Current Selected Location - Sid Harvey Garden City (0999) Garden City NY

All products are designed and manufactured for use within forced air systems, providing effective distribution of conditioned air from the air handler to every room of a residence.Metal duct and fittings are constructed from hot-dipped Galvanized steel. All metal products are made true to gauge. Sheet metal duct, pipe, and fittings are designed with industry and regional standards in mind, as well as ACCA and SMACNA recommendations and requirements. Products are hand-crafted to reduce noise and friction and constructed to maximize efficiency by increasing airflow without leaks. The quality of our Galvanized steel allows us to create fittings that are rust-resistant and durable.

Yellow Jacket 69092 Heat Gun Kit, 115 volt, 600 and 1000 deg F

Shock proof and tough housing is durable and lightweight

All Snappy products are designed and manufactured for use within forced air systems, providing effective distribution of conditioned air from the air handler to every room of a residence.Metal duct and fittings are constructed from hot-dipped Galvanized steel. All metal products are made true to gauge. Sheet metal duct, pipe, and fittings are designed with industry and regional standards in mind, as well as ACCA and SMACNA recommendations and requirements. Products are hand-crafted to reduce noise and friction and constructed to maximize efficiency by increasing airflow without leaks. The quality of our Galvanized steel allows us to create fittings that are rust-resistant and durable.

All Snappy products are designed and manufactured for use within forced air systems, providing effective distribution of conditioned air from the air handler to every room of a residence.Metal duct and fittings are constructed from hot-dipped Galvanized steel. All metal products are made true to gauge. Sheet metal duct, pipe, and fittings are designed with industry and regional standards in mind, as well as ACCA and SMACNA recommendations and requirements. Products are hand-crafted to reduce noise and friction and constructed to maximize efficiency by increasing airflow without leaks. The quality of our Galvanized steel allows us to create fittings that are rust-resistant and durable.

All Snappy products are designed and manufactured for use within forced air systems, providing effective distribution of conditioned air from the air handler to every room of a residence.Metal duct and fittings are constructed from hot-dipped Galvanized steel. All metal products are made true to gauge. Sheet metal duct, pipe, and fittings are designed with industry and regional standards in mind, as well as ACCA and SMACNA recommendations and requirements. Products are hand-crafted to reduce noise and friction and constructed to maximize efficiency by increasing airflow without leaks. The quality of our Galvanized steel allows us to create fittings that are rust-resistant and durable.

C & S Manufacturing Basset FHA-100-1816-8 Plain Steel Nail Plate, 18" L x 1-1/2" W, 16 Gauge

C & S Manufacturing Basset FHA-300-1816-8 Plain Steel Nail Plate, 18" L x 3" W, 16 Gauge

Protects wiring and piping during construction
• 8 holes per side
• 2 plates can be used for maximum strength when reinforcing joists
  C&S Manufacturing Corporation was founded over 60 years ago in May of 1962 by John D. Collins who worked many previous years as a Heating Contractor in the family heating business. After obtaining a patent on his unique Basset Bracket the company was dedicated to the manufacturing and selling of time and labor-saving products initially for the HVAC industry.
  As business grew and new labor-saving ideas were developed, the company expanded into the plumbing industry with similar labor saving and code required products. The Basset Product Line of C&S Manufacturing is well known in these industries and is now stocked by over 2,500 Plumbing and HVAC wholesalers throughout the country. Basset Products are known for their quality. C&S Manufacturing is committed to the On Time shipment of products through the wholesale distribution channel to be available to the contractor when needed.,
  

Copeland Parts 998-1000-14 Demand Cooling Kit 120 VAC 4D

Make sure you ask for and use genuine Copleand parts. Copeland parts fit right, first time. Insisting on genuine Copeland parts will keep your refrigeration & A/C Conpressor running reliably for the low haul.

Embraco FF7.5HBK1 Hermetic Refrigeration Compressor

1/5+ HP 120 VAC 1 PH R134A

Flow Rate

• Atomizing nozzles are available in a wide range of flow rates, all but eliminating the need for specially calibrated nozzles. Between 1.00 GPH and 2.00 GPH, for example, seven different flow rates are available. Generally, with hot water and warm air heat, the smallest firing rate that will adequately heat the house on the coldest day is the proper size to use and the most economical. Short on-cycles result in low efficiency. Another guideline is to select the flow rate that provides a reasonable stack temperature regardless of the connected load. (According to the New England Fuel Institute, aim for a stack temperature of 400°F or lower on matched packaged units or 500°F or lower on conversion burners.) If the boiler or furnace is undersized for the load, it may be necessary to fire for the load and ignore the efficiency

Spray Angle

• Spray angles are available from 30° through 90° in most nozzle sizes to meet the requirements of a wide variety of burner air patterns and combustion chambers. Usually it is desirable to fit the spray angle to the air pattern of the burner. In todays flame retention burner, it is possible to fire more than one spray angle with good results. Generally, round or square combustion chambers should be fired with 70° to 90° nozzles. Long, narrow chambers usually require 30° to 60° spray angles.

Burner Air Patterns

• Burner air patterns are much like nozzle spray patterns in that they fall into the same general classifications, either hollow or solid. As you would expect, a burner with a hollow air pattern generally requires a hollow cone fuel nozzle. A burner with a solid air pattern will give highest efficiency with a solid cone nozzle, but the flame will probably be longer

Harris Dynaflow D636S Brazing Alloy, 1/8" Diameter x 36" L, 25 lb, Dynaflow melts and flows at temperatures very close to Stay Silv 15 and provides comparable brazed mechanical properties. This makes Dynaflow an excellent cost effective alternative to the 15% silver alloys. This premium, medium range silver alloy has been meticulously formulated to even tighter specifications than our standard copper-to-copper alloys.,

Multi-position design for horizontal or vertical installation without modification

Two sloped condensate pans on each unit for horizontal or vertical applications

Standard sloped drain pans and cleanable insulation treatedwith Environmental Protection
Agency (EPA) registered antimicrobial agent improves indoor air quality

High-static design meets a wider range of applications thancompetitive packaged air handler lines

Ultra low leak economizer accessory provides ventilation air and free cooling with built in Fault Detection and Diagnostic (FDD) capabilities

Single refrigerant circuit on 072 and 091 sizes. Dual refrigerant circuit on 120-336 sizes

Dual circuit can be field modified for use on single circuit condensers

Cooling coils with mechanically bonded fins provide peak heat transfer

Optional 2-speed indoor fan with VFD controller

Standard factory-installed thermostatic expansion valve (TXV) with removable power element

Easy maintenance - removal of single panel allows access to virtually all components

Die-formed galvanized steel casings provide durability and structural integrity. Optional paint is available

24-volt terminal block for control wiring connection

Hot water coil, steam coil, and electric heat accessories are available