Unit Heater Natural Gas Power Vented 100K BTU 83% 120 VAC

Reznor V3 Series Model UDAP gas-fired unit heaters are available in 14 sizes ranging from 30,000 to 400,000 BTUH gas input. All sizes are approved for commercial/industrial installations. Sizes 30-125 carry an additional approval for use in attached residential garage/workshop application. Model UDAP heaters are designed for 82-83% thermal efficiency and are approved for installation in the United States and Canada by the Canadian Standards Association (CSA).

Reznor V3 Series unit heaters have a refreshing new appearance with a glossy white cabinet finish and less visible hardware. Each size cabinet is easily suspended from either 2 or 4 suspension points. Or, an optional hanger kit for Sizes 30-125 allows for ceiling mounting. The low voltage terminal strip on the outside of the cabinet makes connecting control wiring easy with no panels to remove. The addition of a G terminal to the strip, along with the new design of the circuit board, allows for fan only operation (without adding relays). All units have a factory installed gas line nipple to the exterior of the cabinet for easy gas service connection.

The preeminent new internal feature is the Tcore2 heat exchanger and single burner combustion system. Other standard features include a single-stage gas valve, multi-try direct spark ignition with timed lockout, pressure switch to verify vent flow, resiliently isolated venter motor, venter wheel with improved housing, resiliently isolated axial fan and motor assembly, and a high temperature limit control. Sizes 30-125 also include a flame rollout safety switch. Operation is controlled through an integrated circuit board. The circuit board monitors heater operation and has LED diagnostic indicator lights to identify abnormalities in control functions.

The V3 Series unit heaters are designed to provide all the features you expect in a Reznor heater plus improved efficiency, easier installation, and a new look ~ both inside and out. Look for the unique white unit with no visible front and bottom hardware, deep red louvers, black side handle, and angled corner to know you have a genuine Reznor heater.

Sizes 30-400 certified for commercial/industrial heating application

Sizes 30-125 carry an additional approval for use in residential garage/workshop heating applications

82-83% Thermal efficient ~ TOP in its class!

50-60°F Rise range

Tcore2 titanium stabilized aluminized steel heat exchanger

Patented A single burner combustion system including a one-piece burner assembly

115/1/60 Supply voltage

115 Volt open fan motor with internal overload protection

Transformer for 24-volt controls

Integrated circuit board with diagnostic indicator lights

Multi-try direct spark ignition with timed lockout

Fan relay (included on the circuit board)

Single-stage natural gas valve (field adjustable for operation to 9,000 ft. elevation )

Vibration/noise isolated fan and venter motors ~ designed for low noise operation

2-pt and 4-pt Suspension ~ standard on all sizes

External terminal strip for 24-volt wiring

External gas connection

Full fan guard ~ engineered for safety

Improved cabinet design with less visible hardware

Single-stage, propane gas valve (field adjustable for operation to 9,000 ft. elevation B)

Two-stage natural gas or propane gas valve - Sizes 60-400

409 or 316 Stainless steel heat exchangers

Totally enclosed fan motor (Sizes 30-250, 115V only)

Common venting with other gravity vented Category I appliance(s) (Sizes 30-100)

UDX-100

Item#:

UDX-100

Manufacturer Item:

UDX-100

Manufacturer:

REZNOR LLC

UDX-100

Unit Heater Suspended Hydronic 33,000 (High) 23,000 (Low) Copper Tube/Alumimun Fins

Reznor Model WS Steam/Hot Water Suspended Heaters are design-engineered to be technically advanced and esthetically pleasing which makes it the hydronic heater for the 21st century.
This smart new concept in commercial heating units will accommodate all architects who are looking for something new and different.

The heating range of Model WS is 13,000 to 350,000 BTUH. The air volume ranges from 270 to 4,750 CFM.

The heat exchanger is made of one or two rows of steel coils (standard or optional copper coils) with aluminum

The standard steel tubing is very strong and long lasting. Steel tubing is designed for hot water applications up to 150 psi.

The copper tubing used for the heating coil is very thick (0.03, 0.75 mm), making Reznor heating coils extremely sturdy and long lasting. The copper tube diameter is 0.867 (22 mm) O.D. The large tube diameter reduces the water pressure drop, which means these units require lower pump pressure than other hydronic heaters. It also allows a very rapid heat radiation. For steam heating applications copper tube (Option HA12) is required. Designed for high working steam pressure up to 145 psi (10 bar), every heat exchanger is subjected to a pressure test at over 350 psi (25 bar) before leaving the factory.

The heat exchanger assembly receives a special epoxy-polyester powder coating which makes the coil long lasting and increases the thermal output.

The Fan/Motor Assembly is made up of three components: the fan, the motor and the fan guard, which also acts as the main support for the fan. This fan guard is galvanized for protection against corrosion, and is mounted onto the main casing with anti-vibration rubber mountings. The fan guard meets OSHA requirements.*

The standard 2-speed motor is a hermetically sealed motor which is maintenance free. The motor is wired for Data Chart for fan RPM, heating output and CFM ranges. output, or low speed for reduced noise level. All motors have internal protection as a standard feature.

All Model WS units can be installed for either vertical or horizontal discharge.

pre-painted steel helps protect the cabinet against oxidation.

The cabinet is held together by shake-proof screws and molded corner sections to add additional strength and installation.

The optional Air Flow Induction Optimizer is available for horizontally discharged units. The Air Flow Induction the heated air stream. See the optional accessories section for more information.

Units are packaged into strong corrugated cardboard cartons with strengthened upper and lower side sections. These containers are clearly marked with the model number, size and approximate shipping weight.

Units are manufactured in an ISO 9001 registered facility.

WS23/33C

Item#:

WS23/33C

Manufacturer Item:

WS23/33C

Manufacturer:

REZNOR LLC

WS-Series-Broc

WS-Series-Install

WS-Series-Spec

Item#:

195265

Manufacturer Item:

195265

Manufacturer:

REZNOR LLC

	Location Number	Location Description
	0085	WILKES-BARRE DIST CTR (0085) WILKES BARRE PA

S2K Commerce - Products Dropdown

S2K Commerce - Shopping Cart

Current Selected Location - Sid Harvey Garden City (0999) Garden City NY

If you liked to order from a different location, please select from below

S2K Commerce - Order Entry

Unit Heater Natural Gas Power Vented 100K BTU 83% 120 VAC

UDX-100

UDX-100

Unit Heater Suspended Hydronic 33,000 (High) 23,000 (Low) Copper Tube/Alumimun Fins

WS23/33C

WS23/33C

Duct Furnace Suspended 300K BTU Gravity Vented 115 VAC >>LIMITED STOCK CLEARANCE ITEM<<

Duct Furnace Suspended 250K BTU Gravity Vented 120 VAC

X-250

X-250

Duct Furnace Suspended 200K BTU Gravity Vented 120 VAC

X-200

X-200

Chimney Roof Cap 4"

111848

111848

Pilot Assembly

Reznor Heating Parts 110853

Reznor Vertical Match Lit Standing Natural Gas Pilot Assembly Kit for F-25-400 & B-25-400 Unit Heaters

110851

Limit Switch 225 Degrees (Reznor)

196949

Blower Fan Motor 1/2 HP 120 VAC

196247

196247

Fan Motor Assembly Reznor UDAP-75 .06 HP 1550 RPM 120 VAC

196242

196242

DSI Control Board

195265

Save my cart

Only I should see this saved cart

Save my cart

Only I should see this saved cart

Save my cart

Only I should see this saved cart

Save my cart

Only I should see this saved cart