Features

Easily applied in upflow, horizontal left or horizontal right, or downflow installation with minimal conversion necessary.

Venting kit for downflow (counter-flow) applications on B, C, and D cabinets where side discharge is not possible.

The unit cabinet is compact and easy to install with an ideal height of 33 in.

Full length fold-up duct connector flanges for application flexibility.

Easy access to controls to connect power and control wiring.

No electrical knockouts to deal with, making installation easier.

24 V, 40 VA control transformer and control provisions supplied for single or multi-stage add on cooling or heat pump heating.

Built-in, high level self diagnostics with fault code displays standard on integrated control module for reliable operation.

Front-facing screws on flame sensor and hot surface ignitor for ease of service.

Front-facing screws on blower assembly for easy access and removal of blower.

Constant torque blower motor for cooling SEER2 enhancement.

Blower-off delay for cooling SEER2 improvement.

Continuous fan options for indoor air quality (IAQ) performance.

Airflow leakage less than 2% of nominal airflow for duct performance testing conditions.

Low unit current requirement for easy replacement application.

Electronic hot surface ignition saves fuel cost with increased dependability and reliability.

100% shut-off main gas valve for extra safety.

Inducer rotates for easy conversion of venting options.

Five-speed direct drive standard ECM blower motor.

Hi-tech tubular aluminized steel primary heat exchanger.

Corrosion resistant stainless steel secondary heat exchanger including rear cover pan and front vestibule panel.

Quiet inducer operation.

Timed on, adjustable off blower capability for maximum comfort.

Blower door safety switch below the blower deck.

Solid removable bottom panel allows easy conversion for bottom return air applications.

External air filters are used for maximum flexibility in meeting customers' IAQ needs.

1/4 turn knobs are provided for easy independent door removal.

Insulated blower compartment for thermal and acoustic performance.

Internal condensate trap design (patent pending) provides condensate management options and is self priming to prevent nuisance problems.

Protection included from air intake, exhaust vent, or condensate blockage. Venting applications may be installed as either two-pipe sealed combustion or single-pipe vent using indoor combustion air.

No special vent termination required.

These condensing furnace models produce <40 ng/J NOx emissions.

Fold-up duct connector flanges for application flexibility.

Patented self-priming internal condensate trap design for easy installation.

York Z9ET080B12SMPS1

Features

Easily applied in upflow, horizontal left or horizontal right, or downflow installation with minimal conversion necessary.

Venting kit for downflow (counter-flow) applications on B, C, and D cabinets where side discharge is not possible.

The unit cabinet is compact and easy to install with an ideal height of 33 in.

Full length fold-up duct connector flanges for application flexibility.

Easy access to controls to connect power and control wiring.

No electrical knockouts to deal with, making installation easier.

24 V, 40 VA control transformer and control provisions supplied for single or multi-stage add on cooling or heat pump heating.

Built-in, high level self diagnostics with fault code displays standard on integrated control module for reliable operation.

Front-facing screws on flame sensor and hot surface ignitor for ease of service.

Front-facing screws on blower assembly for easy access and removal of blower.

Constant torque blower motor for cooling SEER2 enhancement.

Blower-off delay for cooling SEER2 improvement.

Continuous fan options for indoor air quality (IAQ) performance.

Airflow leakage less than 2% of nominal airflow for duct performance testing conditions.

Low unit current requirement for easy replacement application.

Electronic hot surface ignition saves fuel cost with increased dependability and reliability.

100% shut-off main gas valve for extra safety.

Inducer rotates for easy conversion of venting options.

Five-speed direct drive standard ECM blower motor.

Hi-tech tubular aluminized steel primary heat exchanger.

Corrosion resistant stainless steel secondary heat exchanger including rear cover pan and front vestibule panel.

Quiet inducer operation.

Timed on, adjustable off blower capability for maximum comfort.

Blower door safety switch below the blower deck.

Solid removable bottom panel allows easy conversion for bottom return air applications.

External air filters are used for maximum flexibility in meeting customers' IAQ needs.

1/4 turn knobs are provided for easy independent door removal.

Insulated blower compartment for thermal and acoustic performance.

Internal condensate trap design (patent pending) provides condensate management options and is self priming to prevent nuisance problems.

Protection included from air intake, exhaust vent, or condensate blockage. Venting applications may be installed as either two-pipe sealed combustion or single-pipe vent using indoor combustion air.

