S2K Commerce - Products Dropdown
Actions
S2K Commerce - Shopping Cart
Actions
S2K Commerce - Order Entry
Actions
Resideo Y8610U Intermittent 1 or 2-Rod Natural Gas/LP Pilot Retrofit Kit for Gas-Fired Atmospheric Furnaces, 24 VAC
,
- Intermittent pilot retrofit kits save energy by converting atmospheric standing pilot systems to intermittent pilot
- Use with natural or LP gas
- Provides 100% pilot gas shutoff if pilot fails to light, after 6 min delay, trial for ignition is repeated
- Ignition trail/delay sequence is repeated until the appliance lights or call for heat is removed
- 2 sec flame failure response time
- 0 or 30 sec pre-purge time
- Ignition sequence - continuous retry, after trial for ignition, pilot gas shuts off for 5 min then another trial for pilot ignition takes place
- Typical gas control - VR8204, VR8304
- Ignition source - internal high voltage spark generator
- Ignition trials to lockout - continuous retry
- 1 amp pilot, 2 amp at 24 VAC maximum valve load
- Q345, Q3451 typical ignition hardware
- 15 or 90 sec lockout timing and ignition trial time
- VR8204, VR8304 typical gas control
,
honeywell y8610u4001
honeywell y8610u4001
Item#:
Y8610U4001
Manufacturer Item:
Y8610U4001
Manufacturer:
HONEYWELL
Item#:
ZD10X24
Manufacturer Item:
ZD10X24TZ
Manufacturer:
HONEYWELL
ZD24X8TZ Honeywell Home Square Parallel Blade 24 VAC
The ZD is a power close and spring open damper. It has a 24-volt motor used to control circulating air in HVAC systems and used when a normally-open damper is required. The ZD is typically used with the TrueZONE and other electronic zoning systems.
Honeywell ZD24X8TZ
The ZD is a power close and spring open damper. It has a 24-volt motor used to control circulating air in HVAC systems and used when a normally-open damper is required. The ZD is typically used with the TrueZONE and other electronic zoning systems.- Mechanical visual position indicator for damper status
- Solid construction using extruded aluminum frame and blades
- Parallel blade design for low leakage performance
- Simple, easy-to wire, two wire installation with a third wire option M4 for LED open only light
- Reliable, strong, 24 volt spring return motor
- Fail-safe, normally open operation
- Ordering instructions: order ZD (dimensions 1) x (dimensions 2), (motor is always mounted on dimensions 2 side) for example, ZD10x8 is a 10 x 8 Inch damper with the motor on the 8 Inch side, but a ZD8x10 is an 8 x 10 Inch damper that has the motor on the 10 Inch side
- Damper can be installed in any orientation (mounting side can be on either the bottom or the side of the duct)
- Motor or actuators mounting - side or top
- 30 sec power closed/10 sec spring return
- 90 deg angular rotation
Honeywell ZD24X8TZ
Item#:
ZD24X8TZ
Manufacturer Item:
ZD24X8TZ
Manufacturer:
HONEYWELL
ZD10X12TZ Honeywell Parallel Action Automatic Rectangular Blade Damper 10" x 12" 24 VAC Strong & Reliable 24 VAC Spring-Return Motor The ZD is a power close and spring open damper. It has a 24-volt motor used to control circulating air in HVAC systems and used when a normally-open damper is required. The ZD is typically used with the TrueZONE and other electronic zoning systems.
- Mechanical visual position indicator for damper status
- Solid construction using extruded aluminum frame and blades
- Parallel blade design for low leakage performance
- Simple, easy-to wire, two wire installation with a third wire option M4 for LED open only light
- Reliable, strong, 24 volt spring return motor
- Fail-safe, normally open operation
- Ordering instructions: order ZD (dimensions 1) x (dimensions 2), (motor is always mounted on dimensions 2 side) for example, ZD10x8 is a 10 x 8 Inch damper with the motor on the 8 Inch side, but a ZD8x10 is an 8 x 10 Inch damper that has the motor on the 10 Inch side
- Damper can be installed in any orientation (mounting side can be on either the bottom or the side of the duct)
- Motor or actuators mounting - side or top
- 30 sec power closed/10 sec spring return
- 90 deg angular rotation
ZD10X12TZ
Item#:
ZD10X12TZ
Manufacturer Item:
ZD10X12TZ
Manufacturer:
HONEYWELL
ZD8X16TZ Honeywell Home Square Parallel Blade 24 VAC
The ZD is a power close and spring open damper. It has a 24-volt motor used to control circulating air in HVAC systems and used when a normally-open damper is required. The ZD is typically used with the TrueZONE and other electronic zoning systems.
