Thermo Dynamics Boilers S100 High Altitude Hydronic Oil Fired Water Boiler with AFG Burner, 140K BTU 84.2% AFUE, With Beckett Burner

• Allows the installer to size the boiler more closely to the home heating needs for greater efficiency, the lowest firing rate, 0.85 - 87,000 BTU, is necessary for many well insulated homes where the heat loss is minimal
• 1" thick pyrolite ceramic fiber combustion chamber, fast warm-up - glows to incandescence in 11 - 17 sec, large diameter allows brushing flue passages without punching through chamber
• S-series operates at 140 psi pump pressure for better fuel atomization, thereby having the ability to tolerate fuel oil with heavy ends
• S-series is standard with a state-of-the-art, solid state ignition system, making it more tolerant to low VAC age or VAC age fluctuations
• Integrated ignition
• Electronic delay with solenoid valve clean-cut fuel pump
• S-series has exceptional water content, the first size has 16 Gallon of water, high water volume and placement of the coil in the hottest part of the boiler allows for maximum coil performance
• The unique tube design of the S-series boiler heat exchanger slows the flue gases, allowing for more effective heat transfer without the need for extreme baffling often seen in other vertical tube boilers
• Each boiler is constructed and hydrostatically tested in accordance with ASME boiler code, the capacity and efficiency are rated in accordance with the standards of the institute of boiler and radiator manufacturers (IBR)
• Built-in air scoop purges air from the system providing a quiet, trouble free hot water heating system without the use of external devices
• Extended flange coil is away from the boiler for easy accessibility, use of ribbed neck carriage bolts eliminates the problems encountered when a weld stud is broken during servicing, large coil plate allows for a greater gasket sealing area
• Extended weld fittings of SA106-schedule 80 seamless pipe extend beyond the jacket and allow the service technician or homeowner to see small leaks that, if undetected, could later damage the boiler shell and void the warranty
• Easy cleaning and maintenance accessibility to combustion areas and the open tubes make it easy for the service technician to thoroughly clean the boiler
• Flush jacket, altitude, temperature and pressure gauge, ASME relief valve, thankless heater - 3 gpm, factory assembled, wired and packaged, 3450 RPM high-speed flame retention oil burner, interrupted primary ignition, hydronic triple aquastat relay, 007 circulator pump, brass boiler drain valve

Thermo Dynamics Boilers HT-90/110 Steel 3-Pass Oil Fired Water Boiler 126K BTU Input, 95K BTU Output, 85.1 AFUE, With Beckett Burner

• A wet-base design, a horizontal tube and a 3-pass heat exchanger make this one of the most efficient boiler designs available
• A 5 gpm tankless coil with a 30 Gallon boiler water content assures abundant hot water
• Forced draft burner eliminates chimney draft problems
• Multiple firing rates on the same unit
• 1-piece boiler construction ensures years of trouble-free service and there are no push nipples or"O" rings to leak
• Heat exchanger easily accessible for cleaning
• The 85% AFUE rating is among the highest department of energy (DOE) ratings
• Due to the horizontal tube and wet-base, the HT is remarkably quiet, the unit-flow path of combustion gases allows for smoother, quieter combustion than firebox, wet-leg designed boilers
• Each boiler is constructed and hydrostatically tested in accordance with ASME boiler code, the capacity and efficiency are rated in accordance with the standards of the institute of boiler and radiator manufacturers (IBR)
• Limited lifetime warranty
• Built-in air scoop purges air from the system providing a quiet, trouble free hot water heating system without the use of external devices
• Extended flange coil is away from the boiler for easy accessibility, use of ribbed neck carriage bolts eliminates the problems encountered when a weld stud is broken during service, the large coil plate allows for a greater gasket sealing area
• Weld fittings extend beyond the jacket and allow the service technician or homeowner to see small leaks that, if undetected, could later damage the boiler shell and potentially void the warranty
• Easy cleaning and maintenance accessibility to combustion areas and the open tubes make it easy for the service technician to thoroughly clean the boiler
• No tight, pin-type passage ways with hidden nooks and crannies, making a thorough cleaning possible
• A well-maintained boiler continues to perform at higher efficiency and is less likely to develop service problems
• Factory mounted/wired burner and controls
• Fully insulated heat exchanger with powder-coated cabinet
• Equipped with triple aquastat, circulator and temperature/altitude gauge
• (2) 1-1/2" return

Thermo Dynamics Boilers S85 Steel High Altitude Oil Fired Water Package Boiler, 83.3% AFUE, 119K BTU Input, 100K BTU Output, With Beckett Burner

