Home  > DANFOSS MANUFACTURING CO LTD(x)
View:
Danfoss 013G8250 Non-Electric Operator,

Danfoss 013G8250

,

013G8250

Item#:
013G8250
Manufacturer Item:
013G-8250
Manufacturer:
DANFOSS MANUFACTURING CO LTD
Flow Rate
  • Atomizing nozzles are available in a wide range of flow rates, all but eliminating the need for specially calibrated nozzles. Between 1.00 GPH and 2.00 GPH, for example, seven different flow rates are available. Generally, with hot water and warm air heat, the smallest firing rate that will adequately heat the house on the coldest day is the proper size to use and the most economical. Short on-cycles result in low efficiency. Another guideline is to select the flow rate that provides a reasonable stack temperature regardless of the connected load. (According to the New England Fuel Institute, aim for a stack temperature of 400°F or lower on matched packaged units or 500°F or lower on conversion burners.) If the boiler or furnace is undersized for the load, it may be necessary to fire for the load and ignore the efficiency
    Spray Angle
  • Spray angles are available from 30° through 90° in most nozzle sizes to meet the requirements of a wide variety of burner air patterns and combustion chambers. Usually it is desirable to fit the spray angle to the air pattern of the burner. In todays flame retention burner, it is possible to fire more than one spray angle with good results. Generally, round or square combustion chambers should be fired with 70° to 90° nozzles. Long, narrow chambers usually require 30° to 60° spray angles.
  • Burner Air Patterns
  • Burner air patterns are much like nozzle spray patterns in that they fall into the same general classifications, either hollow or solid. As you would expect, a burner with a hollow air pattern generally requires a hollow cone fuel nozzle. A burner with a solid air pattern will give highest efficiency with a solid cone nozzle, but the flame will probably be longer.
  • Item#:
    030G6440
    Manufacturer Item:
    030G6440
    Manufacturer:
    DANFOSS MANUFACTURING CO LTD
    Item#:
    060G1037
    Danfoss HCZC0150UWF300N Refrigeration Condensing Unit 1-1/5 HP 230/1 Medium/High Temperature,

    HCZC0150UWF300N

    ,

    HCZC0150UWF300N

    Item#:
    HCZC0150UWF300N
    Manufacturer Item:
    114N6401
    Manufacturer:
    DANFOSS MANUFACTURING CO LTD
    Danfoss 013G8562 Remote Sensor Wall Mount (Non-Electrical) 6' Cap,

    Danfoss 013G8562

    ,

    013G8562

    Item#:
    013G8562
    Manufacturer Item:
    013G-8562
    Manufacturer:
    DANFOSS MANUFACTURING CO LTD
    Item#:
    117U5023
    Danfoss 013G8024 Nickel-Plated Brass Thermostatic Radiator Angle Valve, 1", FPT x MPT Union Tailpiece
    • Thermostatic radiator valves regulate the flow of hot water or low pressure steam through free-standing radiators, baseboards or convectors in hot water and 2-pipe steam systems
    • Valves are fitted with a packing gland assembly that is replaceable while the system is in operation
    • EPDM rubber valve disc provides a seal against the valve seat at differential pressures of up to 15 psig in hot water heating systems, while 15 psig for low pressure steam systems
    • Manual plastic cap supplied to protect the valve pusHPin and provide manual control of the valve during installation
    • Valves remain normally open with no operator mounted
    • Brass bonnet, spindle, nickel-plated tailpiece, union nut, EPDM disc, packing O-ring, stainless steel spring
    Sid Harvey Item #:013G8024: Replaces Part #:'s : 5841
    ,

    013G8024

    ,

    013G8024

    Item#:
    013G8024
    Manufacturer Item:
    013G8024
    Manufacturer:
    DANFOSS MANUFACTURING CO LTD
    Danfoss 013G8020 Thermostatic Radiator Straight 3/4" Nickel-Plated Brass,

    Danfoss 013G8020

    ,

    013G8020

    Item#:
    013G8020
    Manufacturer Item:
    013G-8020
    Manufacturer:
    DANFOSS MANUFACTURING CO LTD
    View: