Home  > CONDENSER PADS(x)
View:
Diversitech EcoPad EP2424-2 Equipment Pad, 24 Inch L x 24 Inch W x 2 Inch D, Plastic, Domestic
  • 173 lb estimated allowable load
  • Used mainly as a base pad for ground supported equipment
  • Unlike other plastic pads, EnviroPad rugged design provides uniform and generous ribbing for optimum self-leveling ground support without inserts
  • The pads should be installed on roughly leveled soil or ground
  • EnviroPad equipment pads, due to their plastic composition, are not recommended for use in applications requiring pad contact with excessive heat or open flame
  • Enclosed is a table showing the allowable load estimates
  • Both 2 and 3 Inch pads have the same weight capacity
Item#:
EP2424-2
Manufacturer Item:
EP2424-2
Manufacturer:
CONDENSER PADS
EcoPad equipment pads are made from injection molded plastic. Their application is mainly as a base pad for ground supported equipment. Unlike other plastic pads, EcoPad rugged design provides uniform and generous ribbing for optimum self-leveling ground support without inserts. The pads should be installed on roughly leveled soil or ground. EcoPad equipment pads, due to their plastic composition, are not recommended for use in applications requiring pad contact with excessive heat or open flame.
  • Outer edges have rounded corners with double-thick walls
  • Textured surface prevents equipment slippage
  • UV resistant and unaffected by weather
  • Uniform ribbing transfers load evenly
  • No cracking and less breakage than concrete
  • Drillable for securing equipment
  • Extremely durable, yet lightweight
  • Generous ribbing for optimum, self-leveling ground support
  • Made of recycled material
Item#:
EP3030-2
Manufacturer Item:
EP3030-2
Manufacturer:
CONDENSER PADS
Hef-T-Pad is an injection molded equipment pad created from high impact polypropylene with UV inhibitors making it easy to handle, yet durable and strong. It does not require any additional equipment for moving and handling. It is resistant to impact, ultra violet degradation and weathering and will not crack, ake or warp. The Hef-T-Pad is virtually impervious to climatic variations. It is drillable to permit installation of refrigerant and electrical lines under and through the pad and to allow equipment to be easily secured to the pad.
  • Stabilization flange - provides a wide perimeter that reduces sinking in soft soil under heavy load, both the flange and ribbing provide reinforcement for the corners
  • Drillable - thick walled polymer is suitable for drilling and screw fastening of equipment, line sets, and electrical connections
  • Simplistic, neutral gray color with the pad size and branding is clearly embossed on the pad surface
  • Textured surface provides good aesthetics and a non-skid surface
  • Pad size is molded into the side of the pad as well as the top surface for easy identification
  • Stabilization foot of Hef-T-Pad increases the surface area for bearing stabilization on soil, it reduces sinking in soft soil under heavy load and supports ribs providing structural support
  • Heavy duty
  • Stabilization flange flared out from outer walls
Item#:
X3232211
Manufacturer Item:
X3232211
Manufacturer:
CONDENSER PADS
Hef-T-Pad is an injection molded equipment pad created from high impact polypropylene with UV inhibitors making it easy to handle, yet durable and strong. It does not require any additional equipment for moving and handling. It is resistant to impact, ultra violet degradation and weathering and will not crack, ake or warp. The Hef-T-Pad is virtually impervious to climatic variations. It is drillable to permit installation of refrigerant and electrical lines under and through the pad and to allow equipment to be easily secured to the pad.
  • Stabilization flange - provides a wide perimeter that reduces sinking in soft soil under heavy load, both the flange and ribbing provide reinforcement for the corners
  • Drillable - thick walled polymer is suitable for drilling and screw fastening of equipment, line sets, and electrical connections
  • Simplistic, neutral gray color with the pad size and branding is clearly embossed on the pad surface
  • Textured surface provides good aesthetics and a non-skid surface
  • Pad size is molded into the side of the pad as well as the top surface for easy identification
  • Stabilization foot of Hef-T-Pad increases the surface area for bearing stabilization on soil, it reduces sinking in soft soil under heavy load and supports ribs providing structural support
  • Heavy duty
  • Stabilization flange flared out from outer walls
Item#:
X3636211
Manufacturer Item:
X3636211
Manufacturer:
CONDENSER PADS
Hef-T-Pad is an injection molded equipment pad created from high impact polypropylene with UV inhibitors making it easy to handle, yet durable and strong. It does not require any additional equipment for moving and handling. It is resistant to impact, ultra violet degradation and weathering and will not crack, ake or warp. The Hef-T-Pad is virtually impervious to climatic variations. It is drillable to permit installation of refrigerant and electrical lines under and through the pad and to allow equipment to be easily secured to the pad.
