Current Selected Location - Sid Harvey Garden City (0999) Garden City NY

Armstrong Air Conditioning Parts 13H3601 Condenser Fan Motor 1/4 HP 230 VAC 850 RPM (Lennox)

All products are designed and manufactured for use within forced air systems, providing effective distribution of conditioned air from the air handler to every room of a residence.Metal duct and fittings are constructed from hot-dipped Galvanized steel. All metal products are made true to gauge. Sheet metal duct, pipe, and fittings are designed with industry and regional standards in mind, as well as ACCA and SMACNA recommendations and requirements. Products are hand-crafted to reduce noise and friction and constructed to maximize efficiency by increasing airflow without leaks. The quality of our Galvanized steel allows us to create fittings that are rust-resistant and durable

Flow Rate

Atomizing nozzles are available in a wide range of flow rates, all but eliminating the need for specially calibrated nozzles. Between 1.00 GPH and 2.00 GPH, for example, seven different flow rates are available. Generally, with hot water and warm air heat, the smallest firing rate that will adequately heat the house on the coldest day is the proper size to use and the most economical. Short on-cycles result in low efficiency. Another guideline is to select the flow rate that provides a reasonable stack temperature regardless of the connected load. (According to the New England Fuel Institute, aim for a stack temperature of 400°F or lower on matched packaged units or 500°F or lower on conversion burners.) If the boiler or furnace is undersized for the load, it may be necessary to fire for the load and ignore the efficiency
Spray Angle

Spray angles are available from 30° through 90° in most nozzle sizes to meet the requirements of a wide variety of burner air patterns and combustion chambers. Usually it is desirable to fit the spray angle to the air pattern of the burner. In todays flame retention burner, it is possible to fire more than one spray angle with good results. Generally, round or square combustion chambers should be fired with 70° to 90° nozzles. Long, narrow chambers usually require 30° to 60° spray angles.

Burner Air Patterns

Burner air patterns are much like nozzle spray patterns in that they fall into the same general classifications, either hollow or solid. As you would expect, a burner with a hollow air pattern generally requires a hollow cone fuel nozzle. A burner with a solid air pattern will give highest efficiency with a solid cone nozzle, but the flame will probably be longer.

How often do I need to change my air filter?

There are many factors that can determine when an air filter should be changed. How often the HVAC unit runs, air quality, humidity and other factors can vary greatly from application to application. For most 1, 2 and 4 deep panel or pleated style filters, it is usually recommended to change the filter every 2-3 months. In many commercial and industrial applications static pressure can be monitored and the filters can be changed when they reach their recommended final resistance in inches of water gauge.

What is MERV?

MERV stands for: Minimum Efficiency Reporting Value. MERV is part of the ASHRAE 52.2 Test Standard that determines the ability of an air filter to remove particles of a specific size from an air stream. Air filters can have a MERV of 1 to 16; the higher the MERV, the more efficient the filter is at capturing particles

Russell manufactures a complete line of commercial refrigeration equipment and Solutionsenergy-efficient unit coolers, condensing units, condensers, air handlers, coils and packaged systemsto match any refrigeration requirement. Part of the Rheem family of brands.Russell RL6A094ADAAL Evaporator Walk-In 9K BTU PSC 115 VAC ECM TxV/LLS/T-STAT,
,

Gray Metal Products, Inc., is a family owned business started in 1906, is a full line manufacturer of heating and air conditioning products. For several decades, Gray Metal Products line has been sold to the wholesale distributors and wholesale hardware chains. Our product lines consist of prefabricated air duct and fittings for HVAC, black stovepipe and fittings, as well as hearth accessories and insulated flexible air duct products.

Roth 2342223037 PEX-C Tubing Red Polyethylene 3/4" x 20',
,

Heatcraft Motors 25316201 Interlink 3-Ph ECM Motor 1/2 Hp 208/230 Volt 540 Rpm,

Modine Inducer Motor 3H37362-1 Draft Inducer 120 VAC (Modine)

Bergquist 3259-50-1013-66 Con-Stab Plastic Tee 3/4" CTS

All products are designed and manufactured for use within forced air systems, providing effective distribution of conditioned air from the air handler to every room of a residence.Metal duct and fittings are constructed from hot-dipped Galvanized steel. All metal products are made true to gauge. Sheet metal duct, pipe, and fittings are designed with industry and regional standards in mind, as well as ACCA and SMACNA recommendations and requirements. Products are hand-crafted to reduce noise and friction and constructed to maximize efficiency by increasing airflow without leaks. The quality of our Galvanized steel allows us to create fittings that are rust-resistant and durable.

Weil-McLain Heating Parts 321711145 Section Assembly EGH-125