Current Selected Location - Sid Harvey Garden City (0999) Garden City NY

For proper operation and efficient fuel consumption in oil, gas, and/or coal-fired heating appliances, draft must remain constant. When it is, combustion is more complete, fuels are utilized efficiently, and money is saved. Field Draft Controls maintain consistent draft by counteracting the negative forces caused by changes in temperature and barometric pressure, as well as the effects of wind.

• With collar

Sid Harvey Item #:100-20: Replaces Part #:'s : x71-179

Field Controls 46579100 GVD Universal Wiring Kit

Field Controls 46273100 Air Pressure Switch for CAS-3, CAS-4 and CK

The field RC is furnished as standard equipment on many leading brands of oil or coal-fired heating equipment. It is calibrated to allow for easy adjustment to the furnace or boiler manufacturer's specifications. Designed for settings from 0.02 - 0.08", this control is so sensitive that instrumentation should be used when adjusting the unit during installation.

Sid Harvey Item #:100-22: Replaces Part #:'s : x71-184

Field Controls 46144700 Post Purge Relay Timer for CAS-6, CAS-7 Combustion Air System Sid Harvey Item #:46144700: Replaces Part #:'s : 4G9025

The field RC is furnished as standard equipment on many leading brands of oil or coal-fired heating equipment. It is calibrated to allow for easy adjustment to the furnace or boiler manufacturer's specifications. Designed for settings from 0.02 - 0.08", this control is so sensitive that instrumentation should be used when adjusting the unit during installation.

Sid Harvey Item #:100-30: Replaces Part #:'s : x71-292

Field Controls Motor Assembly Base, for Use With GVD Vent Damper Motor, Plastic

Field Controls 46234800 Stainless Steel Universal Replacement Fan and Motor Assembly

• Includes replacement motor and blower wheel on mounting bracket (46275900 motor and 46310400 wheel), adapter plate (for SWG models), mounting fasteners, blower wheel depth gage, 1/8" hex wrench, tube of high temperature silicone sealant, instruction sheet

Sid Harvey Item #:46234800: Replaces Part #:'s : 6H090A

Field Controls (GVD) gas vent damper was developed to reduce off cycle venting losses through boilers and draft hoods. When the boiler is in a standby mode, heat escapes up the chimney. The heat comes from the boiler and the conditioned space. To significantly reduce these losses, install a Field Controls Gas Vent Damper. The damper is installed in the vent as close to the draft hood as practical. When properly installed, the damper opens before the burner fires, and closes after the burner shuts off. The electrical circuits in this product are designed not to override the existing limit and safety controls of the boiler.

• Operates with all 24 VAC , 60 Hz intermittent ignition and standing pilot ignition systems
• Stainless steel construction provides superior corrosion resistance
• Damper operation - power opens in 15 sec, power closes in 15 sec, power is off at damper motor when it is at rest
• Hold open switch allows damper to be placed in an open position and taken out of service to assist with trouble shooting appliance problems
• Keyed wiring harness connector plug installs only one way, preventing incorrect wiring connection
• Flex seal provides self cleaning action

Sid Harvey Item #:GVD-6PL: Replaces Part #:'s : 40703

Field Controls 02724001 Silver Barometric Draft Control for Gas-Fired Furnaces and Boilers is Widely Used for Conversion Burner Installations, Gas Atmospheric Appliances, 6"

• 28.3 sq-inch capacity
• 5 - 6" pipe size
• 24 ga (ring and gate), 26 ga (collar) thickness
• Because it is double acting, it opens out to relieve positive vent system pressures as low as 0.01"
• Can improve combustion stability and draft on many gas atmospheric installations with venting problems
• Provides precise, accurate control of drafts at levels higher than permitted by a standard draft diverter

Sid Harvey Item #:100-10: Replaces Part #:'s : 40573

Field Controls (GVD) gas vent damper was developed to reduce off cycle venting losses through boilers and draft hoods. When the boiler is in a standby mode, heat escapes up the chimney. The heat comes from the boiler and the conditioned space. To significantly reduce these losses, install a Field Controls Gas Vent Damper. The damper is installed in the vent as close to the draft hood as practical. When properly installed, the damper opens before the burner fires, and closes after the burner shuts off. The electrical circuits in this product are designed not to override the existing limit and safety controls of the boiler.

• Operates with all 24 VAC , 60 Hz intermittent ignition and standing pilot ignition systems
• Stainless steel construction provides superior corrosion resistance
• Damper operation - power opens in 15 sec, power closes in 15 sec, power is off at damper motor when it is at rest
• Hold open switch allows damper to be placed in an open position and taken out of service to assist with trouble shooting appliance problems
• Keyed wiring harness connector plug installs only one way, preventing incorrect wiring connection
• Flex seal provides self cleaning action

Field Controls CK-63 Control Kit for SWG Series Power Vent Hoods for Controlling Oil-fired Heating Appliances

• Control the operation of SWG/CV power venter
• Draft proving switch and secondary safety switch
• Adjustable electronic post-purge
• Includes mounted pressure switch and solid state post-purge control, (1) 2 feet length of 1/4" aluminum tubing, (1) 1/4" tubing connector, (1) flexible conduit connector, (1) WMO-1 secondary safety switch

Sid Harvey Item #:CK-63: Replaces Part #:'s : x71-291