  • Stabilization flange - provides a wide perimeter that reduces sinking in soft soil under heavy load, both the flange and ribbing provide reinforcement for the corners
  • Drillable - thick walled polymer is suitable for drilling and screw fastening of equipment, line sets, and electrical connections
  • Simplistic, neutral gray color with the pad size and branding is clearly embossed on the pad surface
  • Textured surface provides good aesthetics and a non-skid surface
  • Pad size is molded into the side of the pad as well as the top surface for easy identification
  • Stabilization foot of Hef-T-Pad increases the surface area for bearing stabilization on soil, it reduces sinking in soft soil under heavy load and supports ribs providing structural support
  • Heavy duty
  • Stabilization flange flared out from outer walls
Item#:
X2436211
Manufacturer Item:
X2436211
Manufacturer:
CONDENSER PADS
Hef-T-Pad is an injection molded equipment pad created from high impact polypropylene with UV inhibitors making it easy to handle, yet durable and strong. It does not require any additional equipment for moving and handling. It is resistant to impact, ultra violet degradation and weathering and will not crack, ake or warp. The Hef-T-Pad is virtually impervious to climatic variations. It is drillable to permit installation of refrigerant and electrical lines under and through the pad and to allow equipment to be easily secured to the pad.
  • Stabilization flange - provides a wide perimeter that reduces sinking in soft soil under heavy load, both the flange and ribbing provide reinforcement for the corners
  • Drillable - thick walled polymer is suitable for drilling and screw fastening of equipment, line sets, and electrical connections
  • Simplistic, neutral gray color with the pad size and branding is clearly embossed on the pad surface
  • Textured surface provides good aesthetics and a non-skid surface
  • Pad size is molded into the side of the pad as well as the top surface for easy identification
  • Stabilization foot of Hef-T-Pad increases the surface area for bearing stabilization on soil, it reduces sinking in soft soil under heavy load and supports ribs providing structural support
  • Heavy duty
  • Stabilization flange flared out from outer walls
Sid Harvey Item #:X3030211: Replaces Part #:'s : CLPP3030E | 92120007 | A/C
Item#:
X3030211
Manufacturer Item:
X3030211
Manufacturer:
CONDENSER PADS
Hef-T-Pad is an injection molded equipment pad created from high impact polypropylene with UV inhibitors making it easy to handle, yet durable and strong. It does not require any additional equipment for moving and handling. It is resistant to impact, ultra violet degradation and weathering and will not crack, ake or warp. The Hef-T-Pad is virtually impervious to climatic variations. It is drillable to permit installation of refrigerant and electrical lines under and through the pad and to allow equipment to be easily secured to the pad.
  • Stabilization flange - provides a wide perimeter that reduces sinking in soft soil under heavy load, both the flange and ribbing provide reinforcement for the corners
  • Drillable - thick walled polymer is suitable for drilling and screw fastening of equipment, line sets, and electrical connections
  • Simplistic, neutral gray color with the pad size and branding is clearly embossed on the pad surface
  • Textured surface provides good aesthetics and a non-skid surface
  • Pad size is molded into the side of the pad as well as the top surface for easy identification
  • Stabilization foot of Hef-T-Pad increases the surface area for bearing stabilization on soil, it reduces sinking in soft soil under heavy load and supports ribs providing structural support
  • Heavy duty
  • Stabilization flange flared out from outer walls
Item#:
X3636311
Manufacturer Item:
X3636311
Manufacturer:
CONDENSER PADS
Hef-T-Pad is an injection molded equipment pad created from high impact polypropylene with UV inhibitors making it easy to handle, yet durable and strong. It does not require any additional equipment for moving and handling. It is resistant to impact, ultra violet degradation and weathering and will not crack, ake or warp. The Hef-T-Pad is virtually impervious to climatic variations. It is drillable to permit installation of refrigerant and electrical lines under and through the pad and to allow equipment to be easily secured to the pad.
