Sealed Unit Parts SH281 Universal Door Heater

• 36-1/2' 3 Watts 120 VAC,
  
  ,
  
  
  
  

  Sealed Unit Parts SH250

Sealed Unit Parts SH282 Universal Door Heater

• 18' 3 Watts 120 VAC,
  ,
  
  
  
  

  Sealed Unit Parts SH281

Tjernlund The SideShot models SS1 and SS2 SideWall Vent Systems include the UC1 Universal Control for increased safety, performance and reliability. Designed for oil fired heating equipment or a deluxe gas vent system. Patented vent termination propels flue gases at high velocities away from the building exterior, a necessity when venting oil fired equipment. Both models can be installed with zero clearance to combustible materials and have stainless steel construction in critical areas. Factory wired safety and operating controls allow simple interlock with any burner. The new model SS2 features a self-cleaning stainless steel, backward inclined impeller and sealed ball bearing motor for virtually maintenance free installations. Ultra-fine draft adjustment and slide-out access to all internal components. Easy multiple appliance interlocks with our MAC Series multiple appliance controls.

• Use to side wall vent non-condensing oil fired boilers, water heaters and furnaces that otherwise would require a conventional roof top terminated chimney
• Built-in interlock control with redundant high limit safety switch interfaces easily with thermostat, aquastat or primary controls
• Adjustable pre and post purge timing and easy fault code retrieval
• Stainless steel construction in all critical components including outdoor terminus
• Patented design jets flue gases away from the outside wall to eliminate potential staining of siding
• Slide out service drawer and material handling stainless steel impeller

Sid Harvey Item #:SS2: Replaces Part #:'s : 6H167A,
,

Tjernlund HS-J

Tjernlund 46235000 Stainless Steel Universal Replacement Motor Assembly, 6"

• Field Controls 46235000 Stainless Steel Universal Replacement Motor Assembly, 6",
  ,
  
  
  
  

  Tjernlund SS2

Beckett Parts SP150281U Pump Strainer Kit

Beckett Parts SP150281U

Easy Heat SR51J250 Heater Cable 120 VAC x 250'

Easy Heat SR51J250

Gas and oil heating appliances generate heat through the combustion of fuel. The heat is transferred through the heat exchanger and distributed to the conditioned space. The products of combustion, however, must be vented safely out of the structure. In a conventional chimney, venting is achieved by the natural lifting action of the hot combustion gas. New, efficient systems absorb more of the heat in the heat exchanger and produce lower temperature vent gas. Lower temperature gas does not rise as quickly or as reliably as in older, less efficient systems. Power venting or sidewall venting is more economical and safer than chimney venting. A power venter uses a motorized blower to vent the products of combustion. A power venter is interlocked with the appliance to ensure that proper draft is achieved before the appliance burner is activated.

• 100% negative pressure in the vent pipe for maximum safety
• Standard Galvanized pipe can be used instead of expensive stainless steel
• No need to seal vent pipe joints, saving time and money
• Significantly longer vent lengths than positive pressure, direct vent systems
• The SWG recommended by major heating appliance
• Thermal protected
• Power vent and backing plate included

,
,

Field Controls SWG-4HDS

Field Controls SWGII-6 Power Venter 6" 115 VAC,
,

Field Controls SWGII-5S

Gas and oil heating appliances generate heat through the combustion of fuel. The heat is transferred through the heat exchanger and distributed to the conditioned space. The products of combustion, however, must be vented safely out of the structure. In a conventional chimney, venting is achieved by the natural lifting action of the hot combustion gas. New, efficient systems absorb more of the heat in the heat exchanger and produce lower temperature vent gas. Lower temperature gas does not rise as quickly or as reliably as in older, less efficient systems. Power venting or sidewall venting is more economical and safer than chimney venting. A power venter uses a motorized blower to vent the products of combustion. A power venter is interlocked with the appliance to ensure that proper draft is achieved before the appliance burner is activated.

• 100% negative pressure in the vent pipe for maximum safety
• Standard Galvanized pipe can be used instead of expensive stainless steel
• No need to seal vent pipe joints, saving time and money
• Significantly longer vent lengths than positive pressure, direct vent systems
• The SWG recommended by major heating appliance
• Thermal protected
• Power vent and backing plate included

Sid Harvey Item #:SWGII-5: Replaces Part #:'s : 39968,
,

Field Controls SWGII-4HD

Field Controls SWG-4HDS Stainless Steel Power Venter, 4", 115 VAC at 60 Hz, 1.7 amp, 138 watt The safest, most efficient power venter available today. Gas and oil heating appliances generate heat through the combustion of fuel. The heat is transferred through the heat exchanger and distributed to the conditioned space. The products of combustion, however, must be vented safely out of the structure. In a conventional chimney, venting is achieved by the natural lifting action of the hot combustion gas. New, efficient systems absorb more of the heat in the heat exchanger and produce lower temperature vent gas. Lower temperature gas does not rise as quickly or as reliably as in older, less efficient systems. Power venting or sidewall venting is more economical and safer than chimney venting. A power venter uses a motorized blower to vent the products of combustion. A power venter is interlocked with the appliance to ensure that proper draft is achieved before the appliance burner is activated.

• 100% negative pressure in the vent pipe for maximum safety
• Standard Galvanized pipe can be used instead of expensive stainless steel
• No need to seal vent pipe joints, saving time and money
• Significantly longer vent lengths than positive pressure, direct vent systems
• The SWG is recommended by major heating appliance manufacturers
• Thermal protected The safest, most efficient power venter available today. Gas and oil heating appliances generate heat through the combustion of fuel. The heat is transferred through the heat exchanger and distributed to the conditioned space. The products of combustion, however, must be vented safely out of the structure. In a conventional chimney, venting is achieved by the natural lifting action of the hot combustion gas. New, efficient systems absorb more of the heat in the heat exchanger and produce lower temperature vent gas. Lower temperature gas does not rise as quickly or as reliably as in older, less efficient systems. Power venting or sidewall venting is more economical and safer than chimney venting. A power venter uses a motorized blower to vent the products of combustion. A power venter is interlocked with the appliance to ensure that proper draft is achieved before the appliance burner is activated.Sid Harvey Item #:SWG-4HDS: Replaces Part #:'s : x89-857,
  ,
  
  
  
  

  Field Controls MG1-5

Field Controls SWGII-5S Power Venter 5" 115 VAC 3k RPM 290k Btu Stainless Steel,
,

Field Controls SWGII-5

Strainer Screen & Cylinder SSC-128 Danfoss Old Style Pump & Gasket,
,

Strainer Screen & Cylinder S70BIO