Honeywell ZD8X16TZ
The ZD is a power close and spring open damper. It has a 24-volt motor used to control circulating air in HVAC systems and used when a normally-open damper is required. The ZD is typically used with the TrueZONE and other electronic zoning systems.- Mechanical visual position indicator for damper status
- Solid construction using extruded aluminum frame and blades
- Parallel blade design for low leakage performance
- Simple, easy-to wire, two wire installation with a third wire option M4 for LED open only light
- Reliable, strong, 24 volt spring return motor
- Fail-safe, normally open operation
- Ordering instructions: order ZD (dimensions 1) x (dimensions 2), (motor is always mounted on dimensions 2 side) for example, ZD10x8 is a 10 x 8 Inch damper with the motor on the 8 Inch side, but a ZD8x10 is an 8 x 10 Inch damper that has the motor on the 10 Inch side
- Damper can be installed in any orientation (mounting side can be on either the bottom or the side of the duct)
- Motor or actuators mounting - side or top
- 30 sec power closed/10 sec spring return
- 90 deg angular rotation
Honeywell ZD8X16TZ
Item#:
ZD8X16TZ
Manufacturer Item:
ZD8X16TZ
Manufacturer:
HONEYWELL
Honeywell Home YERM5220R8321/U Programmable Equipment Remote Module with Thermostat, Up to 2 Heat/2 Cool Heat Pump or Conventional, 24 VAC
,
,
- The Honeywell Home ERM is like a new cordless tool in your toolbox, pull it out whenever it's too costly or time-consuming to run wires from a condensing unit or boiler to control devices
- There are fewer holes to drill and wires to run, just faster, easier installation that gives you more profit per job, make the Honeywell Home ERM your go-to choice for fast, easy equipment installation
- Eliminates the need to run additional wires to your equipment, for example during a heat pump upgrade
- Suitable for outdoor use
- Temperature sensor terminals for outdoor temp sensors or indoor freeze protection
- LED for easy installation checkout
- May reduce damage to homes since wiring/drilling is eliminated
- Attach the ERM to the wall near the compressor or boiler, the location should be at least 3 feet above ground and oriented with the 2-wire exits facing downward mounting
- ERM compressor, boiler connected LEDs
,
,
Honeywell YERM5220R8321
Honeywell YERM5220R8321
Item#:
YERM5220R8321
Manufacturer Item:
YERM5220R8321
Manufacturer:
HONEYWELL
ZD14X10TZ Honeywell Home Square Parallel Blade 24 VAC
The ZD is a power close and spring open damper. It has a 24-volt motor used to control circulating air in HVAC systems and used when a normally-open damper is required. The ZD is typically used with the TrueZONE and other electronic zoning systems.
Honeywell ZD14X10TZ
The ZD is a power close and spring open damper. It has a 24-volt motor used to control circulating air in HVAC systems and used when a normally-open damper is required. The ZD is typically used with the TrueZONE and other electronic zoning systems.- Mechanical visual position indicator for damper status
- Solid construction using extruded aluminum frame and blades
- Parallel blade design for low leakage performance
- Simple, easy-to wire, two wire installation with a third wire option M4 for LED open only light
- Reliable, strong, 24 volt spring return motor
- Fail-safe, normally open operation
- Ordering instructions: order ZD (dimensions 1) x (dimensions 2), (motor is always mounted on dimensions 2 side) for example, ZD10x8 is a 10 x 8 Inch damper with the motor on the 8 Inch side, but a ZD8x10 is an 8 x 10 Inch damper that has the motor on the 10 Inch side
- Damper can be installed in any orientation (mounting side can be on either the bottom or the side of the duct)
- Motor or actuators mounting - side or top
- 30 sec power closed/10 sec spring return
- 90 deg angular rotation
Honeywell ZD14X10TZ
Item#:
ZD14X10TZ
Manufacturer Item:
ZD14X10TZ
Manufacturer:
HONEYWELL
ZD14X8TZ Honeywell Home Square Parallel Blade 24 VAC
The ZD is a power close and spring open damper. It has a 24-volt motor used to control circulating air in HVAC systems and used when a normally-open damper is required. The ZD is typically used with the TrueZONE and other electronic zoning systems.
