Danfoss 013G8044 Nickel-Plated Brass Straight Thermostatic Radiator Valve Body, 3/4", Solder Union

• Valve bodies are designed to meet the demands of the residential, commercial and industrial sectors
• Thermostatic radiator valves regulate the flow of hot water or low pressure steam through free-standing radiators, baseboards or convectors in hot water and 2-pipe steam systems
• Valves are fitted with a packing gland assembly that is replaceable while the system is in operation
• EPDM rubber valve disc provides a seal against the valve seat at differential pressures of up to 15 psig in hot water heating systems, while 15 psig for low pressure steam systems
• Manual plastic cap supplied to protect the valve pusHPin and provide manual control of the valve during installation
• Valves remain normally open with no operator mounted
• Brass bonnet, spindle, nickel-plated brass tailpiece, union nut, EPDM disc, packing O-ring, stainless steel spring

Sid Harvey Item #:013G8044: Replaces Part #:'s : 5847,
,

Danfoss 013G8024

Danfoss 013G8024 Nickel-Plated Brass Thermostatic Radiator Angle Valve, 1", FPT x MPT Union Tailpiece

• Thermostatic radiator valves regulate the flow of hot water or low pressure steam through free-standing radiators, baseboards or convectors in hot water and 2-pipe steam systems
• Valves are fitted with a packing gland assembly that is replaceable while the system is in operation
• EPDM rubber valve disc provides a seal against the valve seat at differential pressures of up to 15 psig in hot water heating systems, while 15 psig for low pressure steam systems
• Manual plastic cap supplied to protect the valve pusHPin and provide manual control of the valve during installation
• Valves remain normally open with no operator mounted
• Brass bonnet, spindle, nickel-plated tailpiece, union nut, EPDM disc, packing O-ring, stainless steel spring

Sid Harvey Item #:013G8024: Replaces Part #:'s : 5841
,
,

Cold Point 40138

A double-acting control for gas-fired furnaces and boilers is widely used for conversion burner installations, gas draft-induced appliance operation with mechanical draft inducers, or sidewall power venters. It is also recommended for use on gas atmospheric appliances where a draft hood cannot be installed, and can improve combustion stability and draft on many gas atmospheric installations with venting problems. The MG-1 provides precise, accurate control of drafts at levels higher than permitted by a standard draft diverter, which is a frequent requirement with gas.

,
,

Field Controls 100-10

Field Controls 02724001 Silver Barometric Draft Control for Gas-Fired Furnaces and Boilers is Widely Used for Conversion Burner Installations, Gas Atmospheric Appliances, 6"

• 28.3 sq-inch capacity
• 5 - 6" pipe size
• 24 ga (ring and gate), 26 ga (collar) thickness
• Because it is double acting, it opens out to relieve positive vent system pressures as low as 0.01"
• Can improve combustion stability and draft on many gas atmospheric installations with venting problems
• Provides precise, accurate control of drafts at levels higher than permitted by a standard draft diverter

Sid Harvey Item #:100-10: Replaces Part #:'s : 40573,
,

Field Controls 100

VentRite 1VT Nickel-Plated, Hand Polished Brass Adjustable Steam Vent Air Valve, 1/8", Male

• All vents are factory assembled, tested and inspected in the USA
• Each vent is individually packed with External labeling for convenience and maintenance
• Our vents have all brass internals with nickel plated and hand polished exterior
• Every Vent-Rite vent is factory assembled, tested and inspected in the USA
• #1 adjustable vent has a wide adjustment conveniently located below steam path

Sid Harvey Item #:1VT: Replaces Part #:'s : B154 | HYD205-B154 |,
,

Vent-Rite Corporation 11VT

Watts Water BBFP-S Forged Brass Dual Check Backflow Preventer with Series BBFP is specially made for smaller supply lines and ideally suited for laboratory equipment, processing tanks, sterilizers, dairy equipment and similar applications. It is particularly recommended for boiler feed lines to prevent backflow when supply pressure falls below system pressure. Series BBFP is suitable for use on hot or cold water and can be used under continuous pressure. It features a primary check valve utilizing a rubber disc seating against a mating rubber part to ensure tight closing. A secondary check valve utilizes a rubber disc-to-metal seating. In the event of fouling of the downstream check valve, leakage would be vented to atmosphere through the vent port thereby safeguarding the potable water system.Sid Harvey Item #:1/2 BBFP-S: Replaces Part #:'s : 2K558S,
,

Watts Water 0342692

Coleman Mfg 10SMK Insulated Non-Asbestos Cement

,
,

coleman manufacturing 10smk

Tjernlund DJ-3 In-line Induced Draft Blower for Smokepipe and Aids Proper Exhaust of Combustion Gas, 115 VAC , 1/70 HP, 1550 RPM

• Thermal protected
• Aluminized steel blower wheel

Sid Harvey Item #:106: Replaces Part #:'s : 17140,
,

Tjernlund 100-12

Tjernlund D-3 Aluminized Steel Housing Inline Draft Inducer, 115 VAC, 0.96 amp, 1550 RPM, 1/20 HP

• Venturi action starts air moving up the stack instantly and keeps it moving smoothly
• In-line inducers are built for long-lasting, trouble-free service
• Vari-draft control permits adjustment to individual job requirements
• Vents/chimneys utilizing in-line draft inducers must be vertically terminated above the roof line
• Solves venting problems: Undersized chimneys, negative pressures, long horizontal vent connectors, down drafts, cold equipment starts, restrictive heat exchangers/combustion chambers
• 1 year warranty Tjernlund D-3 Aluminized Steel Housing Inline Draft Inducer, 115 VAC, 0.96 amp, 1550 RPM, 1/20 HPSid Harvey Item #:106-1: Replaces Part #:'s : x89-444,
  
  ,
  
  
  
  

  Tjernlund 106

Tjernlund I Inline Draft Inducer, 115 VAC , 1/4 HP, 1725 RPM

,
,

Tjernlund 106-10

Sid Harvey Carlin 40287 Universal Flange Gasket for Oil Burner, 4" ID

Sid Harvey Item #:1041:,

Lynn Products 9510

Tjernlund Specially designed to terminate Tjernlund Side Wall Vent Systems. They are also an approved method of terminating many horizontally vented appliances. Vent hoods feature heavy duty, corrosion resistant aluminum construction. Models VH1-3, 4 and 6 also have an additional heat shield for built in clearances from combustibles. Building exteriors are kept clean while the aesthetics of the structure remain undisturbed. All mounting hardware is included.

• 8" square rough-in
• Mounting hardware

Sid Harvey Item #:106-20: Replaces Part #:'s : x89-442,
,

Tjernlund 106-2