Honeywell PV150 The Resideo SuperVent, purges air through a no clog vent assembly, to control dirt and debris and minimize air vent fouling in Hydronic heating systems, while eliminating the need for bleeding.

No clog vent
• Dirt and debris resistant
• 360 deg adjustable collar ring for installation flexibility
• Stainless steel concentrator which eliminates gurgling noise
• Bronze body for rigid construction
  
  

  PV150

Noisy pipes, valves, and other air-related noises are often accepted as the signs of a functioning system. Excessive pump noise, cavitation, and cascading in terminal units are considered normal. But air in system water can cause corrosion, reduced efficiency, poorly heated or inadequately cooled rooms, accelerated component wear and on-going complaints. There is a device that will keep your system free of air permanently. Less maintenance, quiet operation, fewer costs!. Unlike conventional air eliminators or air scoops, the Spirovent completely eliminates 100% of the free air, 100% of the entrained air, and up to 99.6% of the dissolved air in the system. Consisting of woven copper wire soldered to a copper tube, the patented Spirotube creates a low velocity area in the Spirovent that scrubs the bubbles from the water. The air bubbles rise and collect in the air chamber before they are vented from the system via an integral automatic valve. Air problems become a thing of the past.

Maintenance free
• No venting required
• Vent head is designed to stay dry, dirt and leak resistant
• 1/2" male thread port for pressure testing or remote venting of unwanted gases
• Quiet operation
• Increased component life
• Reduced oxygen based corrosion and pump cavitation
• The automatic air vent is guaranteed not to leak and can only be closed by the installer for a pressure test
• The air chamber has been designed so that dirt cannot reach the valve
• Large capacity collection chamber reduces the need for frequent draining
• Drain valve for flushing out the dirt
• Brass vent head
• Non-ferrous float
• Viton seal and O-Ring
• Copper coverall Lengthescing medium
  
  

  VJV125FT

Resideo Braukmann AMU200-RP Union Gasket AM Series

Resideo Braukmann AMU200-RP

Watts AS-MB-100 Microbubble Air Separator, 1", IPS, 150 psig, 240 deg F, 15 GPM, Forged Brass, 3-12/16" L x 6-15/16" H

Features a durable brass body construction, corrosion-resistant polyphenylsulfone coverall Lengthescing media that withstands petroleum based cleaners, glycol anti-freeze
• Requires no minimum inlet/outlet piping length for proper operation
• DuoVent air vent assembly has a high-capacity and high-temperature rating
• Fully serviceable - can be disassembled for inspection and cleaning
• Bottom tapping for use with series RBFF residential boiler fill fitting
  
  

  Watts Water AS-MB100

Watts Water BD911S Bronze Combination Fill Valve Feeder and Backflow Preventer, 1/2" NPT

Pre-assembled for ease of installation
• Push button fast fill with auto-stop to prevent system over-pressurization
• Dial indicator eliminates need for pressure gauge
• High capacity fill valve for quick system filling and purging
• All bronze body construction union solder x NPT connections
• Dial indicator plus or minus 2 psi
• Series BD911 combination fill valve and backflow preventer consists of a model 9D backflow preventer and model BD1156F feed water pressure regulator in one pre-assembled unit
• Combination bronze dial set fill valve
  
  

  BD911S

Taco boiler feed valves automatically feed water to a system whenever pressure in the system drops below the pressure setting of the valve. The dual control models combine the boiler feed with an in-line pressure relief valve. The built-in check prevents emptying the system if incoming pressure falls. They feature fast fill rates and an exclusive, lockable fast fill lever. Each valve is adjustable from10 to 25 psi, has a built-in check to prevent the emptying of the system if incoming pressure fails, and the easy to use fast fill lever is lockable.

Fast fill rate
• Exclusive fast fill lever lock
• Built-in check to prevent emptying the system if incoming pressure fails
• Pressure setting adjustment separated from fast fill lever for easy, fast adjustment
• 100 psi maximum supply side pressure, 30 psi relief valve setting, 12 psi factory setting
  
  

  Taco B143-12

Taco boiler feed valves automatically feed water to a system whenever pressure in the system drops below the pressure setting of the valve. The dual control models combine the boiler feed with an in-line pressure relief valve. The built-in check prevents emptying the system if incoming pressure falls. They feature fast fill rates and an exclusive, lockable fast fill lever. Taco boiler feed valves have set the standards for dependable service. Each valve is adjustable from 10 - 25 psi, has a built-in check to prevent the emptying of the system if incoming pressure fails, and the easy to use fast fill lever is lockable.

Fast fill rate on all models
• Exclusive fast fill lever lock
• Built-in check to prevent emptying the system if incoming pressure fails
• Pressure setting adjustment separated from fast fill lever for easy, fast adjustment
• 100 psi maximum supply side pressure, 12 psi factory setting of system side
  
  

  Taco B143-13

Bell & Gossett B138 F3 Brass Dual Unit Valve 1/2" NPT 30 PSI Relief 12 PSI Reducing
Reducing valves fill the system to a preset pressure for optimum performance. Combination dual unit valves include pressure reducing valve and relief valve. Both Valves are equipped with an EPDM diaphragm. The diaphragm operated relief valve operates with a low differential between opening and closing pressures. The diaphragm operated pressure reducing valve is equipped with an inlet strainer and built-in low inlet pressure check valve.

