Danfoss offers a complete and Flexible range of solenoid valves for use in refrigeration and A/C systems. EVR solenoid valves are direct or servo-operated solenoid valves for liquid, suction and hot gas lines. They are suitable for all refrigeration, freezing and air conditioning applications and are compatible with fluorinated refrigerants. Versions for high-pressure refrigerants are available by contacting Danfoss. The valves can be delivered as normally open or closed as well as with or without manual operation.
Danfoss 068-2007 T2/TE2 Orifice, Size 04
Nominal capacity R22 - 3.43 tons @40F, R404A - 2.89 tons @40F, R134A - 1.82 tons @40F. ** Replaces 068-2074,
,

Danfoss 068-2006

Danfoss offers a complete and Flexible range of solenoid valves for use in refrigeration and A/C systems. EVR solenoid valves are direct or servo-operated solenoid valves for liquid, suction and hot gas lines. They are suitable for all refrigeration, freezing and air conditioning applications and are compatible with fluorinated refrigerants. Versions for high-pressure refrigerants are available by contacting Danfoss. The valves can be delivered as normally open or closed as well as with or without manual operation.
Danfoss 068-2006 T2/TE2 Orifice, Size 03
Nominal capacity R22 - 2.25 tons @40F, R404A - 1.83 tons @40F, R134A - 1.22 tons @40F.,
,

Danfoss 068-2003

Multi-function micro-processor circuit board with these standard features:

Blower start relay - Eliminates field installed boiler relay, allowing direct wiring from the boiler to the air handler

Blower-on fan delay - (heating mode) - preheats the HW coil for 45 seconds.

Blower-off fan delay - (heating and cooling models) - blower continues to operate for 45 seconds after thermostat is satisfied, for increased efficiency

120V or 24V zone valve control - The micro-pro-cessor powers either 120V or 24V field supplied motorized zone valves

Factory or field installed R-410A TXV (cooling or heat pump operation) (non-bleed type)

Manual Air Vent on hot water coil

Blower door shut-off switch (except 60/61HCXW (PSC))

Slide out hot water coil for easier service

Copper tube heating and cooling coils

Compatible with all major brands of split condensing units and heat pumps

Attractive baked-on powder coated cabinet

Primary and secondary condensate drain connections

Easily accessible 1 filter

Cabinet air leakage is no more the 2% when tested in accordance with ASHRAE 193

24HCXW2V10AVB00AAF

Advance Distributers BCRMA3124-S03 Pre-Painted Galvanized Heavy Gauge Steel Air Handler with PisTon Metering and Slant Coil, 24000 BTU, 2 Ton, 12.5 kw, 120 VAC

• Rifled copper tubing, patented lance fin design
• High efficiency 3-speed motors
• Dynamically balanced blowers for quiet, vibration-free operation
• Drain pans are molded of corrosion proof engineering polymer
• Florator, non-bleed A/C or HP expansion valve available factory installed, expansion valves also available as a kit for field installation (all screw-on connections)
• Filter rack with filter - built into every air handler
• Electric heat available factory installed or in kit form for field installation, plug in connections simplify installation of kits
• Fan time delay available as kit or factory installed
• Easily converted to counterflow with kit
• All coils are individually pressure tested at 450 psi, then pressurized and sealed
• 6" width x 9" diameter wheel
• Constant speed, 3-speed blower motor
• Right hand refrigerant and drain connection
• Slab number (A3)
• 0 and 5 kw, hot water standard stripped wire
• 13-1/2" width x 17" depth supply duct opening
• 10-1/4" width x 17-1/4" depth return duct opening

,

Advance Distributers BCRMA3124-S01

Advance Distributers BCRMA3124-S01 Pre-Painted Galvanized Heavy Gauge Steel Air Handler with PisTon Metering and Slant Coil, 24000 BTU, 2 Ton, 12.5 kw, 208/240 VAC

• Rifled copper tubing, patented lance fin design
• High efficiency 3-speed motors
• Dynamically balanced blowers for quiet, vibration-free operation
• Drain pans are molded of corrosion proof engineering polymer
• Florator, non-bleed A/C or HP expansion valve available factory installed, expansion valves also available as a kit for field installation (all screw-on connections)
• Filter rack with filter - built into every air handler
• Electric heat available factory installed or in kit form for field installation, plug in connections simplify installation of kits
• Fan time delay available as kit or factory installed
• Easily converted to counterflow with kit
• All coils are individually pressure tested at 450 psi, then pressurized and sealed
• 6" width x 9" diameter wheel
• Constant speed, 3-speed blower motor
• Right hand refrigerant and drain connection
• Slab number (A3)
• 0 and 5 kw, hot water standard stripped wire
• 13-1/2" width x 17" depth supply duct opening
• 10-1/4" width x 17-1/4" depth return duct opening

,
,

York CTF30A5ADS1