Honeywell R7847A1033/U Green Rectifying Flame Amplifier for Primary Safety Control7800 Series Relay

Solid state plug-in amplifiers that respond to flame detector inputs to indicate the presence of flame when used with 7800 series relay modules
• Flame failure response time of 2 or 3 sec
• Flame signal strength ranges from 0 - 5 VDC
• Plug into 7800 relay module through printed circuit board edge connector keyed for proper orientation
• Flame signal test jacks to measure amplifier flame signal voltage
• Color coded labels identify flame detection type
• Dynamic self-check amplifier test the detectors and all electronic components in the flame detection system 7800 series relay module locks out on safety shutdown with flame detection system failure
• Compatible with existing Honeywell flame detectors
• Use with flame sensor gas rectifying flame rods C7004, C7005, C7007, C7008, C7009, Q179; gas, oil, coverall Length ultraviolet flame sensor C7012A
  
  

  honeywell r7847a1033

Sigma Engineering Parts SE-995-02 Liquid Level Gasket Neoprene

Sigma Engineering SE-995-02

Inner-Tite Corporation R81300 Brass Fusible Angle Valve, 3/8 x 1/4", Inner-Tite manufactures a complete line of fusible oil valves, fusible angle valves, check valves, tanks valves and a variety of accessories engineered for use at oil burner installations. These high performance valves feature strong steel bodies and positive release valves. All Inner-Tite valves are manufactured to precise standards using only the finest raw materials guaranteeing consistent performance for years to come.

Inner-Tite Corporation R81300

Mcdonnell & Miller 344100 Upper Tube Assembly for 67 Series Low Water Cut-offs

mcdonnell & miller sa66-35

Bramec Corporation and is a major distributor in the Electrical, Plumbing, Hardware and HVAC/R industry

SLURK24V Hot Surface Ignitor Tip 2-1/2" Buss Bar

bramec slurk24v

Sealed Unit Parts SIG1100 Silicon Carbide Round Hot Surface Furnace Igniter, 120 VAC, 4 amp at 132 VAC Maximum

Universal igniter kit is designed to replace hundreds of OEM part numbers
• Universal replacement minimizes inventory
• Superior gas lighting ability
• Lower power consumption
• 18 ga copper high temperature fiberglass insulated lead wires
• Offer an efficient, stronger, reliable design
• Faster time to temperature response
• Stronger more durable design
• More robust in transit
• Higher resistance to oxidation
• Longer usable life
• Greater physical strength
• Easy installation
• Time to temperature (1800 deg F) less than 17 sec at 120 VAC
• 40 - 100 ohm at 75 plus or minus 10 deg F cold resistance
• Includes (3) mounting brackets, (1) self tapping screw, (2) porcelain wire nuts
  
  

  sealed unit parts sig1100

Thermo-Disc STC6257 Thermal Cutout Fuse Link, 257 deg F, 12 VAC, 15 amp

Provides reliable back-up protection for temperature controlling thermostats
• Applied to millions of appliances and personal care products
• Rated for continuous operating currents up to 1 amp at 25 VAC, 5 amp at 24 VDC
  
  

  sealed unit parts stc6257

Thermo-Disc STC6333 Thermal Cutout Fuse Link, 333 deg F, 12 VAC, 15 amp

Provides reliable back-up protection for temperature controlling thermostats
• Applied to millions of appliances and personal care products
• Rated for continuous operating currents up to 1 amp at 25 VAC, 5 amp at 24 VDC
  
  

  sealed unit parts stc6333

Thermo-Disc STC5377 Thermal Cutout Fuse Link, 377 deg F, 12 VAC, 15 amp

Provides reliable back-up protection for temperature controlling thermostats
• Applied to millions of appliances and personal care products
• Rated for continuous operating currents up to 1 amp at 25 VAC, 5 amp at 24 VDC
  
  

  STC5377

Installation of a spillage safety switch is recommended for LP and natural gas fired systems with draft hoods. This device is installed to detect flue gas spillage caused by a blocked flue system and/or inadequate draft. This device must be installed by a qualified installer in accordance with the manufacturer's installation instructions. Wiring must be in accordance with the National Electrical Code and applicable local codes.

Efficiently detect flue gas spillage due to a blocked flue, continuous down drafting or inadequate draft condition
• With the safety switch wired in series with the burner circuit, the switch will de-energize the systems burner or burner control once it senses the spillage of hot flue gases
• Gold contact
• Includes (1) 6 feet length of 12/2 jacketed lead wire, (1) 8 feet length of 12 ga jumper wire, (3) adhesive tabs and switch jumper wire and (2) #8 self-drilling sheet metal screws
  
  

  field controls ssk-3

Honeywell S9200U1000 Universal Hot Surface Ignition Control Module

honeywell s9200u1000

Honeywell S8910U3000 Hot Surface Ignition Control Module

honeywell s8910u3000