Bell & Gossett Red Fox 103417 3-Speed In-Line Circulator Pump, 1/15 HP, 115 volt, 2950 RPM, 24 gpm

• Double sintered carbon bearing
• Ceramic shaft
• High starting torque provides years of trouble-free start-ups
• Unique B&G DuraGlide bearing system assures whisper - quiet, maintenance-free operation
• Closed impeller design improves operating efficiency
• Wet rotor circulator
• Stabilized, heat resistant, non-metallic impeller, its closed design improves operating efficiency
• Self-cleaning particle shield protects the shaft and bearings from system start-up debris

Sid Harvey Item #:NRF-25: Replaces Part #:'s : 38573,
,

Bell & Gossett NRF-25

Bell & Gossett NRF-25

Resideo PC3F1558IUF00 Circulator Pump 3-Speed Universal Flange 115 VAC 19' Head Max,

PC3F1558IUF00

PC3F1558IUF00

Resideo PA404A is a pressure actuated high limit, safety control for steam heating boilers. It breaks an electrical circuit to shut down the burner if steam pressure rises above a safe level.

The PA404B is used with suspension-type unit heaters to make the fan circuit when a pressure rise indicates the presence of steam.

Each model contains an SPST MICRO SWITCH snap-acting switch.Sensitive pressure-actuated diaphragm expands or contracts with pressure variations, moving a lever mechanism which operates the snap switch.

A screw on top of the case allows set point adjustment without removing the cover.Differential is adjusted by means of a dial located inside the case..,
,

PA404A1009

PA404A1009

Flexcon Flex2pro PH5 16 ga Cold Rolled Steel Thermal Expansion Tank, 2.1 Gallon, 3/4" MNPT, 200 psig, 11" H x 8" Diameter

100% butyl diaphragm and plastic liner to separate the system water from the tanks air precharge
• Stainless steel sleeve to prevent corrosion, something no other manufacturer offers
• Top chamber is 100% butyl rubber, lower water chamber is copolymer polypropylene
• High pressure, seam weld, helium, final precharge check testing
• Brass valve with O-Ring seal
• 0.9 Gallon maximum accepted volume
  
  

  Flexcon PH5

Resideo PV100 Supervent Air Eliminator 1" FPT,
,

Honeywell PV100

Honeywell PV100

Resideo PV125 Supervent Air Eliminator 1-1/4" FPT,
,

Honeywell PV125

Honeywell PV125

Resideo PV125S Supervent Air Eliminator 1-1/4" OD,
,

Honeywell PV125S

Honeywell PV125S

Resideo PV100S Supervent Air Eliminator 1" OD,
,

Honeywell PV100S

Honeywell PV100S

Mcdonnell & Miller GuardDog RB-24E Low Water Cut-Off, 24 VAC, 160 psi, Automatic Reset

Brass threads provide a metal-to-metal seal that ensures a leak-free installation
• Integrated wrench flats enable secure installation without damage to the housing
• Compact size, easy to install and wire
• Green LED indicates power on
• Red LED indicating low water condition
• Solid state operation
• 15000 ohm probe sensitivity
  
  

  McDonnell & Miller RB-24

Mcdonnell & Miller GuardDog RB-122-E Low Water Cut-Off, 120 VAC, 160 psi, Automatic Reset

Electronic operation, easy to install and wire
• Red low water indicating LED, green power indicating LED
• Automatic reset and now with test button
• 20000 ohm probe sensitivity
• NEMA 1 enclosure
  
  

  McDonnell & Miller RB-122

All products are designed and manufactured for use within forced air systems, providing effective distribution of conditioned air from the air handler to every room of a residence.Metal duct and fittings are constructed from hot-dipped Galvanized steel. All metal products are made true to gauge. Sheet metal duct, pipe, and fittings are designed with industry and regional standards in mind, as well as ACCA and SMACNA recommendations and requirements. Products are hand-crafted to reduce noise and friction and constructed to maximize efficiency by increasing airflow without leaks. The quality of our Galvanized steel allows us to create fittings that are rust-resistant and durable.

Lukjan Metal Products RP011426060

All products are designed and manufactured for use within forced air systems, providing effective distribution of conditioned air from the air handler to every room of a residence.Metal duct and fittings are constructed from hot-dipped Galvanized steel. All metal products are made true to gauge. Sheet metal duct, pipe, and fittings are designed with industry and regional standards in mind, as well as ACCA and SMACNA recommendations and requirements. Products are hand-crafted to reduce noise and friction and constructed to maximize efficiency by increasing airflow without leaks. The quality of our Galvanized steel allows us to create fittings that are rust-resistant and durable.

Lukjan Metal Products RP011826060