Field Controls OVD-6 Automatic Oil Vent Damper 6" Round

Field Controls OVD-6

Field Controls PPC-4 Thermal Post Purge Kit for CK-62 Control Kit

,
,

Field Controls PPC-4

All field vent hoods are made of heavy gauge aluminum and can be used with natural gas, LP gas or oil-fired equipment. There are five diameters ranging from 3 to 8 Inch. The concentric pipe, angled outlet deflectors, and spaced plate design allow for better heat dissipation. This type of construction minimizes the effects of heat on the outside wall. The angled hood design reduces the effects of wind on the venting system. The inner and outer pipe are a continuous structure. This allows for easy installation to power venter or vent pipe and also eliminates possible positive pressure leaks in the wall section.

• Can be used in conjunction with PVG and PVO power venters or with forced draft systems
• 7-5/8 x 7-5/8 shield for 0 clearance to combustible
• Designed for standard vent pipe and Class B type double-wall (B-Vent) connection
• Provides proper clearance between flue gas stream and wall combustible

Tjernlund 46235000 Stainless Steel Universal Replacement Motor Assembly, 6"

• Field Controls 46235000 Stainless Steel Universal Replacement Motor Assembly, 6",
  ,
  

  Tjernlund SWGII-6RMK

Installation of a spillage safety switch is recommended for LP and natural gas fired systems with draft hoods. This device is installed to detect flue gas spillage caused by a blocked flue system and/or inadequate draft. This device must be installed by a qualified installer in accordance with the manufacturer's installation instructions. Wiring must be in accordance with the National Electrical Code and applicable local codes.

• Efficiently detect flue gas spillage due to a blocked flue, continuous down drafting or inadequate draft condition
• With the safety switch wired in series with the burner circuit, the switch will de-energize the systems burner or burner control once it senses the spillage of hot flue gases
• Gold contact
• Includes (1) 6 feet length of 12/2 jacketed lead wire, (1) 8 feet length of 12 ga jumper wire, (3) adhesive tabs and switch jumper wire and (2) #8 self-drilling sheet metal screws

Sid Harvey Item #:SSK-3: Replaces Part #:'s : x71-204,
,

Field Controls SSK-3

Gas and oil heating appliances generate heat through the combustion of fuel. The heat is transferred through the heat exchanger and distributed to the conditioned space. The products of combustion, however, must be vented safely out of the structure. In a conventional chimney, venting is achieved by the natural lifting action of the hot combustion gas. New, efficient systems absorb more of the heat in the heat exchanger and produce lower temperature vent gas. Lower temperature gas does not rise as quickly or as reliably as in older, less efficient systems. Power venting or sidewall venting is more economical and safer than chimney venting. A power venter uses a motorized blower to vent the products of combustion. A power venter is interlocked with the appliance to ensure that proper draft is achieved before the appliance burner is activated.

• 100% negative pressure in the vent pipe for maximum safety
• Standard Galvanized pipe can be used instead of expensive stainless steel
• No need to seal vent pipe joints, saving time and money
• Significantly longer vent lengths than positive pressure, direct vent systems
• The SWG recommended by major heating appliance
• Thermal protected
• Power vent and backing plate included

,
,

Field Controls SWGII-4HD

Field Controls SWGII-6 Power Venter 6" 115 VAC,
,

Field Controls SWGII-6

Gas and oil heating appliances generate heat through the combustion of fuel. The heat is transferred through the heat exchanger and distributed to the conditioned space. The products of combustion, however, must be vented safely out of the structure. In a conventional chimney, venting is achieved by the natural lifting action of the hot combustion gas. New, efficient systems absorb more of the heat in the heat exchanger and produce lower temperature vent gas. Lower temperature gas does not rise as quickly or as reliably as in older, less efficient systems. Power venting or sidewall venting is more economical and safer than chimney venting. A power venter uses a motorized blower to vent the products of combustion. A power venter is interlocked with the appliance to ensure that proper draft is achieved before the appliance burner is activated.

• 100% negative pressure in the vent pipe for maximum safety
• Standard Galvanized pipe can be used instead of expensive stainless steel
• No need to seal vent pipe joints, saving time and money
• Significantly longer vent lengths than positive pressure, direct vent systems
• The SWG recommended by major heating appliance
• Thermal protected
• Power vent and backing plate included

Sid Harvey Item #:SWGII-5: Replaces Part #:'s : 39968,
,

Field Controls SWGII-5

Field Controls SWG-4HDS Stainless Steel Power Venter, 4", 115 VAC at 60 Hz, 1.7 amp, 138 watt The safest, most efficient power venter available today. Gas and oil heating appliances generate heat through the combustion of fuel. The heat is transferred through the heat exchanger and distributed to the conditioned space. The products of combustion, however, must be vented safely out of the structure. In a conventional chimney, venting is achieved by the natural lifting action of the hot combustion gas. New, efficient systems absorb more of the heat in the heat exchanger and produce lower temperature vent gas. Lower temperature gas does not rise as quickly or as reliably as in older, less efficient systems. Power venting or sidewall venting is more economical and safer than chimney venting. A power venter uses a motorized blower to vent the products of combustion. A power venter is interlocked with the appliance to ensure that proper draft is achieved before the appliance burner is activated.

• 100% negative pressure in the vent pipe for maximum safety
• Standard Galvanized pipe can be used instead of expensive stainless steel
• No need to seal vent pipe joints, saving time and money
• Significantly longer vent lengths than positive pressure, direct vent systems
• The SWG is recommended by major heating appliance manufacturers
• Thermal protected The safest, most efficient power venter available today. Gas and oil heating appliances generate heat through the combustion of fuel. The heat is transferred through the heat exchanger and distributed to the conditioned space. The products of combustion, however, must be vented safely out of the structure. In a conventional chimney, venting is achieved by the natural lifting action of the hot combustion gas. New, efficient systems absorb more of the heat in the heat exchanger and produce lower temperature vent gas. Lower temperature gas does not rise as quickly or as reliably as in older, less efficient systems. Power venting or sidewall venting is more economical and safer than chimney venting. A power venter uses a motorized blower to vent the products of combustion. A power venter is interlocked with the appliance to ensure that proper draft is achieved before the appliance burner is activated.Sid Harvey Item #:SWG-4HDS: Replaces Part #:'s : x89-857,
  ,
  

  Field Controls SWG-4HDS

Field Controls SWGII-5S Power Venter 5" 115 VAC 3k RPM 290k Btu Stainless Steel,
,

Field Controls SWGII-5S

The Field Controls steam humidifier is quite possibly the best humidifier for homes with forced air heat. It is compatible with virtually every make and model of forced air system, it is ideal for use with heat pumps, and will operate in the heating system without the need for a heat call. The humidifier that works when you need it. Automatic maintenance, information is power.

Field Controls S2020

Field Controls Portable 3-in-1 Air Purification System

Field Controls TRIO-1000P