ICM Controls ICM201 Delay-On-Make Timer, 18 - 30 VAC , 1.5 amp

Sid Harvey Item #:ICM201B: Replaces Part #:'s : ASC-500-5,
,

ICM Controls ICM201B

Diversitech HP3232-8 Heat Pump Riser Pad 32" L x 32" W x 8" H for Use With Heat Pump Equipment
Provides an effective base for heat pump equipment installed in snowy climates. Rather than a combination of a typical 2" (or 3") equipment pad and 6in. Heat pump risers, the Heat Pump Pad provides a full 8" of elevation in a simple square footprint. The star pattern of the integral risers allows for installation of equipment with different size footprints up to 36 x 36". Also included are eight anti-vibration pads uniquely designed to fit into the guide slots on the top of the integral risers. The base is sloped outward to allow for easy drainage of condensate or defrost cycle condensate when the outdoor coil is operating in heat pump mode. Nestable for efficient shipping, transportation, and warehousing. Injection molded from concrete gray, recycled polypropylene material, the Heat Pump Pad is environmentally friendly and designed to last longer than the equipment it supports. US Patent Number 7,891,635, and other patent(s) pending.

,
,

Diversitech HP3232-8

The DiversiTech HVENT-2 is a 2 in. horizontal termination kit that's used in venting high efficiency fossil fuel appliances. The low profile creates a simple and clean look while hiding both the intake and exhaust pipework.

Diversitech HVENT-2

The DiversiTech HVENT-2 is a 3 in. horizontal termination kit that's used in venting high efficiency fossil fuel appliances. The low profile creates a simple and clean look while hiding both the intake and exhaust pipework.

Diversitech HVENT-3

Diversitech MP-3C Rubber/Cork Equipment Pad, 3" L x 3" W x 7/8" H

• Highest quality elastomeric oil resistant padding
• Designed to withstand 50 psi
• Rubber pads are corrugated on both sides
• Cork is laminated between two corrugated pads

Sid Harvey Item #:J53-1: Replaces Part #:'s : 11507,

Diversitech J53-1

Diversitech MP-6C Rubber/Cork Equipment Pad, 6" L x 6" W x 7/8" H

• Highest quality elastomeric oil resistant padding
• Designed to withstand 50 psi
• Rubber pads are corrugated on both sides
• Cork is laminated between two corrugated pads

,

Diversitech J53-3

Diversitech MP-4C Rubber/Cork Equipment Pad, 4" L x 4" W x 7/8" H

• Highest quality elastomeric oil resistant padding
• Designed to withstand 50 psi
• Rubber pads are corrugated on both sides
• Cork is laminated between two corrugated pads

Sid Harvey Item #:J53-2: Replaces Part #:'s : 11511,
,

Diversitech J53-2

Diversitech MP-18 Rubber Equipment Pad, 18" L x 18" W x 3/8" H

• Highest quality elastomeric oil resistant padding
• Designed to withstand 50 psi
• Rubber pads are corrugated on both sides

Sid Harvey Item #:J53-5: Replaces Part #:'s : 11516
,
,

Diversitech J53-5

Diversitech JB8265 Epox-A-Leak Epoxy 2 Part System

J-B Weld JB8265 2-Part Steel Reinforced Epoxy Resin and Hardener, 1 oz The worlds finest cold-weld compound for use when welding or soldering is out of the question due to cost, down time for repairs or technical or environmental considerations. A remarkably easy, convenient and inexpensive alternative to welding, soldering, and brazing. Literally pennies per use.,
,

Diversitech JB8265

Diversitech MP-2C Rubber/Cork Equipment Pad, 2" L x 2" W x 7/8" H

• Highest quality elastomeric oil resistant padding
• Designed to withstand 50 psi
• Rubber pads are corrugated on both sides
• Cork is laminated between two corrugated pads

Sid Harvey Item #:J53: Replaces Part #:'s : 11505 | 11506 |
,
,

Diversitech J53

Diversitech K45-10 Vinyl Clear Tubing

• 7/8" x 50',
  ,
  

  Diversitech K45-10

Diversitech K45 Vinyl Clear Tubing 1/4" x 100'

Diversitech K45