Parker C-EC-SC Series Balance Ported Thermostatic Expansion Valve Body

• 3/8" x 1/2" ODF
• 1/2-1 HP, R404A
• The SC(E) series brass body expansion valve incorporates a 90 deg elbow inlet with a removable strainer
• External

,
,

Parker SCE-A-SW

Parker C-EC-SC Series Balance Ported Thermostatic Expansion Valve Body

• 3/8" x 1/2" ODF
• 1/2-1 HP, R404A
• The SC(E) series brass body expansion valve incorporates a 90 deg elbow inlet with a removable strainer
• External

,
,

Parker SCE-A-SZ

Parker SORIT-PI-29S-0/100 Evaporator Pressure Regulating Valve 1-1/8" OD 0/100 psi

Parker SORIT20

Parker SORIT-PI-311S-0/100 Evaporator Pressure Regulating Valve 1-3/8" OD 0/100 psi

Parker SORIT-PI-29S-0/100

Parker commercial pressure regulator (S)PORT/(S)PORTII valves are designed with stainless steel bonnet bolts, adjusting stems, and pisTon and plug assemblies. The result is a regulator designed to withstand the rigorous application environment a low side regulator must endure. Models are available in combinations of connection sizes, port sizes and features as designated by the model code. Unlike some competitive models of low side regulators that utilize high pressure discharge gas as a pilot source, they are piloted with upstream pressure. This eliminates the requirement for hot gas headers, isolation devices, piping, and the labor associated with the installation of other valves. Flare connections from high pressure pilot lines are also eliminated, minimizing sources for prospective leaks. The valves are an integrated assembly of (4) modules: 1) a body, which contains no moving parts, 2) a capacity cartridge, which contains both pisTon and modulating plug, and defines the port size and onto which the pilot solenoids providing the"S" (shut-off) or"B" (bypass) features are added as required, 4) the bonnet, containing the range spring and adjustment screw, which is set for the value of pressure which the valve is to maintain. The unique modular design allows the regulator to be soldered into the line without disassembly, yet provides full access for disassembly, cleaning and servicing from the top only. Interchangeable capacity cartridges facilitate flow revisions should an undersized or oversized condition be encountered, while pilot adapters can be changed out to add features or even change functions.

• Retrofitting for additional evaporator capacity is simple and requires no pipe line revisions
• The pisTon and plug assembly can handle reduced flow conditions and controlling down to about 15% of the valve's maximum capacity
• 2-5/8" OD
• Designed entirely with corrosion resistant materials
• New cooler running coil and open frame coil housing
• New dual VAC age 208/240/60 Hz coil
• Conveniently located access fitting
• Pilot operated for close control at desired set-point
• Excellent regulation at light loads
• Interchangeable capacity cartridges
• Low pressure drop
• Few moving parts
• Long-life stainless steel diaphragms (no bellows to fail)
• Pilot electric shut-off
• All service from the top
• Sweat-in-place without disassembly

,

Parker SPORT-09-09

Parker Suction Line Filter Drier

• Solid Core, Activated Alumina Suction Line Filter Dryer.
  
  • High Acid Capacity
    
    • Low Pressure Drop
      
      • Designed for System Clean-Up
        
        • 500 Hours Salt Spray Protection
          
          
          
          

          Parker SLD27-7SVHH

Parker evaporator Pressure Regulating Valves are mechanical regulators which use highside system pressure as a source of operating power. They were developed specifically for systems where accurate control and minimum pressure drop are important requirements.1-1/8" OD

Uses MKC-1/PKC1 Coils
,
,

Parker SORIT12

Parker evaporator Pressure Regulating Valves are mechanical regulators which use highside system pressure as a source of operating power. They were developed specifically for systems where accurate control and minimum pressure drop are important requirements.1-5/8" OD

Uses MKC-1/PKC1 Coils,
,

Parker SORIT15

Parker SORIT-PI-411S-0/100 Evaporator Pressure Regulating Valve 1-3/8" OD

SORIT-PI-411S-0/100

Parker Powder Painted Steel Gold Label Liquid Line Filter Drier

• 1/2" OD
• 8 Cube
• 10 Micron
• Solid copper connections
  
• Unsurpassed Moisture and Acid Capacities Maximum Filtration Capability for Today's Systems.
• Compatible with Mineral Oil, Alkybenzene and POE Lubricants Solid Molecular Sieve Core.
• Made in the USA
• Unsurpassed moisture capacity and maximum filtration capability for todays systems
• Compatible with all commercially available refrigerants including R-410A
• Compatible with mineral oil, alkybenzene and POE lubricants
• Solid molecular sieve core
• Solid copper ODF solder fittings and nickel plated steel SAE fittings
• Powder paint exterior coating surpasses 500 hour ASTM salt spray test to resist corrosion
• Maximum Rated Pressure of 650 psig (44.8 bar).
• UL Listed under SMGT/SMGT7-SA1756,
  ,
  
  
  
  

  Henry Technologies SH-9105 OEM

Parker Valve 184005 Body Socket

Parker 183376

Parker 183376 Fitting Adapter for B17-091 Thermal Expansion Valve Kit, 1/2 x 3/8", OD x SAE Male Flare

,
,

Parker 183375