it helps eliminate hot and cold spots, the biggest cause of callbacks. The improved internal design creates a slower return that ensures a quiet operation.
Installation Made Easy
For fast, accurate installation with no callbacks, the TrueZONE Damper has you covered with a range of features that simplify installation in most applications:

Adjustable Range Stops  Easy to understand and set by utilizing a pushin lever. Theyre used to bleed air into the zones which helps lower pressure and reduce noise.

Push-In Terminals  The same easy wiring design used on TrueZONE Panels. No tools needed, has space for two wires.

Taping Flange  Lets you position insulation under it before sealing with foil tape.

Mechanical Position Indicator  Easy viewing through a clear window.

LED Indicator Lights  Red indicates the damper is closed and green indicates open (used in 3-wire applications)

Honeywell ZD8X10TZ

Trane Parts CNT1015 Limit Switch 135 Degrees,

CNT1015

Empire Comforts DV772 Electrode for use with DV-225-3SG, 4SG- DV-235-3SG, 4SG- DV-25-1SG, 2SG- DV-35-1SG Fireplace

DV772

First Company A/C Parts E141 Air Handler Cycle Timer

First Company A/C Parts E141