• 1 Heat 24 Vac 35-75 Degrees
  Frost Sentry Garage Thermostat
  This easy-to-operate garage thermostat allows you to maintain temperature to your garage/storage area. Attractive, extra-rugged, highly reliable and accurate, this thermostat will look and perform like new for years to come. Ideal for garages, warehouse, storage facilities, etc
  

  ICM Controls FS1500L

  
  

  ICM Controls FS1500L

ICM318

ICM318

• Intermittent pilot gas ignition control
• Micro-processor-based precision
• Monitors timing, trial for ignition, rollout switch, flame sensing and lockout
• 100% lockout safety feature
• Works with both natural and LP gas systems
• 0.3 amp plus valve load at 24 VAC anticipator setting
• 85 sec trial for ignition
• 0.5 sec flame failure response time
• Remote flame sensing
• Control voltage - line 24 volt (18 - 30 VAC)
• Direct replacement for York 025-27762-700, Johnson Controls G770RJA-1

icm controls icm2901

icm controls icm2901

• Ultra low cost
• Pin-for-pin compatible with OEM type 621 controls
• Simple time and temperature control
• Must have external relays for fan, reversing valve and auxiliary heat
• High installed base

ICM300C

ICM300C

• Fully programmable with LCD diagnostic display
• 25-fault memory storage, non-volatile
• Identifies front and back side faults
• Protects against - VAC age unbalance, high/low VAC age, phase loss, phase reversal, faulty power, incorrect sequencing and rapid short cycling
• Mechanical - surface mount using (2) #8 screws mounting, screw terminals
• -20 to 75 deg C LCD operating temperature
• 0 - 10 min adjustable time delay
• Relay, SPDT output

D10829-499

D10829-499

ICM272C

ICM272C

• Intermittent ignition oil primary control with 45 sec safety timing, replacement for Honeywell R8184G Series
• Controls oil burner, oil valve (if desired) and the ignition transformer in response to a call for heat
• Solid state flame sensing circuit
• LED on terminal strip indicates system lockout
• Enclosed safety switch with external reset butTon
• Mounts on standard 4 x 4" junction box (select models may be mounted directly on burner housing)
• C554A cadmium sulfide flame detector and 24 VAC thermostat required
• Replacement for popular competitive models

icm controls icm1503

icm controls icm1503

• Intermittent ignition oil primary control with 30 sec safety timing, replacement for Honeywell R8184G Series
• Controls oil burner, oil valve (if desired) and the ignition transformer in response to a call for heat
• Solid state flame sensing circuit
• LED on terminal strip indicates system lockout
• Enclosed safety switch with external reset butTon
• Mounts on standard 4 x 4" junction box (select models may be mounted directly on burner housing)
• C554A cadmium sulfide flame detector and 24 VAC thermostat required
• Replacement for popular competitive models

• Controls oil burner, oil valve (if desired) and the ignition transformer in response to a call for heat
• Solid state flame sensing circuit
• LED on terminal strip indicates system lockout
• Enclosed safety switch with external reset butTon
• Mounts on standard 4 x 4" junction box (select models may be mounted directly on burner housing)
• C554A cadmium sulfide flame detector and 24 VAC thermostat required
• Replacement for popular competitive models
• 44.4 amp at 120 VAC/22.2 amp at 240 VAC (contacts - locked rotor)
• Direct replacement for Honeywell R8184G1161/R8184G1294/R8184G4066

icm controls icm1501

icm controls icm1501

icm controls icm271c

icm controls icm271c

ICM Controls ICM282B

ICM Controls ICM282B