The Ranco ETC Series Electronic Temperature Control offers a full-featured electronic replacement for electrical-mechanical temperature controls used in many commercial refrigeration applications. With its wide temperature range, one and two stage capability, selectable heating/cooling modes and multi-voltage input, the ETC is designed to provide application flexibility.

• LCD read-out for sensor temperature, control settings and relay status
• High amp output relay (FLA 16 amp at 120 VAC and 8 amp at 208/240 VAC) 1-stage
• EE-PROM memory retains control settings during power outages
• Keypad lockout to prevent end-user alteration of settings
• 8 feet lead with sensor is extendable up to 400 feet using 18 or 22 ga thermostat wire
• Easy 4-step set-up
• Heavy-duty relay is 1 HP rated
• Selectable celsius or fahrenheit heating/cooling modes
• White backlight on display
• Sensor rated IP67 for dust and water (less than 1 m) resistance Robertshaw Controls Ranco ETC-211000-000 Electronic Temperature Control, 120/208/240 VAC, SPDT, -30 to 220 deg F,
  ,
  
  
  
  

  Robertshaw C906-59

ETC Series Electronic Controls The Ranco ETC Series Electronic Temperature Control offers a full-featured electronic replacement for electrical-mechanical temperature controls used in many commercial refrigeration applications. With its wide temperature range, one and two stage capability, selectable heating/cooling modes and multi-voltage input, the ETC is designed to provide application flexibility. Models available include 120/208/240V AC and 24V AC.

• LCD read-out for sensor temperature, control settings and relay status
• High amp output relay (16 amp full load at 120 VAC and 8 amp full load at 208/240 VAC) single stage
• EEPROM memory retains control settings during power outages
• Keypad lockout to prevent end-user alteration of settings
• 8 feet lead with sensor is extendable up to 400 feet using 18 or 22 ga thermostat wire
• Easy 4-step set-up
• Heavy-duty relay is 1 HP rated
• Selectable deg F or deg C heating or cooling modes
• 1 and 2-stage models
• NEMA 1 case and cover
• NEMA 4x models available
• White backlight on display
• Sensor rated IP67 for dust and water resistance
• 0 - 95% RH non-condensing
• 0 - 10 volt no output

Sid Harvey Item #:C906-58: Replaces Part #:'s : A419ABC-1,
,

Robertshaw C906-58

Field Controls FC150HRV Heat Recovery Ventiltor

Field Controls FC150HRV

All Fas-n-Seal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on Fas-n-Seal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All Fas-n-Seal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

M & G Duravent FSVL3604

All Fas-n-Seal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on Fas-n-Seal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All Fas-n-Seal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

M & G Duravent FSVL1205

All Fas-n-Seal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on Fas-n-Seal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All Fas-n-Seal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

M & G Duravent FSELB9003

All Fas-n-Seal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on Fas-n-Seal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All Fas-n-Seal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

• Fas-n-Seal is for use with natural gas or propane categories II, III and IV appliances or type BH gas vent systems, having a maximum rated operating temperature of 480 deg F and a maximum positive pressure of 15" water column
• Fas-n-Seal can be used on a wide range of applications, including high efficiency gas boilers, furnaces, booster heaters, pool heaters, water heaters, unit heaters or tankless water heatersM & G Duravent FSELB4503 Fas-n-Seal Storm Collar 3" Aluminum,

  M & G Duravent FSELB4503

All Fas-n-Seal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on Fas-n-Seal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All Fas-n-Seal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

M & G Duravent FSA-WEIL-CGI

All Fas-n-Seal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on Fas-n-Seal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All Fas-n-Seal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

M & G Duravent FSTT3

All Fas-n-Seal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on Fas-n-Seal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All Fas-n-Seal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

M & G Duravent FSVL2403

All Fas-n-Seal (single-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90 deg from mechanical locking bands. This construction feature allows for ease of installation. The 1/2" air space between the inner and outer wall on Fas-n-Seal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. All Fas-n-Seal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time.

• Fas-n-Seal is for use with natural gas or propane categories II, III and IV appliances or type BH gas vent systems, having a maximum rated operating temperature of 480 deg F and a maximum positive pressure of 15" water column
• Fas-n-Seal can be used on a wide range of applications, including high efficiency gas boilers, furnaces, booster heaters, pool heaters, water heaters, unit heaters or tankless water heatersM & G Duravent FSVL603 Fas-n-Seal Gas Vent Pipe 3" x 6" Natural Gas Stainless Steel,

  M & G Duravent FSVL603

K-Flex Insul-Tube is a Flexible, closed-cell elastomeric tube insulation product used to conserve energy and prevent condensation on piping applications. The product's closed-cell structure creates exceptional thermal properties (k-value of 0.245 at 75 deg F and wvt of 0.03 perm-in) that protect against moisture penetration in applications within a -297 to 220 deg F temperature range. K-Flex Insul-Tube is widely used for its cold weather flexibility, durable skin surface, exacting manufacturing tolerances and lasting performance.

• Insulated tube pipe insulation is an elastomeric material that helps retard heat loss, prevents condensation and provides effective moisture vapor resistance
• Environmentally friendly, CFC free, mould and mildew resistant, fiber free and non-dusting
• Can be used in underground applications above the water table
• Seal before back filling
• Unslit tubing can be slit lengthwise and fit over existing pipes
• <7% linear shrinkage dimensional stability
• <0.01 perm" water vapor permeability

  K-Flex J4