No special vent termination required.

These condensing furnace models produce <40 ng/J NOx emissions.

Fold-up duct connector flanges for application flexibility.

Patented self-priming internal condensate trap design for easy installation.

York Z9ET060B12SMPS1

Features

Easily applied in upflow, horizontal left or horizontal right, or downflow installation with minimal conversion necessary.

Venting kit for downflow (counter-flow) applications on B, C, and D cabinets where side discharge is not possible.

The unit cabinet is compact and easy to install with an ideal height of 33 in.

Full length fold-up duct connector flanges for application flexibility.

Easy access to controls to connect power and control wiring.

No electrical knockouts to deal with, making installation easier.

24 V, 40 VA control transformer and control provisions supplied for single or multi-stage add on cooling or heat pump heating.

Built-in, high level self diagnostics with fault code displays standard on integrated control module for reliable operation.

Front-facing screws on flame sensor and hot surface ignitor for ease of service.

Front-facing screws on blower assembly for easy access and removal of blower.

Constant torque blower motor for cooling SEER2 enhancement.

Blower-off delay for cooling SEER2 improvement.

Continuous fan options for indoor air quality (IAQ) performance.

Airflow leakage less than 2% of nominal airflow for duct performance testing conditions.

Low unit current requirement for easy replacement application.

Electronic hot surface ignition saves fuel cost with increased dependability and reliability.

100% shut-off main gas valve for extra safety.

Inducer rotates for easy conversion of venting options.

Five-speed direct drive standard ECM blower motor.

Hi-tech tubular aluminized steel primary heat exchanger.

Corrosion resistant stainless steel secondary heat exchanger including rear cover pan and front vestibule panel.

Quiet inducer operation.

Timed on, adjustable off blower capability for maximum comfort.

Blower door safety switch below the blower deck.

Solid removable bottom panel allows easy conversion for bottom return air applications.

External air filters are used for maximum flexibility in meeting customers' IAQ needs.

1/4 turn knobs are provided for easy independent door removal.

Insulated blower compartment for thermal and acoustic performance.

Internal condensate trap design (patent pending) provides condensate management options and is self priming to prevent nuisance problems.

Protection included from air intake, exhaust vent, or condensate blockage. Venting applications may be installed as either two-pipe sealed combustion or single-pipe vent using indoor combustion air.

No special vent termination required.

These condensing furnace models produce <40 ng/J NOx emissions.

Fold-up duct connector flanges for application flexibility.

Patented self-priming internal condensate trap design for easy installation.

York Z9ET040A10SMPS1

Features

Easily applied in upflow, horizontal left or horizontal right, or downflow installation with minimal conversion necessary.

Venting kit for downflow (counter-flow) applications on B, C, and D cabinets where side discharge is not possible.

The unit cabinet is compact and easy to install with an ideal height of 33 in.

Full length fold-up duct connector flanges for application flexibility.

Easy access to controls to connect power and control wiring.

No electrical knockouts to deal with, making installation easier.

24 V, 40 VA control transformer and control provisions supplied for single or multi-stage add on cooling or heat pump heating.

Built-in, high level self diagnostics with fault code displays standard on integrated control module for reliable operation.

Front-facing screws on flame sensor and hot surface ignitor for ease of service.

Front-facing screws on blower assembly for easy access and removal of blower.

Constant torque blower motor for cooling SEER2 enhancement.

Blower-off delay for cooling SEER2 improvement.

Continuous fan options for indoor air quality (IAQ) performance.

Airflow leakage less than 2% of nominal airflow for duct performance testing conditions.

Low unit current requirement for easy replacement application.

Electronic hot surface ignition saves fuel cost with increased dependability and reliability.

100% shut-off main gas valve for extra safety.

Inducer rotates for easy conversion of venting options.

Five-speed direct drive standard ECM blower motor.

Hi-tech tubular aluminized steel primary heat exchanger.

Corrosion resistant stainless steel secondary heat exchanger including rear cover pan and front vestibule panel.

Quiet inducer operation.

Timed on, adjustable off blower capability for maximum comfort.

Blower door safety switch below the blower deck.

Solid removable bottom panel allows easy conversion for bottom return air applications.

External air filters are used for maximum flexibility in meeting customers' IAQ needs.

1/4 turn knobs are provided for easy independent door removal.

