Home  > NU-CALGON(x)
|◀ 1 - 12 of 170 ▶|
View:
Nu-Calgon vacuum pump oil is a quality blend of high-grade lubricants, providing for oil that performs at the deepest vacuum. It lubricates to minimize wear and provide surface protection, and its high viscosity index assures adequate lubrication at high and low pressures. In addition, its broad package line guarantees the right package size for all levels of service activity, from the service professional handling only an occasional evacuation to the one conducting several every day.
Item#:
4383-24
Manufacturer Item:
4383-24
Manufacturer:
NU-CALGON
Nu-Calgon 4299-T8 Pump Protector, 10 oz Spray Can, Colorless Foam-in shut down corrosion protection for all types of pumps any pump that is shut down and drained part of the time should be safeguarded with aerosol pump protector. Pumps used in cooling towers, swimming pools and vacation homes, auxiliary pumps, marine and industrial pumps can develop corrosion deposits on the impeller and other close-tolerance areas during shut down, causing the pump to bind. Aerosol pump protector prevents this corrosion and lubricates the pump so that it starts right up every time! pump protector is water soluble and will not cause any foaming problem when the pump is started. If the pump is used for drinking water, flush it thoroughly by running water off a few minutes before placing the pump back in service. Protects seasonally operated pumps against corrosion during shutdowns by "winterizing" them. When corrosion occurs in close-tolerance areas, it can cause the impeller to stick or bind. Protect your clients investment and your reputation! Safe for all types of water pumps and it requires no special rinsing at start-up.
  • Protects against corrosion and ends-pump impeller binding
  • Convenient aerosol package
  • Safe for all types of water pumps
  • One can is enough for most pumps
  • Requires no special rinsing at startup
  • Protects pool pumps throughout the winter
  • This product has been authorized by the USDA for use in federally inspected meat and poultry plants
  • 95% volatile
  • Level 1 heat of combustion
  • 13 cm flame height, 4 - 5 sec flammability duration Foam-in shut down corrosion protection for all types of pumps any pump that is shut down and drained part of the time should be safeguarded with aerosol pump protector. Pumps used in cooling towers, swimming pools and vacation homes, auxiliary pumps, marine and industrial pumps can develop corrosion deposits on the impeller and other close-tolerance areas during shut down, causing the pump to bind. Aerosol pump protector prevents this corrosion and lubricates the pump so that it starts right up every time! pump protector is water soluble and will not cause any foaming problem when the pump is started. If the pump is used for drinking water, flush it thoroughly by running water off a few minutes before placing the pump back in service. Protects seasonally operated pumps against corrosion during shutdowns by "winterizing" them. When corrosion occurs in close-tolerance areas, it can cause the impeller to stick or bind. Protect your clients investment and your reputation! Safe for all types of water pumps and it requires no special rinsing at start-up.
Item#:
4299-T8
Manufacturer Item:
4299-T8
Manufacturer:
NU-CALGON
With technology installed in over 100,000 applications, iWave-R is the worlds first self-cleaning, no maintenance needlepoint bi-polar ionization generator designed specifically for treating air in residential duct A/C systems. As the air flows past the iWave-R, positive and negative ions actively purify the supply air, killing mold, bacteria and viruses in the coil and living space. The ionization process also reduces allergens, smoke and static electricity, as well as controlling odors (cooking, pet, VOCs) and other particles (no more sunbeams) in the air without creating ozone or any harmful byproducts. iWave-R treats the air in any brand of residential duct air conditioning systems up to 6 tons (2400 CFM) in size with no maintenance and no replacement parts. Designed for universal mounting, the iWave-R typically requires only 15 minutes to install inside or outside of duct, or to attach magnetically near the indoor fan in the air handler. Simply connect to power using its patent-pending VAC age input capability. Install between air filter and cooling coil to treat the indoor coil; as an alternative, the iWave-R can be installed in the supply air. iWave-R always works at peak performance, producing over 160 million ions/cc, more than any other ionizer product on the market. Its patent-pending self-cleaning design includes a programmable cleaning cycle that can clean the emitter brushes every 1, 3, 5 or 10 days. The iWave-R is factory set to clean every third day which is adequate for a typical installation. iWave-R does not create black walls as negative-only ionizer products will do.