  • Stabilization flange - provides a wide perimeter that reduces sinking in soft soil under heavy load, both the flange and ribbing provide reinforcement for the corners
  • Drillable - thick walled polymer is suitable for drilling and screw fastening of equipment, line sets, and electrical connections
  • Simplistic, neutral gray color with the pad size and branding is clearly embossed on the pad surface
  • Textured surface provides good aesthetics and a non-skid surface
  • Pad size is molded into the side of the pad as well as the top surface for easy identification
  • Stabilization foot of Hef-T-Pad increases the surface area for bearing stabilization on soil, it reduces sinking in soft soil under heavy load and supports ribs providing structural support
  • Heavy duty
  • Stabilization flange flared out from outer walls
Item#:
X3232311
Manufacturer Item:
X3232311
Manufacturer:
CONDENSER PADS
Hef-T-Pad is an injection molded equipment pad created from high impact polypropylene with UV inhibitors making it easy to handle, yet durable and strong. It does not require any additional equipment for moving and handling. It is drillable to permit installation of refrigerant and electrical lines under and through the pad and to allow equipment to be easily secured to the pad.
Sid Harvey Item #:X2424211: Replaces Part #:'s : CLPP2424E | 92120002 | A/C
Item#:
X2424211
Manufacturer Item:
X2424211
Manufacturer:
CONDENSER PADS
E-Lite is a plastic pad designed as a mounting base for air conditioning condensers. The rugged design provides uniform and generous ribbing for optimum, self-leveling ground support without inserts. E-Lite is injection molded from polypropylene, resulting in a pad that is lightweight, but not too light. A subtle texture prevents unit slide and presents a classic appearance, which is enhanced by rounded edges and a concrete gray color. Each pad is molded with its size in raised letters.
  • 205 lb estimated allowable load
  • Lightweight, yet rugged
  • Drillable for securing unit
  • Uniform ribbing transfers load evenly
  • Subtle texture resists unit slide
  • Freeze/thaw, flawless performance under the 25-cycle regimen specified by ASTM C67
  • Chemical resistance - does not crack, flake or warp when tested per ASTM D2299 with the following R-22 and R-134A, synthetic canine urine, compressor oil, salt solution, 20% by volume
Item#:
EL1838-3
Manufacturer Item:
EL1838-3
Manufacturer:
CONDENSER PADS
Diversitech EcoPad EP3636-3 Black Injection Molded Plastic Equipment Pad, EcoPad equipment pads are made from injection molded plastic. Their application is mainly as a base pad for ground supported equipment. Unlike other plastic pads, EcoPad rugged design provides uniform and generous ribbing for optimum self-leveling ground support without inserts. The pads should be installed on roughly leveled soil or ground. EcoPad equipment pads, due to their plastic composition, are not recommended for use in applications requiring pad contact with excessive heat or open flame.
Item#:
EP3636-3
Manufacturer Item:
EP3636-3
Manufacturer:
CONDENSER PADS
Diversitech UC1636-2 Polystyrene Foam (EPS) Equipment Pad, 36" L x 16" W x 2" T
  • Lightweight, it is easy for handling tasks on site
  • Performs extraordinarily well under strict testing criteria, it does not craze, soften, or delaminate
  • Durable, textured surface prevents equipment sliding
  • Absorbs and dampens vibration associated with normal operation of a condensing unit
  • Water vapor evaporates through the UltraLite, preventing the expansion of cracks
  • Flame resistant to heating caused by the compressor, additionally, the surface is resistant to heat from incidental torch flame during site installation
Item#:
UC1636-2
Manufacturer Item:
UC1636-2
Manufacturer:
CONDENSER PADS
View: