Test Products International A761

Honeywell CHWE41013

• Conveniently place near sinks, washers, water heaters, sump pumpsanywhere leaks could happen. Battery life lasts up to 3 years without incident
• Notification messages can alert you or your family/ friends, wherever you are, while audible (100 dB alarm) alerts sound when you are at home
• Use to detect temperatures that can freeze pipes, and humidity that could damage valuables
• Runs on WiFi - No Extra Hub or hardware purchase required
• Daisy chain extra cable sensors and cover up to 500 feet of space with one leak detector
• Reusable even after detecting an incident
• After an alarm, simply wipe dry the detector and cable sensors and place them back into service
• There is a 5 years warranty for professionally installed devices
• Mounting - Insert the plug from the cable sensor into the cable sensor jack at the end of the previous cable sensor, repeat for additional cable sensors up to a limit of 500 feet of cable sensors

Resideo CHWES41013

• Fast-Stat wiring extenders electronically add more wires to a control cable
• Saves significant time and expense as compared to repulling of new cables
• Causes no damage to walls or ceilings as compared to access holes that are often needed when re-pulling cables
• The sender and receiver communicate over the existing thermostat cable and/or outdoor unit cable
• Not a wireless system and therefore avoids all the problems that wireless systems may have
• No batteries required, all Fast-Stat models are powered by the existing 24 VAC transformer
• Works with old and new systems, can be connected to older systems such as thermopile milliVAC, standing pilot systems, intermittent pilot controllers, fan centers, etc.
• Fast-Stat wiring extenders do not produce interference with other electronic devices nor are they affected electronic devices that produce large amounts of interference
• Many Fast-Stat wiring extenders can be used in the same building or complex without interference between units
• Low power use, most FAST-STAT models use less than 3 watt of power

Fast-Stat COMMON MAKER

• Mount on return duct for backup control of non-zoned RedLink enabled wireless systems and thermostats
• Takes control of the equipment by turning on the blower fan and sensing the indoor temperature of the home
• Provides homeowners with peace of mind
• Installs in minutes

Honeywell C7735A1000

• The remote indoor temperature sensor is used to sense temperature remotely
• Used to sense temperature if the thermostat is installed in a poor temperature sensing location
• Small remote temperature sensor to match any room decor
• Easy to install and use
• Factory calibrated, no field calibration required
• Mounts directly on the wall using mounting screws and anchors provided
• Maximum distance between thermostat and sensor is 200 feet

Honeywell C7189U1005

Johnson Controls C450CPN-4C

• Powered by RedLINK reliability
• No interference with other wireless devices in the home
• Reliable performance in all climates
• Installs in minutes
• Up to 5 years battery life
• 2 months low battery warning
• Battery warning displayed on RedLINK enabled thermostats
• Used with RedLINK enabled thermostats and accessories
• Vertical mounting with supplied bracket and mounting hardware
• Thermistor sensor element
• - 1% RH condensing

Honeywell C7089R1013

Honeywell C7189R2002-2

• The Honeywell Home ERM is like a new cordless tool in your toolbox, pull it out whenever it's too costly or time-consuming to run wires from a condensing unit or boiler to control devices
• There are fewer holes to drill and wires to run, just faster, easier installation that gives you more profit per job, make the Honeywell Home ERM your go-to choice for fast, easy equipment installation
• Eliminates the need to run additional wires to your equipment, for example during a heat pump upgrade
• Suitable for outdoor use
• Temperature sensor terminals for outdoor temp sensors or indoor freeze protection
• LED for easy installation checkout
• May reduce damage to homes since wiring/drilling is eliminated
• Attach the ERM to the wall near the compressor or boiler, the location should be at least 3 feet above ground and oriented with the 2-wire exits facing downward mounting
• Compressor, boiler connected LEDs

Honeywell ERM5220R1018