  • Patent pending self-cleaning design ensures ongoing peak performance
  • Needle point ionization actively treats air in the living space
  • Easily installs in minutes in A/C system
  • Universal mounting with magnets
  • Flexible design with no replacement parts
  • Kills mold bacteria and viruses
  • Reduces allergens, odors, smoke, static electricity and other airborne particles
  • Reduces ventilation requirements
  • Keeps coil cleaner
  • Programmable cleaning cycle
  • Alarm contact option for secondary notification
  • Duct systems upto 6 tons (2400 cfm)
  • 3 years warranty
Item#:
4900-20
Manufacturer Item:
4900-20
Manufacturer:
NU-CALGON
This compound is formulated and manufactured for use in many sealing, insulating, and general maintenance applications. It has excellent adhesion capability and is non-staining, non-hardening, and unaffected by wide variations in temperature. Thumb-Tite is packaged in 2 lb. boxes, each box contains two one pound bars.
  • Hot or cold applications
  • Flexible at -20 deg F and non-sagging up to 350 deg F
  • Self adhesive and easy to apply
  • Non-staining and non-hardening
  • Water and vapor proof with no odor
  • Non-corrosive to metals
  • Seal duct work and other HVACR jobs
  • Plug holes, cracks and small voids
  • (2) 1 lb bars
Sid Harvey Item #:J15-2: Replaces Part #:'s : 22547
Item#:
J15-2
Manufacturer Item:
4216-92
Manufacturer:
NU-CALGON
Evap Foam "no rinse" is a high performance, heavy duty detergent, specifically formulated with special surfactants and alkaline cleaners that have been developed into a foaming, no-rinse product. The aerosol product can be sprayed either right side up or upside down, and is ideal for use on most coils, but particularly suited for cooling or evaporator coils.
  • Cleans and deodorizes
  • Easily sprayed from any angle right side up or upside down
  • Self-rinsing, fast breaking foam
  • Biodegradable
  • Can be used with talon aerosol wand (4776-0)
Sid Harvey Item #:4171-75: Replaces Part #:'s : 4743
Item#:
4171-75
Manufacturer Item:
4171-75
Manufacturer:
NU-CALGON
Rx11-flush is a unique solvent that has been engineered for flushing refrigeration and air conditioning systems. Its patented HFC based solvent formulation is powerful enough to flush away sludge, carbon residue, oils, acids, water and other particulate. This makes it ideal for system flushing after burnouts, retrofits and for flushing line sets for R-410A conversions. It is non-toxic, non-flammable and is non-ozone depleting. From time to time, refrigeration and air conditioning systems suffer failures which result in contamination. The most common such failure is a compressor burnout. During such an event, the refrigeration system becomes contaminated with large quantities of unwanted particulate, sludge, acids, carbon residues and possibly moisture. All of these contaminants must be removed before the system can be returned to duty.
  • Safer, non-toxic and non-flammable
  • Used the same way as R-11
  • Can be used for new system cleaning, retrofits, and flushing line sets or after burnouts
  • All packages are pressurized for easy application
  • Flushes 3-4 tons
Sid Harvey Item #:4300-09: Replaces Part #:'s : 32814
Item#:
4300-09
Manufacturer Item:
43003
Manufacturer:
NU-CALGON
All viscosities are manufactured by Calumet Lubricant Co. and are approved by Copeland, Trane and other compressor manufacturers, approvals varying by viscosity. They are specifically designed for today's high performance air conditioning and refrigeration compressors. These modern compressors run at higher speeds and generate higher temperatures and they need better lubrication. Use of C-3s, C-4s, and C-5s mineral oil will insure continued efficient system operation, providing the important properties required from a good refrigeration oil. Nu-Calgon mineral oils combine excellent solubility and stability with good floc and pour points to provide excellent low temperature performance.
  • Recommended by OEM's for use with CFC's and HCFC's
  • Approved by OEM's including Copeland, Carlyle, etc.
  • C-3s is approved replacement for 3GS
Sid Harvey Item #:4303-07: Replaces Part #:'s : F49
Item#:
4303-07
Manufacturer Item:
4303-07
Manufacturer:
NU-CALGON
Nu-Foam is an expanding, polyurethane, prepolymer foam that is used as a sealant and an insulating product. It is designed to seal, fill and insulate small cracks, gaps and voids. Tack free time for Nu-Foam is less than 3 minutes at 7 deg F and 4-5% relative humidity. Its R-Value is 4.9 per" thick making a very good insulator in most any application and can even provide sound-deadening. Nu-Foam is UL classified and is fire retardant. Can withstand temperatures up to 24 deg F. It can be used to seal and insulate areas such as openings created for refrigeration, air conditioning and heating tubes or pipes, duct joints, utility penetrations in exterior sheeting, masonry, concrete or wood walls, and other areas where unwanted air penetration might occur.