• Allows the installer to size the boiler more closely to the home heating needs for greater efficiency, the lowest firing rate, 0.85 - 87000 BTU, is necessary for many well insulated homes where the heat loss is minimal
• 1" thick pyrolite ceramic fiber combustion chamber, fast warm-up - glows to incandescence in 11 - 17 sec, large diameter allows brushing flue passages without punching through chamber
• S-series operates at 140 psi pump pressure for better fuel atomization, thereby having the ability to tolerate fuel oil with heavy ends
• S-series is standard with a state-of-the-art, solid state ignition system, making it more tolerant to low VAC age or VAC age fluctuations
• Integrated ignition
• Electronic delay with solenoid valve clean-cut fuel pump
• S-series has exceptional water content, the first size has 16 Gallon of water, high water volume and placement of the coil in the hottest part of the boiler allows for maximum coil performance
• The unique tube design of the S-series boiler heat exchanger slows the flue gases, allowing for more effective heat transfer without the need for extreme baffling often seen in other vertical tube boilers
• Each boiler is constructed and hydrostatically tested in accordance with ASME boiler code, the capacity and efficiency are rated in accordance with the standards of the institute of boiler and radiator manufacturers (IBR)
• Built-in air scoop purges air from the system providing a quiet, trouble free hot water heating system without the use of external devices
• Extended flange coil is away from the boiler for easy accessibility, use of ribbed neck carriage bolts eliminates the problems encountered when a weld stud is broken during servicing, large coil plate allows for a greater gasket sealing area
• Extended weld fittings of SA106 Schedule 80 seamless pipe extend beyond the jacket and allow the service technician or homeowner to see small leaks that, if undetected, could later damage the boiler shell and void the warranty
• Easy cleaning and maintenance accessibility to combustion areas and the open tubes make it easy for the service technician to thoroughly clean the boiler
• Flush jacket, altitude, temperature and pressure gauge, ASME relief valve, thankless heater - 3 gpm, factory assembled, wired and packaged, 3450 RPM high-speed flame retention oil burner, interrupted primary ignition, hydronic triple aquastat relay, 007 circulator pump, brass boiler drain valve
• Lifetime limited warranty

Thermo Dynamics Boilers S110 Steel High Altitude Oil-Fired Water Boiler, 154K BTU Input, 129K BTU Output, 83% AFUE, With Beckett Burner

• Allows the installer to size the boiler more closely to the home heating needs for greater efficiency, the lowest firing rate, 0.85 - 87000 BTU, is necessary for many well insulated homes where the heat loss is minimal
• 1" thick pyrolite ceramic fiber combustion chamber, fast warm-up - glows to incandescence in 11 - 17 sec, large diameter allows brushing flue passages without punching through chamber
• S-series operates at 140 psi pump pressure for better fuel atomization, thereby having the ability to tolerate fuel oil with heavy ends
• S-series is standard with a state-of-the-art, solid state ignition system, making it more tolerant to low VAC age or VAC age fluctuations
• Integrated ignition
• Electronic delay with solenoid valve clean-cut fuel pump
• S-series has exceptional water content, the first size has 16 Gallon of water, high water volume and placement of the coil in the hottest part of the boiler allows for maximum coil performance
• The unique tube design of the S-series boiler heat exchanger slows the flue gases, allowing for more effective heat transfer without the need for extreme baffling often seen in other vertical tube boilers
• Each boiler is constructed and hydrostatically tested in accordance with ASME boiler code, the capacity and efficiency are rated in accordance with the standards of the institute of boiler and radiator manufacturers (IBR)
• Built-in air scoop purges air from the system providing a quiet, trouble free hot water heating system without the use of external devices
• Extended flange coil is away from the boiler for easy accessibility, use of ribbed neck carriage bolts eliminates the problems encountered when a weld stud is broken during servicing, large coil plate allows for a greater gasket sealing area
• Extended weld fittings of SA106 Schedule 80 seamless pipe extend beyond the jacket and allow the service technician or homeowner to see small leaks that, if undetected, could later damage the boiler shell and void the warranty
• Easy cleaning and maintenance accessibility to combustion areas and the open tubes make it easy for the service technician to thoroughly clean the boiler
• Flush jacket, altitude, temperature and pressure gauge, ASME relief valve, thankless heater - 3 gpm, factory assembled, wired and packaged, 3450 RPM high-speed flame retention oil burner, interrupted primary ignition, hydronic triple aquastat relay, 007 circulator pump, brass boiler drain valve
• Lifetime limited warranty

Thermo Dynamics Boilers S125/150 Steel High Altitude Oil-Fired Water Boiler, 175K BTU-210K BTU Input, 148K BTU-174K BTU Output, 83 - 84.3% AFUE, With Beckett Burner

