S2K Commerce - Products Dropdown
Actions
S2K Commerce - Shopping Cart
Actions
S2K Commerce - Order Entry
Actions
Brand Name
Part Type
Wayne Combustion Parts 56671-WYN1 EC-50K Repair kit
Wayne Combustion Parts 56671-WYN1
Item#:
56671-WYN1
Manufacturer Item:
56671-WYN1
Manufacturer:
WAYNE WATER SYSTEMS
Flow Rate
Atomizing nozzles are available in a wide range of flow rates, all
but eliminating the need for specially calibrated nozzles. Between
1.00 GPH and 2.00 GPH, for example, seven different flow rates
are available. Generally, with hot water and warm air heat, the
smallest firing rate that will adequately heat the house on the
coldest day is the proper size to use and the most economical.
Short on-cycles result in low efficiency. Another guideline is to
select the flow rate that provides a reasonable stack temperature
regardless of the connected load. (According to the New England
Fuel Institute, aim for a stack temperature of 400°F or lower on
matched packaged units or 500°F or lower on conversion burners.)
If the boiler or furnace is undersized for the load, it may be
necessary to fire for the load and ignore the efficiency
Spray Angle
Spray angles are available from 30° through 90° in most nozzle
sizes to meet the requirements of a wide variety of burner air
patterns and combustion chambers.
Usually it is desirable to fit the spray angle to the air pattern of the
burner. In todays flame retention burner, it is possible to fire more
than one spray angle with good results. Generally, round or square
combustion chambers should be fired with 70° to 90° nozzles.
Long, narrow chambers usually require 30° to 60° spray angles.
Burner Air Patterns
Burner air patterns are much like nozzle spray patterns in that
they fall into the same general classifications, either hollow or
solid. As you would expect, a burner with a hollow air pattern
generally requires a hollow cone fuel nozzle. A burner with a solid
air pattern will give highest efficiency with a solid cone nozzle,
but the flame will probably be longer.
Spray Angle
0.45 GPH .45-80H-FD
Item#:
7747028943
Manufacturer Item:
7-747-028-943
Manufacturer:
BOSCH THERMOTECHNOLOGY CORP
Flow Rate
Atomizing nozzles are available in a wide range of flow rates, all
but eliminating the need for specially calibrated nozzles. Between
1.00 GPH and 2.00 GPH, for example, seven different flow rates
are available. Generally, with hot water and warm air heat, the
smallest firing rate that will adequately heat the house on the
coldest day is the proper size to use and the most economical.
Short on-cycles result in low efficiency. Another guideline is to
select the flow rate that provides a reasonable stack temperature
regardless of the connected load. (According to the New England
Fuel Institute, aim for a stack temperature of 400°F or lower on
matched packaged units or 500°F or lower on conversion burners.)
If the boiler or furnace is undersized for the load, it may be
necessary to fire for the load and ignore the efficiency
Spray Angle
Spray angles are available from 30° through 90° in most nozzle
sizes to meet the requirements of a wide variety of burner air
patterns and combustion chambers.
Usually it is desirable to fit the spray angle to the air pattern of the
burner. In todays flame retention burner, it is possible to fire more
than one spray angle with good results. Generally, round or square
combustion chambers should be fired with 70° to 90° nozzles.
Long, narrow chambers usually require 30° to 60° spray angles.
Burner Air Patterns
Burner air patterns are much like nozzle spray patterns in that
they fall into the same general classifications, either hollow or
solid. As you would expect, a burner with a hollow air pattern
generally requires a hollow cone fuel nozzle. A burner with a solid
air pattern will give highest efficiency with a solid cone nozzle,
but the flame will probably be longer.
Spray Angle
0.55 GPH .55-90HDFN
Item#:
7747028944
Manufacturer Item:
7-747-028-944
Manufacturer:
BOSCH THERMOTECHNOLOGY CORP
U.S. Boiler Heating Parts 103339-01 Flame Sensor Kit for Alpine Hot Water Boilers
U.S. Boiler Heating Parts 103339-01
Item#:
103339-01
Manufacturer Item:
103339-01
Manufacturer:
U.S. BOILER COMPANY INC.
U.S. Boiler Heating Parts 105880-01 Flame Rod Sensor
105880-01
Item#:
105880-01
Manufacturer Item:
105880-01
Manufacturer:
U.S. BOILER COMPANY INC.
U.S. Boiler Heating Parts 103005-01 Igniter with Gasket Kit for Alpine 080 - 399 Gas fired Hot Water Boiler
103005-01
Item#:
103005-01
Manufacturer Item:
103005-01
Manufacturer:
U.S. BOILER COMPANY INC.
U.S. Boiler Heating Parts 109646-01 IQ Oil Boiler Control (Cold Start) Burnham
U.S. Boiler Heating Parts 109646-01
Item#:
109646-01
Manufacturer Item:
109646-01
Manufacturer:
U.S. BOILER COMPANY INC.
Peerless Boiler Parts 54714 Control Board
54714
Item#:
54714
Manufacturer Item:
54714
Manufacturer:
PB HEAT, LLC
Crown Boiler Parts 961122 Rollout Switch 240 Degrees
Crown Boiler Parts 96-023
Item#:
961122
Manufacturer Item:
961122
Manufacturer:
CROWN BOILER COMPANY
Heat Controller Heating Parts 17B0001N04C Control Board
17B0001N04C
Item#:
17B0001N04C
Manufacturer Item:
17B0001N04C
Manufacturer:
ICP FAST PARTS
White Rodgers Cooling Controls 50T35-743 Circuit Board
White Rodgers 50T35-743
White Rodgers 50T35-743
White Rodgers 50T35-743
Item#:
50T35-743
Manufacturer Item:
B1809913S
Manufacturer:
WHITE-RODGERS DIV OF COPELAND
Bosch Inducer Motor 8733952465 Inducer
Bosch Inducer Motor 87182261850
Item#:
8733952465
Manufacturer Item:
8-733-952-465
Manufacturer:
BOSCH THERMOTECHNOLOGY CORP