Diversitech DDS-60 Metal Fusible Pull-Out Disconnect Switch, 60 amp at 240 VAC

• Convenient design allows for easy access to controls via wide-opening, reversible door with full dead front
• Fused models benefit from having fuses located in easy pull-out handle with indicator lights for blown fuses
• Line, load and ground terminals aligned for easy wiring
• Folding pullout handle - low profile
• Folding pivot locking tab
• Installs without removing internals
• This is rain tight and sleet resistant

Sid Harvey Item #:E348-22: Replaces Part #:'s : 14043 | 14045 |,
,

Diversitech E348-22

Sid Harvey E306-45 #10 Kwik-Fit Electrical Wiring Harness, 6 feet L x 1/2 Inch Dia.

• Liquid tight
• Includes (1) each, straight and 90 deg connectors
• Metal connections attached

Sid Harvey Item #:E306-45: Replaces Part #:'s : 7211,
,

Sid Harvey E306-45

Sid Harvey E306-40 #10 Kwik-Fit Electrical Wiring Harness, 4 feet L x 1/2 Inch Dia.

• Liquid tight
• Includes (1) each, straight and 90 deg connectors
• Metal connections attached

Sid Harvey Item #:E306-40:,
,

Sid Harvey E306-40

COMPATIBILITY  Compatible with 85% of households:

24V heating and cooling systems, including furnaces, air conditioners, boilers, and heat pumps with either forced air or radiant delivery.

Conventional systems that have one stage of heating and cooling and a second stage of either heating or cooling.

Heat pumps that have one stage of heating and cooling and either aux or emergency heat.HVAC fans

Designed to work if your home doesn't have a common ("C") wire. In some cases, particularly if you have a heating or cooling-only system or use a zone controller, a C wire or other power-supply accessory may be necessary.,
,

The Stock Market GGA02180US

Diversitech HP3636-8 Heat Pump Riser Pad 36" L x 36" W x 8" H for Use With Heat Pump Equipment
Provides an effective base for heat pump equipment installed in snowy climates. Rather than a combination of a typical 2" (or 3") equipment pad and 6in. Heat pump risers, the Heat Pump Pad provides a full 8" of elevation in a simple square footprint. The star pattern of the integral risers allows for installation of equipment with different size footprints up to 36 x 36". Also included are eight anti-vibration pads uniquely designed to fit into the guide slots on the top of the integral risers. The base is sloped outward to allow for easy drainage of condensate or defrost cycle condensate when the outdoor coil is operating in heat pump mode. Nestable for efficient shipping, transportation, and warehousing. Injection molded from concrete gray, recycled polypropylene material, the Heat Pump Pad is environmentally friendly and designed to last longer than the equipment it supports. US Patent Number 7,891,635, and other patent(s) pending.

,
,

Diversitech HP3636-8

Diversitech HPR-6 1-Piece Heat Pump Riser
DiversiTech's Heat Pump Riser provides the desired elevation for condensers, heat pumps, and air handlers. The one-piece, heavy-duty plastic unit is manufactured in three heights. Butyl mastic on the top and bottom guarantees no slipping and reduced vibration and noise. Available in 1 or 2 piece risers. Four risers can handle up to 2,000 lb uniform load.,

Diversitech HPR-6

Diversitech HPR-3 1-Piece Heat Pump Riser
DiversiTech's Heat Pump Riser provides the desired elevation for condensers, heat pumps, and air handlers. The one-piece, heavy-duty plastic unit is manufactured in three heights. Butyl mastic on the top and bottom guarantees no slipping and reduced vibration and noise. Available in 1 or 2 piece risers. Four risers can handle up to 2,000 lb uniform load.,
,

Diversitech HPR-3

Diversitech HP3232-8 Heat Pump Riser Pad 32" L x 32" W x 8" H for Use With Heat Pump Equipment
Provides an effective base for heat pump equipment installed in snowy climates. Rather than a combination of a typical 2" (or 3") equipment pad and 6in. Heat pump risers, the Heat Pump Pad provides a full 8" of elevation in a simple square footprint. The star pattern of the integral risers allows for installation of equipment with different size footprints up to 36 x 36". Also included are eight anti-vibration pads uniquely designed to fit into the guide slots on the top of the integral risers. The base is sloped outward to allow for easy drainage of condensate or defrost cycle condensate when the outdoor coil is operating in heat pump mode. Nestable for efficient shipping, transportation, and warehousing. Injection molded from concrete gray, recycled polypropylene material, the Heat Pump Pad is environmentally friendly and designed to last longer than the equipment it supports. US Patent Number 7,891,635, and other patent(s) pending.

,
,

Diversitech HP3232-8

Lux Products PSP511LC Programmable Thermostat

• 5-2 Day 1 H/1 C 24-30 VAC 45-90 Deg,
  ,
  

  Lux Products PSP511LC

Lux Products PSP511C Programmable Thermostat

• 5-2 Day 1 H/1 C 24-30 VAC 45-90 Deg,
  ,
  

  Lux Products PSP511C