  • Yields 352 linear feet (medium can) and 78 linear feet (large can) of 3/8" bead
  • Tack-free in 3 min and dries in 4 hr
  • Insulates against heat loss and heat gain
  • Fire retardant
  • Two years shelf life
  • No CFC's, no HCFC's
Item#:
4293-75
Manufacturer Item:
4293-75
Manufacturer:
NU-CALGON
Nu-Calgon Vacuum Pump Oil is a quality blend of high-grade lubricants, providing for oil that performs at the deepest vacuum. It lubricates to minimize wear and provide surface protection, and its high viscosity index assures adequate lubrication at high and low pressures. In addition, its broad package line guarantees the right package size for all levels of service activity, from the service professional handling only an occasional evacuation to the one conducting several every day.
  • A multi-viscosity oil as specified by its viscosity index of 100
  • Multi-viscosity oils provide for peak performance at wide temperature and pressures
  • Lubricates and seals at operating temperatures developed by pump
  • Very low vapor pressure
  • A critical characteristic of a vacuum pump oil
  • Pop-up caps on pints and quarts for complete ease of pouring into pump's oil port
  • Use of a quality vacuum pump oil is recognized as one of the more important elements in maintaining the pump's designed performance day to day
Item#:
4383-07
Manufacturer Item:
4383-07
Manufacturer:
NU-CALGON
For spraying coil cleaners such as Nu-Brite, CalClean, HD CalClean, Alka-Brite Plus, Tri-Pow'r HD or any of the other quality Nu-Calgon coil cleaners for cleaning air cooled condensers, evaporator coils, etc. No pre-mixing is necessary as chemical and water are automatically blended in mixing head as you spray. Use for coil cleaning as well as in food preparation areas, wash rooms, or any situation where use of water-diluted chemicals are required.
  • The coil gun probe provides easy access for inside out cleaning of coils
  • Recommended water pressure 40 - 60 psi
  • Quick-disconnect feature
  • Foam wand to enhance foaming
  • Deflector tip to fan out spray
  • Connects to optional coil gun probe accessory (4774-1) for 90 deg direction of spray inside the coil
Sid Harvey Item #:4774-0: Replaces Part #:'s : 4814
Item#:
4774-0
Manufacturer Item:
4774-0
Manufacturer:
NU-CALGON
Nickel-Safe ice machine cleaner is a specially formulated citric/phosphoric food-grade product for removing scale deposits from ice makers having nickel-plated or tin-plated evaporators. It is acceptable for use in machines made by Manitowoc and other manufacturers using nickel. In fact, it was the industry's first nickel-safe product, introduced in collaboration with Manitowoc. Usage rate should be in accordance with the manufacturers instructions or 16 fl oz with 3 gal of system water. The number one category of problems troubling an ice machine are water-related and the most frequently is lime scale. As the water is frozen into ice during an ice maker's cycle, the naturally occurring dissolved minerals in the water, some of which can combine to form lime scale, remain behind in the unfrozen recirculating ice water simply because water tries to freeze in its pure state. As the cycle continues and more water is made into ice, the minerals over concentrate and eventually precipitate as a lime scale deposit. As the scale begins to form, it creates a physical obstruction that results in: plugged distribution holes, restricted water flow and eventually the ice maker will hang-up or jam. Ice harvest is reduced and eventually the machine will shut down, requiring service. This sequence of events can affect both cubers and flakers. Some believe that flakers are free of scale problems since all of the water is made into ice. Not true. Flakers can scale-up as well, jamming the auger and eventually resulting in a broken belt or drive mechanism.
  • Nickel-safe ice machine cleaner is a specially formulated food-grade product
  • Complete family of liquid ice machine cleaners
  • Formulated for use in all makes and models of ice makers including those with nickel and tin plated evaporators
  • Functional in cubers, flakers, drum and tube machines
Sid Harvey Item #:4287-34: Replaces Part #:'s : F1-43A
Item#:
4287-34
Manufacturer Item:
4287-34
Manufacturer:
NU-CALGON
Foam-Tite insulation tape provides the service technician with a quality yet economical solution to one of the most common HVACR application problems, sweating or condensation on air conditioning, refrigeration, chilled water or other cold lines. Because of its excellent insulation properties, it can also be used on hot water lines for insulation against heat loss. Keeps cold lines cold and hot lines hot. It can be overlapped or the edges can be butted. The amount of tape that will be required and the style of wrap (over-lapped, butted or both) will depend upon relative humidity, ambient temperature and the temperature of the pipe to be covered.
  • Closed cell construction foam tape
  • Stops sweating and condensation on refrigeration or other cold lines
  • Insulates against heat loss
  • Self-adhesive and easy to apply
Sid Harvey Item #:J6-4: Replaces Part #:'s : 6006
Item#:
J6-4
Manufacturer Item:
4219-12
Manufacturer:
NU-CALGON
|◀ 1 - 12 of 170 ▶|
View: