S2K Commerce - Products Dropdown
Actions
S2K Commerce - Shopping Cart
Actions
S2K Commerce - Order Entry
Actions
Armacell J2-33 IMCOA 3/4x1/2 Pipe Insulation 3/4" x 1/2" x 6' Polyethylene Foam
Armacell is a flexible, closed-cell elastomeric tube insulation product used to conserve energy and prevent condensation on piping applications. The product's closed-cell structure creates exceptional thermal properties (k-value of 0.245 at 75 deg F and wvt of 0.03 perm-in) that protect against moisture penetration in applications within a -297 to 220 deg F temperature range. K-Flex Insul-Tube is widely used for its cold weather flexibility, durable skin surface, exacting manufacturing tolerances and lasting performance.
Armacell is a flexible, closed-cell elastomeric tube insulation product used to conserve energy and prevent condensation on piping applications. The product's closed-cell structure creates exceptional thermal properties (k-value of 0.245 at 75 deg F and wvt of 0.03 perm-in) that protect against moisture penetration in applications within a -297 to 220 deg F temperature range. K-Flex Insul-Tube is widely used for its cold weather flexibility, durable skin surface, exacting manufacturing tolerances and lasting performance.
- Insulated tube pipe insulation is an elastomeric material that helps retard heat loss, prevents condensation and provides effective moisture vapor resistance
- Environmentally friendly, CFC free, mould and mildew resistant, fiber free and non-dusting
- Can be used in underground applications above the water table
- Seal before back filling
- Unslit tubing can be slit lengthwise and fit over existing pipes
- <7% linear shrinkage dimensional stability
- <0.01 perm" water vapor permeability,
J2-33 IMCOA 3/4X1/2
,J2-33 IMCOA 3/4X1/2
Item#:
J2-33 IMCOA 3/4X1/2
Manufacturer Item:
IMCOA 3/4X1/2
Manufacturer:
INSULTUBE
The original, Fiber-Free, Flexible Elastomeric Pipe Insulation For Reliable Protection Against Condensation, Mold and Energy Loss. AP Armaflex is the Ideal Insulation Material For Hvac & Refrigeration Systems In Environments Where The Highest Levels Of Condensation Control and Indoor Air Quality Are Required.
Fiber-Free, Formaldehyde-Free, Low Voc and Non-Particulating Formulation Protects Indoor Air Quality
Closed-Cell Structure Provides Excellent Condensation Control
Built-In Vapor Retardant Barrier Eliminates Need For Additional Vapor Retarder
Microban Antimicrobial Product Protection Provides Exceptional Mold Resistance
25/50 Rated For Use In Air Plenums Up To 2" Wall
Item#:
APT05812
Manufacturer Item:
APT05812
Manufacturer:
INSULTUBE
The original, Fiber-Free, Flexible Elastomeric Pipe Insulation For Reliable Protection Against Condensation, Mold and Energy Loss. AP Armaflex is the Ideal Insulation Material For Hvac & Refrigeration Systems In Environments Where The Highest Levels Of Condensation Control and Indoor Air Quality Are Required.
Fiber-Free, Formaldehyde-Free, Low Voc and Non-Particulating Formulation Protects Indoor Air Quality
Closed-Cell Structure Provides Excellent Condensation Control
Built-In Vapor Retardant Barrier Eliminates Need For Additional Vapor Retarder
Microban Antimicrobial Product Protection Provides Exceptional Mold Resistance
25/50 Rated For Use In Air Plenums Up To 2" Wall
Item#:
APT07815
Manufacturer Item:
APT07815
Manufacturer:
INSULTUBE
Armacell BST11812 Pipe Insulation with Lap Seal 1-1/8" x 1/2" x 6' Microban Antimicrobial, Closed-Cell Foam
Armacell BST11812
Item#:
BST11812
Manufacturer Item:
BST11812
Manufacturer:
INSULTUBE
Armacell BST11810 Pipe Insulation with Lap Seal 1-1/8" x 1" x 6' Microban Antimicrobial, Closed-Cell Foam
Polyethylene foam pipe insulation. Its closed cell structure won't wick moisture and helps prevent the absorption of condensation that could cause mold to develop over time. Imcoa SS has an easy to install self seal closure system. Imcoa pipe insulation is semi-slit, and can be completely slit by hand. Imcoa SS is pre-slit with a factory applied pressure sensitive adhesive (PSA) to both seam surfaces and has a release liner for easy installation. All butt joints should be properly sealed. Imcoa and Imcoa SS are easy to cut with a knife and can be fabricated to go around p-traps and fittings.
Polyethylene foam pipe insulation. Its closed cell structure won't wick moisture and helps prevent the absorption of condensation that could cause mold to develop over time. Imcoa SS has an easy to install self seal closure system. Imcoa pipe insulation is semi-slit, and can be completely slit by hand. Imcoa SS is pre-slit with a factory applied pressure sensitive adhesive (PSA) to both seam surfaces and has a release liner for easy installation. All butt joints should be properly sealed. Imcoa and Imcoa SS are easy to cut with a knife and can be fabricated to go around p-traps and fittings.
