M & G Duravent 4GVL90 0.012" Aluminum Inner and 0.018" GalvanizedSid Harvey Item #:4GVL90: Replaces Part #:'s : 19309,

4GVL90

,

4GVL90

M & G Duravent Lock-Tight 6GVL90 Gallonvanized Aluminum Type B Round Gas 90 Degree Elbow DuraVent's innovative system for a lock-tight connection for type B gas vent called DuraLock. See the alignment indicators meet, feel the ends grasp together, hear the snap as the connection firmly locks into place. DuraVent type B gas vent is designed to meet the rugged demands of the job site. The inner wall is recessed to eliminate damage in handling. Type B gas vent has been engineered to heat up rapidly. It remains hot during the operation of the appliance with minimal condensation in the appliance and vent system. Pipe lengths are available in multiple lengths, 6 - 60", with a full complement of adjustable and rigid fittings. Type B gas vents are not suitable for use with wood-burning or coal applications, industrial ovens, exhaust ranges and hoods, grease or pollution ducting or as free-standing exhaust vents for high-temperature applications.

• DuraVent's type B gas vent system, use with natural gas or liquid propane category I and draft hood equipped appliances and appliances tested and listed to use type B gas vent
• 1" clearance to combustibles in single and multi-family dwellings
• No sharp tabs to bend into slots, twist locks into place
• Designed to meet the rugged demands of the job site with a recessed inner wall
• Innovation system for a firm, lock-tight connection
• Engineered to heat-up rapidly
• Limited lifetime warranty DuraVent's innovative system for a lock-tight connection for type B gas vent called DuraLock. See the alignment indicators meet, feel the ends grasp together, hear the snap as the connection firmly locks into place. DuraVent type B gas vent is designed to meet the rugged demands of the job site. The inner wall is recessed to eliminate damage in handling. Type B gas vent has been engineered to heat up rapidly. It remains hot during the operation of the appliance with minimal condensation in the appliance and vent system.,
  
  

  6GVL90

  ,
  

  6GVL90

Duravent 4GVDC B-Vent Aluminum Cap 4",

4GVDC

,

4GVDC

Duravent 4GV24 B-Vent Pipe 4" x 24",

Duravent 4GV24

Sid Harvey 649 Chimney Insulation,

sid harvey 649

,

649

M & G DuraVent PolyPro 2PPC-HVKA Basic Horizontal Concentric Vent Kit, 2 and 4" Diameter

,

2PPC-HVKA

,

2PPC-HVKA

Duravent 4PPC-HVKA Concentric Horizontal Termination Kit 4"/6

4PPC-HVKA

All FasNSeal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on FasNSeal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All FasNSeal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

M & G Duravent FSELB9003

All FasNSeal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on FasNSeal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All FasNSeal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

• FasNSeal is for use with natural gas or propane categories II, III and IV appliances or type BH gas vent systems, having a maximum rated operating temperature of 480 deg F and a maximum positive pressure of 15" water column
• FasNSeal can be used on a wide range of applications, including high efficiency gas boilers, furnaces, booster heaters, pool heaters, water heaters, unit heaters or tankless water heaters
  
  
  M & G Duravent FSAVL3 Fas-n-Seal Adjustable Length Single Wall Gas Vent Pipe 3" x 18",
  
  
  

  Bugler Sales R7601EA

All FasNSeal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on FasNSeal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All FasNSeal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

M & G Duravent FSAVL4

All FasNSeal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on FasNSeal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All FasNSeal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

M & G Duravent FSBS3

Duravent FSBS4 Fas-n-Seal Bird Screen 4"

FSBS4