Insulated blower compartment for thermal and acoustic performance.

Internal condensate trap design (patent pending) provides condensate management options and is self priming to prevent nuisance problems.

Protection included from air intake, exhaust vent, or condensate blockage. Venting applications may be installed as either two-pipe sealed combustion or single-pipe vent using indoor combustion air.

No special vent termination required.

These condensing furnace models produce <40 ng/J NOx emissions.

Fold-up duct connector flanges for application flexibility.

Patented self-priming internal condensate trap design for easy installation.

York Z9ET080C16SMPS1

Fujitsu FF70173TS92M Gas Furnace 70K BTU 92% AFUE Constant Torque Motor Upflow/Horizontal"Not Downflow" 17",
,

Fujitsu FF70173TS92M

Fujitsu FF70173TT96M Gas Furnace 95K BTU 96% AFUE Constant Torque Motor Upflow/Horizontal"Not Downflow" 17",
,

Fujitsu FF70173TT96M

Fujitsu FF75174CS80M Gas Furnace 75K BTU 80% AFUE Constant Torque Motor Upflow/Horizontal 17",
,

Fujitsu FF75174CS80M

The Thermo Pride story - located right here in the United States, Thermo Products, makers of Thermo Pride heating and cooling equipment, is known for superior workmanship and product innovation. Thermo Products is committed to producing handcrafted products that provide your family with reliability, comfort, durability, quiet operation and high efficiency. You will have the peace-of-mind that comes from knowing your gas Thermo Pride mobile home furnace is anything but a mass-produced, low-cost compromise between quality and price. Reliability - whether you are upgrading to save energy or your current furnace has failed, you will want to replace it with one that is both dependable and economical. Thermo Pride mobile home furnaces are designed and built specifically as replacement furnaces, so you can easily upgrade the heating or cooling system in your home.

• Integrated coil cabinet for easy air conditioning installation
• Aluminized steel primary heat exchanger
• Stainless steel secondary heat exchanger
• Silicon nitride igniter for quiet and consistent light-off
• 2-piece top design for easy access to vent pipes
• Concentric vent kit available using existing roof jack and standard base
• PVC venting
• Lifetime heat exchanger warranty and 10 years parts warranty

  Thermo Pride CMC2-50DV3N

The Thermo Pride story - located right here in the United States, Thermo Products, makers of Thermo Pride heating and cooling equipment, is known for superior workmanship and product innovation. Thermo Products is committed to producing handcrafted products that provide your family with reliability, comfort, durability, quiet operation and high efficiency. You will have the peace-of-mind that comes from knowing your gas Thermo Pride mobile home furnace is anything but a mass-produced, low-cost compromise between quality and price. Reliability - whether you are upgrading to save energy or your current furnace has failed, you will want to replace it with one that is both dependable and economical. Thermo Pride mobile home furnaces are designed and built specifically as replacement furnaces, so you can easily upgrade the heating or cooling system in your home.

• Integrated coil cabinet for easy air conditioning installation
• Aluminized steel primary heat exchanger
• Stainless steel secondary heat exchanger
• Silicon nitride igniter for quiet and consistent light-off
• 2-piece top design for easy access to vent pipes
• Concentric vent kit available using existing roof jack and standard base
• PVC venting
• Lifetime heat exchanger warranty and 10 years parts warranty

  Thermo Pride CMC2-75DV3N

Unique Manufactured Housing Design with a robust, 19 7/8"W, fully-insulated cabinet to fit the standard MH footprint. The MG2R is our flagship high-efficiency, HUD-compliant, gas furnace. AC-Ready 4-Ton ECM Blower with 5-speed taps, with/without a factory-installed 20"H coil box; allowing for a field-installed 20"/26"H coil box to suit your capacity and access needs. Refer to Split System sell sheets for AHRI-rated coil-fit matches. Quick LP Conversion with an easy-access gas valve regulator and manifold, using the factory-provided LP orifices included in the unit-literature kit. Category IV Venting Approval allows for vertical or horizontal direct venting using an approved non-metallic two-pipe system, or a concentric termination kit for application flexibility. Dependable Warranty and Support, handled directly by Style Crests dedicated HVAC Team, offering the most competitive warranty coverage and service in the Manufactured Housing Industry.

Nortek Global (Intertherm) MG2S060F2ABM2