- CFC/HCFC free
- Non-porous
- Low VOCs
- Halogen free
- Fiber free
- Resistant to mold growth
BST11810
,BST11810
Item#:
BST11810
Manufacturer Item:
BST11810
Manufacturer:
INSULTUBE
Armacell BST11834 Pipe Insulation with Lap Seal 1-1/8" x 3/4" x 6' Microban Antimicrobial, Closed-Cell Foam
Polyethylene foam pipe insulation. Its closed cell structure won't wick moisture and helps prevent the absorption of condensation that could cause mold to develop over time. Imcoa SS has an easy to install self seal closure system. Imcoa pipe insulation is semi-slit, and can be completely slit by hand. Imcoa SS is pre-slit with a factory applied pressure sensitive adhesive (PSA) to both seam surfaces and has a release liner for easy installation. All butt joints should be properly sealed. Imcoa and Imcoa SS are easy to cut with a knife and can be fabricated to go around p-traps and fittings.
Polyethylene foam pipe insulation. Its closed cell structure won't wick moisture and helps prevent the absorption of condensation that could cause mold to develop over time. Imcoa SS has an easy to install self seal closure system. Imcoa pipe insulation is semi-slit, and can be completely slit by hand. Imcoa SS is pre-slit with a factory applied pressure sensitive adhesive (PSA) to both seam surfaces and has a release liner for easy installation. All butt joints should be properly sealed. Imcoa and Imcoa SS are easy to cut with a knife and can be fabricated to go around p-traps and fittings.
- CFC/HCFC free
- Non-porous
- Low VOCs
- Halogen free
- Fiber free
- Resistant to mold growth
BST11834
,BST11834
Item#:
BST11834
Manufacturer Item:
BST11834
Manufacturer:
INSULTUBE
Armacell BST01212 Pipe Insulation with Lap Seal 1/2" x 1/2" x 6' Microban Antimicrobial, Closed-Cell Foam
Armacell BST01212
Item#:
BST01212
Manufacturer Item:
BST01212
Manufacturer:
INSULTUBE
Armacell BST13812 Pipe Insulation with Lap Seal 1-3/8" x 1/2" x 6' Microban Antimicrobial, Closed-Cell Foam
Polyethylene foam pipe insulation. Its closed cell structure won't wick moisture and helps prevent the absorption of condensation that could cause mold to develop over time. Imcoa SS has an easy to install self seal closure system. Imcoa pipe insulation is semi-slit, and can be completely slit by hand. Imcoa SS is pre-slit with a factory applied pressure sensitive adhesive (PSA) to both seam surfaces and has a release liner for easy installation. All butt joints should be properly sealed. Imcoa and Imcoa SS are easy to cut with a knife and can be fabricated to go around p-traps and fittings.
Polyethylene foam pipe insulation. Its closed cell structure won't wick moisture and helps prevent the absorption of condensation that could cause mold to develop over time. Imcoa SS has an easy to install self seal closure system. Imcoa pipe insulation is semi-slit, and can be completely slit by hand. Imcoa SS is pre-slit with a factory applied pressure sensitive adhesive (PSA) to both seam surfaces and has a release liner for easy installation. All butt joints should be properly sealed. Imcoa and Imcoa SS are easy to cut with a knife and can be fabricated to go around p-traps and fittings.
- CFC/HCFC free
- Non-porous
- Low VOCs
- Halogen free
- Fiber free
- Resistant to mold growth
BST13812
,BST13812
Item#:
BST13812
Manufacturer Item:
BST13812
Manufacturer:
INSULTUBE
Armacell BST15812 Pipe Insulation with Lap Seal 1-5/8" x 1/2" x 6' Microban Antimicrobial, Closed-Cell Foam
Polyethylene foam pipe insulation. Its closed cell structure won't wick moisture and helps prevent the absorption of condensation that could cause mold to develop over time. Imcoa SS has an easy to install self seal closure system. Imcoa pipe insulation is semi-slit, and can be completely slit by hand. Imcoa SS is pre-slit with a factory applied pressure sensitive adhesive (PSA) to both seam surfaces and has a release liner for easy installation. All butt joints should be properly sealed. Imcoa and Imcoa SS are easy to cut with a knife and can be fabricated to go around p-traps and fittings.
Polyethylene foam pipe insulation. Its closed cell structure won't wick moisture and helps prevent the absorption of condensation that could cause mold to develop over time. Imcoa SS has an easy to install self seal closure system. Imcoa pipe insulation is semi-slit, and can be completely slit by hand. Imcoa SS is pre-slit with a factory applied pressure sensitive adhesive (PSA) to both seam surfaces and has a release liner for easy installation. All butt joints should be properly sealed. Imcoa and Imcoa SS are easy to cut with a knife and can be fabricated to go around p-traps and fittings.