Honeywell ZD14X8TZ
The ZD is a power close and spring open damper. It has a 24-volt motor used to control circulating air in HVAC systems and used when a normally-open damper is required. The ZD is typically used with the TrueZONE and other electronic zoning systems.- Mechanical visual position indicator for damper status
- Solid construction using extruded aluminum frame and blades
- Parallel blade design for low leakage performance
- Simple, easy-to wire, two wire installation with a third wire option M4 for LED open only light
- Reliable, strong, 24 volt spring return motor
- Fail-safe, normally open operation
- Ordering instructions: order ZD (dimensions 1) x (dimensions 2), (motor is always mounted on dimensions 2 side) for example, ZD10x8 is a 10 x 8 Inch damper with the motor on the 8 Inch side, but a ZD8x10 is an 8 x 10 Inch damper that has the motor on the 10 Inch side
- Damper can be installed in any orientation (mounting side can be on either the bottom or the side of the duct)
- Motor or actuators mounting - side or top
- 30 sec power closed/10 sec spring return
- 90 deg angular rotation
Honeywell ZD14X8TZ
Item#:
ZD14X8TZ
Manufacturer Item:
ZD14X8TZ
Manufacturer:
HONEYWELL
ZD8X18TZ Honeywell Home Square Parallel Blade 24 VAC
The ZD is a power close and spring open damper. It has a 24-volt motor used to control circulating air in HVAC systems and used when a normally-open damper is required. The ZD is typically used with the TrueZONE and other electronic zoning systems.
Honeywell ZD8X18TZ
The ZD is a power close and spring open damper. It has a 24-volt motor used to control circulating air in HVAC systems and used when a normally-open damper is required. The ZD is typically used with the TrueZONE and other electronic zoning systems.- Mechanical visual position indicator for damper status
- Solid construction using extruded aluminum frame and blades
- Parallel blade design for low leakage performance
- Simple, easy-to wire, two wire installation with a third wire option M4 for LED open only light
- Reliable, strong, 24 volt spring return motor
- Fail-safe, normally open operation
- Ordering instructions: order ZD (dimensions 1) x (dimensions 2), (motor is always mounted on dimensions 2 side) for example, ZD10x8 is a 10 x 8 Inch damper with the motor on the 8 Inch side, but a ZD8x10 is an 8 x 10 Inch damper that has the motor on the 10 Inch side
- Damper can be installed in any orientation (mounting side can be on either the bottom or the side of the duct)
- Motor or actuators mounting - side or top
- 30 sec power closed/10 sec spring return
- 90 deg angular rotation
Honeywell ZD8X18TZ
Item#:
ZD8X18TZ
Manufacturer Item:
ZD8X18TZ/U
Manufacturer:
HONEYWELL
Equipment Interface Module controls up to 4-stages of heat and 2-stages of cool in a heat pump system and up to 3-stages of heat and 2-stages of cool in a conventional system. Three sets of Universal IAQ contacts to control humidification, dehumidification, and ventilation. Four sensor inputs for wired sensors or dry contact devices.,
,
,
Honeywell YTHM5421R1010
Honeywell YTHM5421R1010
ZD18X10 Honeywell Square Parallel Blade 24 VAC
The ZD is a power close and spring open damper. It has a 24-volt motor used to control circulating air in HVAC systems and used when a normally-open damper is required. The ZD is typically used with the TrueZONE and other electronic zoning systems.
Honeywell ZD18X10
The ZD is a power close and spring open damper. It has a 24-volt motor used to control circulating air in HVAC systems and used when a normally-open damper is required. The ZD is typically used with the TrueZONE and other electronic zoning systems.- Mechanical visual position indicator for damper status
- Solid construction using extruded aluminum frame and blades
- Parallel blade design for low leakage performance
- Simple, easy-to wire, two wire installation with a third wire option M4 for LED open only light
- Reliable, strong, 24 volt spring return motor
- Fail-safe, normally open operation
- Ordering instructions: order ZD (dimensions 1) x (dimensions 2), (motor is always mounted on dimensions 2 side) for example, ZD10x8 is a 10 x 8 Inch damper with the motor on the 8 Inch side, but a ZD8x10 is an 8 x 10 Inch damper that has the motor on the 10 Inch side
- Damper can be installed in any orientation (mounting side can be on either the bottom or the side of the duct)
- Motor or actuators mounting - side or top
- 30 sec power closed/10 sec spring return
- 90 deg angular rotation
Honeywell ZD18X10
Item#:
ZD18X10
Manufacturer Item:
ZD18X10TZ
Manufacturer:
HONEYWELL
Item#:
YTHX1200B6/U
Manufacturer Item:
YTHX1200B6/U
Manufacturer:
HONEYWELL