• Allows the installer to size the boiler more closely to the home heating needs for greater efficiency, the lowest firing rate, 0.85 - 87000 BTU, is necessary for many well insulated homes where the heat loss is minimal
• 1" thick pyrolite ceramic fiber combustion chamber, fast warm-up - glows to incandescence in 11 - 17 sec, large diameter allows brushing flue passages without punching through chamber
• S-series operates at 140 psi pump pressure for better fuel atomization, thereby having the ability to tolerate fuel oil with heavy ends
• S-series is standard with a state-of-the-art, solid state ignition system, making it more tolerant to low VAC age or VAC age fluctuations
• Integrated ignition
• Electronic delay with solenoid valve clean-cut fuel pump
• S-series has exceptional water content, the first size has 16 Gallon of water, high water volume and placement of the coil in the hottest part of the boiler allows for maximum coil performance
• The unique tube design of the S-series boiler heat exchanger slows the flue gases, allowing for more effective heat transfer without the need for extreme baffling often seen in other vertical tube boilers
• Each boiler is constructed and hydrostatically tested in accordance with ASME boiler code, the capacity and efficiency are rated in accordance with the standards of the institute of boiler and radiator manufacturers (IBR)
• Built-in air scoop purges air from the system providing a quiet, trouble free hot water heating system without the use of external devices
• Extended flange coil is away from the boiler for easy accessibility, use of ribbed neck carriage bolts eliminates the problems encountered when a weld stud is broken during servicing, large coil plate allows for a greater gasket sealing area
• Extended weld fittings of SA106 Schedule 80 seamless pipe extend beyond the jacket and allow the service technician or homeowner to see small leaks that, if undetected, could later damage the boiler shell and void the warranty
• Easy cleaning and maintenance accessibility to combustion areas and the open tubes make it easy for the service technician to thoroughly clean the boiler
• Flush jacket, altitude, temperature and pressure gauge, ASME relief valve, thankless heater - 3 gpm, factory assembled, wired and packaged, 3450 RPM high-speed flame retention oil burner, interrupted primary ignition, hydronic triple aquastat relay, 007 circulator pump, brass boiler drain valve
• Lifetime limited warranty

thermo dynamics boiler s110kd

Thermo Dynamics Boilers LM 75/100 Steel Hydrolic 2-Pass Low Mass Oil Fired Package Boiler, 105-140 MBH Input, 90.3-118.3 MBH Heating, 84 - 85.2% AFUE

• A wet-base design, a horizontal tube and a 2-pass heat exchanger make this one of the best-designed, best-heating boilers on the market
• Swing out burner door
• The low water content provides heat or hot water delivery within minutes of start-up
• Forced draft burner performs with minimal chimney draft
• The compatibility with indirect storage tanks provides enough hot water to meet the comfort requirement of virtually any home
• 1-piece boiler construction ensures years of trouble-free service and there are no push nipples or"O" rings to leak
• There are no push nipples or o-rings to leak
• The compact design saves space, yet it's capable of 3 firing rates
• The low, 5-1/2 Gallon water content provides heat and hot water delivery within minutes of start up, the low mass concept reduces standby losses associated with boilers during off cycles and provides nearly instant heating with less fuel consumption
• 83 - 85% AFUE, the high efficiency obtained with the LM boiler are due to the design to the heat exchanger, a 2-pass, wet base, Scotch Marine design
• 0.75 - 1.1 multiple firing rates- 1-boiler can be fired at 3-different rates, offering versatility and keeping costs low, IBR listed at each firing rate, each unit is supplied with nozzles and labels for all 3-rates
• Standing 36" length x 19" width x 19-3/4" height, this compact boiler not only saves space but can easily be installed in areas not approved for other boilers, the LM series is approved for both closet and alcove installation on combustible flooring
• Each boiler is constructed and hydrostatically tested in accordance with ASME boiler code, the capacity and efficiency are rated in accordance with the standards of the institute of boiler and radiator manufacturers (IBR)
• Lifetime limited warranty
• Built-in air scoop purges air from the system providing a quiet, trouble free hot water heating system without the use of external devices
• Easy cleaning and maintenance accessibility to combustion areas and the open tubes make it easy for the service technician to thoroughly clean the boiler
• The LM-series can be cleaned from either end by simply removing (8) brass nuts and the burner and clean-out door is a hinged, swing-away door

Thermo Dynamics 530247 Tankless Hot Water Coil New Style 5 GPM Round W/Gasket

Thermo Dynamics Boiler OTF-1600 Aluminum Oil Fired Pool Water Package 350K BTU Input, 273K BTU Output
durable, long lasting construction, built to National Board Specifications Comes in Outdoor (OTF) or Indoor (ITF) Versions. All-copper indirect heat exchanger design practically eliminates corrosion, scaling and condensation problems, aluminized flue collector and firebox assembly withstands atmospheric corrosion, flame retention forced draft oil burner provides efficient combustion; easy access for maintenance and adjustment; UL listed components, precast refractory combustion chamber is surrounded by insulating pellets to keep heat loss through the base to a minimum preassembled for ease of installation.

• Flue Pipe 8"
• Firing Rate 2.50
• Width 26-1/4"
• Length 34"
• Height 45"
• Weight 650 Pounds

  thermo dynamics boiler otf-1600

Thermo Dynamics Boilers 337910 Molded Rear Refractory for Models 90/100/110 and 125/135/150 Boilers

• Target wall only

thermo dynamics boiler parts 337910

Thermo-Dynamics HG04N Natural Gas Fired Cast Iron Water Boiler 82% AFUE 95K BTU/hr

Thermo-Dynamics HG04N

Thermo-Dynamics HG03N Natural Gas Fired Cast Iron Water Boiler 82% AFUE 61K BTU/hr

Thermo-Dynamics HG03N