- CFC/HCFC free
- Non-porous
- Low VOCs
- Halogen free
- Fiber free
- Resistant to mold growth
BST15812
,BST15812
Item#:
BST15812
Manufacturer Item:
BST15812
Manufacturer:
INSULTUBE
Armacell BST21812 Pipe Insulation with Lap Seal 2-1/8" x 1/2" x 6' Microban Antimicrobial, Closed-Cell Foam
Polyethylene foam pipe insulation. Its closed cell structure won't wick moisture and helps prevent the absorption of condensation that could cause mold to develop over time. Imcoa SS has an easy to install self seal closure system. Imcoa pipe insulation is semi-slit, and can be completely slit by hand. Imcoa SS is pre-slit with a factory applied pressure sensitive adhesive (PSA) to both seam surfaces and has a release liner for easy installation. All butt joints should be properly sealed. Imcoa and Imcoa SS are easy to cut with a knife and can be fabricated to go around p-traps and fittings.
Polyethylene foam pipe insulation. Its closed cell structure won't wick moisture and helps prevent the absorption of condensation that could cause mold to develop over time. Imcoa SS has an easy to install self seal closure system. Imcoa pipe insulation is semi-slit, and can be completely slit by hand. Imcoa SS is pre-slit with a factory applied pressure sensitive adhesive (PSA) to both seam surfaces and has a release liner for easy installation. All butt joints should be properly sealed. Imcoa and Imcoa SS are easy to cut with a knife and can be fabricated to go around p-traps and fittings.
- CFC/HCFC free
- Non-porous
- Low VOCs
- Halogen free
- Fiber free
- Resistant to mold growth
BST21812
,BST21812
Item#:
BST21812
Manufacturer Item:
BST21812
Manufacturer:
INSULTUBE
Armacell BST21810 Pipe Insulation with Lap Seal 2-1/8" x 1" x 6' Microban Antimicrobial, Closed-Cell Foam
Polyethylene foam pipe insulation. Its closed cell structure won't wick moisture and helps prevent the absorption of condensation that could cause mold to develop over time. Imcoa SS has an easy to install self seal closure system. Imcoa pipe insulation is semi-slit, and can be completely slit by hand. Imcoa SS is pre-slit with a factory applied pressure sensitive adhesive (PSA) to both seam surfaces and has a release liner for easy installation. All butt joints should be properly sealed. Imcoa and Imcoa SS are easy to cut with a knife and can be fabricated to go around p-traps and fittings.
Polyethylene foam pipe insulation. Its closed cell structure won't wick moisture and helps prevent the absorption of condensation that could cause mold to develop over time. Imcoa SS has an easy to install self seal closure system. Imcoa pipe insulation is semi-slit, and can be completely slit by hand. Imcoa SS is pre-slit with a factory applied pressure sensitive adhesive (PSA) to both seam surfaces and has a release liner for easy installation. All butt joints should be properly sealed. Imcoa and Imcoa SS are easy to cut with a knife and can be fabricated to go around p-traps and fittings.
- CFC/HCFC free
- Non-porous
- Low VOCs
- Halogen free
- Fiber free
- Resistant to mold growth
BST21810
,BST21810
Item#:
BST21810
Manufacturer Item:
BST21810
Manufacturer:
INSULTUBE
Armacell BST21834 Pipe Insulation with Lap Seal 2-1/8" x 3/4" x 6' Microban Antimicrobial, Closed-Cell Foam
Polyethylene foam pipe insulation. Its closed cell structure won't wick moisture and helps prevent the absorption of condensation that could cause mold to develop over time. Imcoa SS has an easy to install self seal closure system. Imcoa pipe insulation is semi-slit, and can be completely slit by hand. Imcoa SS is pre-slit with a factory applied pressure sensitive adhesive (PSA) to both seam surfaces and has a release liner for easy installation. All butt joints should be properly sealed. Imcoa and Imcoa SS are easy to cut with a knife and can be fabricated to go around p-traps and fittings.
Polyethylene foam pipe insulation. Its closed cell structure won't wick moisture and helps prevent the absorption of condensation that could cause mold to develop over time. Imcoa SS has an easy to install self seal closure system. Imcoa pipe insulation is semi-slit, and can be completely slit by hand. Imcoa SS is pre-slit with a factory applied pressure sensitive adhesive (PSA) to both seam surfaces and has a release liner for easy installation. All butt joints should be properly sealed. Imcoa and Imcoa SS are easy to cut with a knife and can be fabricated to go around p-traps and fittings.
- CFC/HCFC free
- Non-porous
- Low VOCs
- Halogen free
- Fiber free
- Resistant to mold growth
BST21834
,BST21834
Item#:
BST21834
Manufacturer Item:
BST21834
Manufacturer:
INSULTUBE