Baked-On Powder Coated Hydronic Air Handler with TXV Metering

• Multi function micro-processor circuit board
• Blower start relay - eliminates field installed boiler relay, allowing direct wiring from the boiler to the air handler
• Manual air vent on hot water coil
• Blower door shut-off switch
• Slide out hot water coil for easier service
• 2-speed fan operation
• Convertible horizontal drain pan
• PisTon type metering device (standard)
• Copper tube heating and cooling coils
• Compatible with all major brands of split condensing units and heat pumps
• Primary and secondary condensate drain connections
• Factory installed filter drier
• 1" filter easily accessible
• Without pump

  First Company 60HBXB-HW-R410A-TXV

Mars 84135 Non-Metallic Whip 1/2" x 6',
,

Motors & Armatures 84135

Fujitsu FH6024TTSASN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections

Fujitsu FH6024TTSASN

Fujitsu FH4824TPSJSN 1-Stage Standard Efficiency 95% Non-Communicating Air Handler
The most compact unit design available, all standard heat airhandler models only 421/2 to 57"es [1079 to 1448 mm] high. Attractive pre-painted cabinet exterior. Rugged wall steel cabinet construction, designed for added strength and versatility. 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance. Four leg blower motor mount. Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience. Traditional open wire element design for heat applications. Field convertible for vertical downflow, horizontal left hand or right hand air supply. 3 combustible floor base accessories fit all model sizes when required for downflow installations on combustible floors. Indoor coil design provides low air side pressure drop, high performance and extremely compact size. Expansion valve on indoor coil provides for operation with air conditioning or heat pump using the same coil. Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing. Coils are tested at the factory with an extensive refrigerant leak check.Coils have copper sweat refrigerant connections.Coils utilize chatleff metering device connections. Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils. Supply duct flanges provided as standard on air handler cabinet. Provisions for field electrical, connections available from either side or top of the air handler cabinet. Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet. Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2"es [51 mm] for 11/2" [38 mm] conduit. Front refrigerant and drain connections

Fujitsu FH4824TPSJSN

REFRIGERATION CIRCUIT

Copeland Scroll Ultratecht compressors on all models

Crankcase Heater factory installed

Suction line accumulator factory installed

Bi- flow filter- drier included for field installation

Integrated solid state control with Time- Temperature Defrost

High and low pressure switches

Discharge gas thermostat

Copper tube / aluminum fin coil PERFORMANCE

Self configuring installation capabilities with Observer Communicating Wall Control

Outdoor temperature sensor factory installed

Ball Bearing PSC Fan Motors on all models

High performance compressor sound shield standard

Isolation compressor grommets
EASY TO INSTALL AND SERVICE

Text based diagnostics with Observer Communicating Wall Control

Only 2 control wires required from communicating indoor unit to condenser

Easy access service valves on all models

Innovative control box design

External high and low refrigerant service ports

Only two screws to access control panel

Factory charged with R- 410A refrigerant
BUILT TO LAST

High gloss, baked- on powder coat finish over galvanized steel

Post- painted (black) coil fins

Coated, weather- resistant cabinet screws

Coated inlet grille with 3/8 (10mm) spacing for extra protection (hail guard)

Corner posts for extra strength and style

International Comfort Products

Tempstar TCH636GK