Low inlet pressure check valve help prevent loss of system pressure if the supply water drops below system pressure
• Convenient cleanable strainer is designed to prevent dirt and sediment from entering the system
• Relief and FB-38 pressure reducing component valves
  
  

  Bell & Gossett B138

Bell & Gossett B-38 Cast Brass Pressure Reducing Valve, 1/2", NPT, 10 - 25 psig

Fast fill feature reduces start-up time and labor
• Low inlet pressure check valve help prevent loss of system pressure if the supply water drops below system pressure
• Convenient cleanable strainer is designed to prevent dirt and sediment from entering the system
• Brass body construction is highly resistant to corrosion-ideal for water systems
• Reducing valves protect heating and plumbing systems against excessive line pressures
• Equipped with built-in-strainer and low inlet pressure check valve
• They are factory set at specified limits although adjustment is easily made
• Construction - cast brass body, with special insert diaphragm, EPDM check valve, brass seat, brass with EPDM insert stem, brass valve plate, stainer and strainer nut wetted parts and steel non-wetted parts
  
  

  B138-8A

Noisy pipes, valves, and other air-related noises are often accepted as the signs of a functioning system. Excessive pump noise, cavitation, and cascading in terminal units are considered normal. But air in system water can cause corrosion, reduced efficiency, poorly heated or inadequately cooled rooms, accelerated component wear and on-going complaints. There is a device that will keep your system free of air permanently. Less maintenance, quiet operation, fewer costs!. Unlike conventional air eliminators or air scoops, the Spirovent completely eliminates 100% of the free air, 100% of the entrained air, and up to 99.6% of the dissolved air in the system. Consisting of woven copper wire soldered to a copper tube, the patented Spirotube creates a low velocity area in the Spirovent that scrubs the bubbles from the water. The air bubbles rise and collect in the air chamber before they are vented from the system via an integral automatic valve. Air problems become a thing of the past.

Maintenance free
• No venting required
• Vent head is designed to stay dry, dirt and leak resistant
• 1/2" male thread port for pressure testing or remote venting of unwanted gases
• Quiet operation
• Increased component life
• Reduced oxygen based corrosion and pump cavitation
• The automatic air vent is guaranteed not to leak and can only be closed by the installer for a pressure test
• The air chamber has been designed so that dirt cannot reach the valve
• Large capacity collection chamber reduces the need for frequent draining
• Drain valve for flushing out the dirt
• Brass vent head
• Non-ferrous float
• Viton seal and O-Ring
• Copper coverall Lengthescing medium
  
  

  Spirotherm B156-24

Noisy pipes, valves, and other air-related noises are often accepted as the signs of a functioning system. Excessive pump noise, cavitation, and cascading in terminal units are considered normal. But air in system water can cause corrosion, reduced efficiency, poorly heated or inadequately cooled rooms, accelerated component wear and on-going complaints. There is a device that will keep your system free of air permanently. Less maintenance, quiet operation, fewer costs!. Unlike conventional air eliminators or air scoops, the Spirovent completely eliminates 100% of the free air, 100% of the entrained air, and up to 99.6% of the dissolved air in the system. Consisting of woven copper wire soldered to a copper tube, the patented Spirotube creates a low velocity area in the Spirovent that scrubs the bubbles from the water. The air bubbles rise and collect in the air chamber before they are vented from the system via an integral automatic valve. Air problems become a thing of the past.

Maintenance free
• No venting required
• Vent head is designed to stay dry, dirt and leak resistant
• 1/2" male thread port for pressure testing or remote venting of unwanted gases
• Quiet operation
• Increased component life
• Reduced oxygen based corrosion and pump cavitation
• The automatic air vent is guaranteed not to leak and can only be closed by the installer for a pressure test
• The air chamber has been designed so that dirt cannot reach the valve
• Large capacity collection chamber reduces the need for frequent draining
• Drain valve for flushing out the dirt
• Brass vent head
• Non-ferrous float
• Viton seal and O-Ring
• Copper coverall Lengthescing medium
  
  

  Spirotherm B156-22

Noisy pipes, valves, and other air-related noises are often accepted as the signs of a functioning system. Excessive pump noise, cavitation, and cascading in terminal units are considered normal. But air in system water can cause corrosion, reduced efficiency, poorly heated or inadequately cooled rooms, accelerated component wear and on-going complaints. There is a device that will keep your system free of air permanently. Less maintenance, quiet operation, fewer costs!. Unlike conventional air eliminators or air scoops, the Spirovent completely eliminates 100% of the free air, 100% of the entrained air, and up to 99.6% of the dissolved air in the system. Consisting of woven copper wire soldered to a copper tube, the patented Spirotube creates a low velocity area in the Spirovent that scrubs the bubbles from the water. The air bubbles rise and collect in the air chamber before they are vented from the system via an integral automatic valve. Air problems become a thing of the past.

Maintenance free
• No venting required
• Vent head is designed to stay dry, dirt and leak resistant
• 1/2" male thread port for pressure testing or remote venting of unwanted gases
• Quiet operation
• Increased component life
• Reduced oxygen based corrosion and pump cavitation
• The automatic air vent is guaranteed not to leak and can only be closed by the installer for a pressure test
• The air chamber has been designed so that dirt cannot reach the valve
• Large capacity collection chamber reduces the need for frequent draining
• Drain valve for flushing out the dirt
• Brass vent head
• Non-ferrous float
• Viton seal and O-Ring
• Copper coverall Lengthescing medium
  
  

  Spirotherm B156-23