Fujitsu FH3617TTSJSN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections

Fujitsu FH3617TTSJSN

Fujitsu FH3017TPSJSN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections

• 42K BTU 3-1/2 Ton
• 208/230/1 VA
• 21" Wide
• PSC Motor
• Multi-Position,
  

  Fujitsu FH4221TPSJSN

Fujitsu FH4821TPSASN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections

• 48K BTU 4 Ton
• 208/230/1 VAC
• 21" Wide
• Multi-Position,
  ,
  

  Fujitsu FH4821TTSJSN

STANDARD SPECIFICATIONS

Rifled copper tubing, enhanced aluminum fins.

Immersion-tested at 500 psi, then nitrogen-pressurized and sealed.

Left- or right-hand refrigerant and plumbing connections.

Liquid line - 3/8 ODS, suction line - 3/4 ODS on 1-1/2- 3 ton & 7/8 ODS on 3-1/2 - 5 ton.

Externally mounted flowrater body with Schrader valve for hiss-testing.

Heavy duty plastic drain pans on most models.

Upflow without field modification. Downflow applications require plate kit, included.

AHRI certifiable with all brands of A/C and heat pump systems.

ETL listed for use with both R-22 and R-410a when proper metering device is used.

Ten-year limited warranty.

Aspen CC24A2G-145L-059

STANDARD SPECIFICATIONS

Rifled copper tubing, enhanced aluminum fins.

Immersion-tested at 500 psi, then nitrogen-pressurized and sealed.

Left- or right-hand refrigerant and plumbing connections.

Liquid line - 3/8 ODS, suction line - 3/4 ODS on 1-1/2- 3 ton & 7/8 ODS on 3-1/2 - 5 ton.

Externally mounted flowrater body with Schrader valve for hiss-testing.

Heavy duty plastic drain pans on most models.

Upflow without field modification. Downflow applications require plate kit, included.

AHRI certifiable with all brands of A/C and heat pump systems.

ETL listed for use with both R-22 and R-410a when proper metering device is used.

Ten-year limited warranty.

Aspen CC36A2G-175L-059

STANDARD SPECIFICATIONS

Rifled copper tubing, enhanced aluminum fins.

Immersion-tested at 500 psi, then nitrogen-pressurized and sealed.

Left- or right-hand refrigerant and plumbing connections.

Liquid line - 3/8 ODS, suction line - 3/4 ODS on 1-1/2- 3 ton & 7/8 ODS on 3-1/2 - 5 ton.

Externally mounted flowrater body with Schrader valve for hiss-testing.

Heavy duty plastic drain pans on most models.

Upflow without field modification. Downflow applications require plate kit, included.

AHRI certifiable with all brands of A/C and heat pump systems.

ETL listed for use with both R-22 and R-410a when proper metering device is used.

Ten-year limited warranty.

Aspen CC42AG-210L-059

STANDARD SPECIFICATIONS

Rifled copper tubing, enhanced aluminum fins.

Immersion-tested at 500 psi, then nitrogen-pressurized and sealed.

Left- or right-hand refrigerant and plumbing connections.

Liquid line - 3/8 ODS, suction line - 3/4 ODS on 1-1/2- 3 ton & 7/8 ODS on 3-1/2 - 5 ton.

Externally mounted flowrater body with Schrader valve for hiss-testing.

Heavy duty plastic drain pans on most models.

Upflow without field modification. Downflow applications require plate kit, included.

AHRI certifiable with all brands of A/C and heat pump systems.

ETL listed for use with both R-22 and R-410a when proper metering device is used.

Ten-year limited warranty.

Aspen CC48A2G-210L-059

STANDARD SPECIFICATIONS

Rifled copper tubing, enhanced aluminum fins.

Immersion-tested at 500 psi, then nitrogen-pressurized and sealed.

Left- or right-hand refrigerant and plumbing connections.

Liquid line - 3/8 ODS, suction line - 3/4 ODS on 1-1/2- 3 ton & 7/8 ODS on 3-1/2 - 5 ton.

Externally mounted flowrater body with Schrader valve for hiss-testing.

Heavy duty plastic drain pans on most models.

Upflow without field modification. Downflow applications require plate kit, included.

AHRI certifiable with all brands of A/C and heat pump systems.

ETL listed for use with both R-22 and R-410a when proper metering device is used.

Ten-year limited warranty.

Aspen CC60B34-210L-184

STANDARD SPECIFICATIONS

Rifled copper tubing, enhanced aluminum fins.

Immersion-tested at 500 psi, then nitrogen-pressurized and sealed.

Left- or right-hand refrigerant and plumbing connections.

Liquid line - 3/8 ODS, suction line - 3/4 ODS on 1-1/2- 3 ton & 7/8 ODS on 3-1/2 - 5 ton.

Externally mounted flowrater body with Schrader valve for hiss-testing.

Heavy duty plastic drain pans on most models.

Upflow without field modification. Downflow applications require plate kit, included.

AHRI certifiable with all brands of A/C and heat pump systems.

ETL listed for use with both R-22 and R-410a when proper metering device is used.

Ten-year limited warranty.

Aspen CC36A2G-210L-059

STANDARD SPECIFICATIONS

Rifled copper tubing, enhanced aluminum fins.

Immersion-tested at 500 psi, then nitrogen-pressurized and sealed.

Left- or right-hand refrigerant and plumbing connections.

Liquid line - 3/8 ODS, suction line - 3/4 ODS on 1-1/2- 3 ton & 7/8 ODS on 3-1/2 - 5 ton.

Externally mounted flowrater body with Schrader valve for hiss-testing.

Heavy duty plastic drain pans on most models.

Upflow without field modification. Downflow applications require plate kit, included.

AHRI certifiable with all brands of A/C and heat pump systems.

ETL listed for use with both R-22 and R-410a when proper metering device is used.

Ten-year limited warranty.

Aspen CC30A2G-145L-059